ROHL TTD45W1L Therm and Pressure Balance Trim Instruction Manual

June 9, 2024
ROHL

ROHL TTD45W1L Therm and Pressure Balance Trim

ROHL TTD45W1L Therm and Pressure Balance Trim product

HELPFUL TOOLS
For safety and ease of installation, the use of these helpful tools is recommended.ROHL TTD45W1L Therm and Pressure Balance Trim
01 For warranty or additional information, contact:
QUEBEC / MARITIMES / WESTERN CANADA
houseofrohl.ca/support
1-866-473-8442

US Customers
U.S.A.
houseofrohl.com/support
1-800-777-9762

Canadian Customers
ONTARIO
houseofrohl.ca/support
1-800-287-5354
ROHL TTD45W1L Therm and Pressure Balance Trim 02

Parts List

  • A. Valve Assembly
  • B. Valve Test Plug
  • C. Valve Cover and Plaster Ground
  • D. Mounting Bracket Assembly
  • E. Wall Plate
  • F. Cartridge
  • G. Decorative Sleeve
  • H. Retaining Nut
  • I. Rosette
  • J. Handle
  • K. Handle Set Screws (x2)
  • L. Handle Plug Buttons (x2)

Icon Legend
ROHL TTD45W1L Therm and Pressure Balance Trim 03
STANDARD WALL
ACRYLIC WALL
ROHL TTD45W1L Therm and Pressure Balance Trim 6If installed with a standard wall, remove Valve Cover and Plaster Ground (C). If installed with an acrylic wall, remove Valve Cover (C).
ROHL TTD45W1L Therm and Pressure Balance Trim 07Remove test plug (B) from Valve Assembly. Turn off stops. Remove test plug for flushing.
ROHL TTD45W1L Therm and Pressure Balance Trim 08Suggested: Open stop. Flush the hot and cold supplies 20 seconds each.ROHL TTD45W1L Therm and Pressure Balance Trim 09With stops in the close or vertical position, install Cartridge (F) into the Valve Assembly. Red inlet will be on the left, blue inlet will be on the right. Ensure that the ends of the Cartridge are installed correctly. Red marking on the Cartridge to be installed on the hot water line. Blue marking on the Cartridge to be in-stalled on the cold water line.
ROHL TTD45W1L Therm and Pressure Balance Trim 10Slide Cartridge Nut onto Cartridge and hand tighten.
ROHL TTD45W1L Therm and Pressure Balance Trim 11Do not overtighten the cartridge nut. Mark a line on the nut and body. With a wrench, rotate the nut closed 1/4 turn. Turn on the stops and check for leaks.
ROHL TTD45W1L Therm and Pressure Balance Trim 12Install Decorative Sleeve (G) and Retaining Nut (H). Tighten nut, hand tight only.
ROHL TTD45W1L Therm and Pressure Balance Trim 13Install the Mounting Bracket Assembly (D) and secure with Mounting Bracket Assembly Screws (x2). Shorten the screws as needed. Apply sealant to the edges.
ROHL TTD45W1L Therm and Pressure Balance Trim 14Install the Wall Plate (E) onto the Mounting Bracket Assembly. Once the Wall Plate is installed, install the Rosette (J).
ROHL TTD45W1L Therm and Pressure Balance Trim 15Install the Handle (J). Once the Handle is installed, insert and tighten the Handle Set Screws (K) (x2) to the underside of the Handle. Once the Handle is secured tightly, insert the Handle Plug Buttons (L) (x2).
ROHL TTD45W1L Therm and Pressure Balance Trim 16Installation is complete.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ROHL User Manuals

Related Manuals