HEINNER MG-Y1800X Meat Grinder User Manual

HEINNER MG-Y1800X Meat Grinder

INTRODUCTION

Before using the appliance, please read carefully this instruction manual and keep it for future reference. This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance. In order to operate the unit correctly and safety, please read this instruction manual carefully before installation and usage.

CONTENT OF YOUR PACKAGE

• Meat grinder
• Sausage accesory
• Tomato accesory
• 3 cutting plates, 1 knife, food tray, pusher
• User manual
• Warranty card

SAFETY MEASURES

• Household use only. Do not use for industrial purpose.
• Always disconnect the appliance from the supply if it is left unattended and before assembling, disassembling or cleaning.
• Switch off the appliance and disconnect from supply before changing accessories or approaching parts that move in use.
• Close supervision is necessary when any appliance is used near children.
• When carrying the unit be sure to hold the motor housing with both hands.
• Do not carry the unit by holding only the hopper plate or head.
• Do not fix the cutting blade and cutting plate when using kibbe attachment.
• Never feed food by hand. Always use food pusher.
• Do not grind hard food such as bones, nuts, etc.
• Do not grind ginger and other materials with hard fiber.
• Continuous running of meat grinder should be not more than 10 minutes with the motor cool down to room temperature before switching on again.
• Reverse function is prohibited while the appliance is operating (For example switch “ON” knob to “R” knob or on the contrary), wait at least one minute until grinder has come to a complete stop，otherwise it may cause an abnormal noise, vibration or a transitory electric spark in the appliance. It could result easily damage to appliance and make a user frightened.
• After use, there would be a little food left in the grinder head. This is normal. There might be a bit of black metal powder adhering to the food ground in the end. Please pick them out and throw away, do not eat them.
•  To avoid jamming, do not force to operate the unit with excessive pressure.
• When the circuit breaker activates, do not switch on.
• Never try to replace the parts and repair the unit by yourself.
• This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
• Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved.
• Children shall not play with the appliance.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid a hazard.

SAVE THESE INSTRUCTIONS. HOUSEHOLD USE ONLY.

DESCRIPTION

1. Hopper plate
2. Cutting plate (coarse)
3. Motor housing
4. Fixing ring
5. ON/OFF
6. Cutting blade
7. REV
8. Sausage attachment
9. Unlock button
10. Kibbe attachment
11. Food pusher
12. Head inlet
13. Head
14. Adjustable screw
15. Feed screw
16. Dam-board knob attachment
17. Cutting plate (fine)
18.  Screen
19. Cutting plate (medium)
20. Tomato attachment snake
21. Tomato attachment bracket

FOR THE FIRST TIME

• Check that voltage indicated on the rating label corresponds to the mains voltage in your home.
• Wash all parts (except body) in warm soapy water.
• Before plugging in, ensure the “ON/OFF/ Reverse” switch is turned to “OFF” position.

INSTRUCTION FOR USE

ASSEMBLING

• Holding the head and insert it in the inlet with one hand, place the locking knob into the hole on the side of the motor housing, tighten it clockwise to secure the head (fig.2).
• Place the feed screw into the head, long end first, by turning the feed screw slightly until it is set into the motor housing (fig.3).
• Place the cutting blade onto the feed screw shaft with the blade facing the front as illustrated (fig.4). If it is not fitted properly, meat will not be ground.
• Place the desired cutting plate next to the cutting blade, fitting protrusions in the slots (fig.5).
• Support or press the centre of the cutting plate with one finger then screw the fixing ring until tight with another hand (fig.6). Do not over tighten.
• Place the hopper plate on the head and fix into position.
• Locate the unit on a firm place.
• The air passage at the bottom and the side of the motor housing should be kept free and not blocked.

MINCING MEAT

• Cut all foods into pieces. Sinewless, boneless and fatless meat is recommended, approximate size 20 mm x 20 mm x 60 mm, so that they fit easily into the hopper opening.
• Plug in and turn the “ON/OFF” switch to “ON” position.
• Feed foods into the hopper plate. Use only the food pusher (fig.7).
• After use switch the unit off and unplug it from the power supply.

REVERSE FUNCTION

• In case of jamming switch the appliance off by turning the “reverse” switch.
• Feed screw will be rotating in the opposite direction, and the head will get empty.
• If it doesn’t work, switch the unit off and clean it.

MAKING KIBBE

STUFFING

• Mutton 100g
• Olive oil 1 1/2 tablespoons
• Onion (cut finely) 1 1/2 tablespoons
• Spices to your taste
• Salt to your taste
• Flour 1 1/2 tablespoons
• Mince mutton once or twice.
• Fry onion until brown and add minced mutton, all spice, salt and flour.

OUTLET COVER

• Lean meat 450g
• Flour 150-200g
• Spices to your taste
• Nutmeg (cut finely) 1
• Powdered red pepper to your taste
• Pepper to your taste

• Mince meat three times and mix all ingredients together in a bowl. More meat and less flour for outlet cover create better consistency and taste.
• Grind the mixture three times.
• Disassemble by reversing the steps from 5-3 to remove the cutting plate and cutting blade.
• Place kibbe attachments onto the feed screw shaft together, fitting protrusions in the slots (fig.8).
• Screw fixing ring into place until tight. Do not over tighten (fig.9).
• Make the cylindrical outlet cover (fig.10).
• Form kibbe as illustrated below and deep fry.

MAKING SAUSAGE

• Before starting please assemble sausage attachment as per following (fig.11)
• Operate the steps according to the instructions of MINCING MEAT which mention above.

TOMATO JUICER

• Put the fix ring through the tomato juicer bracket (fig. A).
• Revolve the adjusted nail to the front of tomato juicer basket(fig. B).
• Pack the attachments like fig. C-D.
• Put the containers under tomato juicer attachment like fig. E to collect juice and residue. Cut the tomato into fix meat grinder like head size, then press them gently, it can short the working time.
• Adjust the screw can make the juice dense or thin.
• Disassembly and clean the tomato juicer as soon as juice completely.

CLEANING

DISASSEMBLING

• Make sure that the motor has stopped completely.
• Disconnect the plug from the power outlet.
• Disassemble by reversing the steps from 6-1 pictures.
• If the fixing ring is not easily removed by hands, please use tools（fig.12）.
• To remove the cutting plate easily, place a screwdriver between the cutting plate and the head as illustrated and lift it up (fig.13).
• Press the unlock button before removing the head. Holding the head, rotate it in the same direction as fig.14. Then the head can be removed easily.

CLEANING

• Before you clean the appliance, switch the appliance off and remove the plug from the socket.
• Never clean the unit by a dishwasher.
• Remove meat, etc. Wash each part in warm soapy water.
• A bleaching solution containing chlorine will discolor aluminum surfaces.
• Do not immerse the motor housing in water, but only wipe it with a damp cloth.
• Thinners and petrol will crack or change the color of the unit.
• Wipe all the cutting parts by vegetable oil -wet cloth.
• Wash all the metal parts in water below 50℃ and dry, in case the unit is left unused for a long period of time, wipe them by vegetable oil -wet cloth.

ACCESSORIES STORAGE

• The storage compartment is on the back of the unit as picture (A-1).
• Push the cover of storage compartment to open it as picture (A-2).
• Put the clean accessories (such as blade, cutting plates, sausage attachment, kibbe attachment) into the storage compartment as picture (A-3).

TECHNICAL DETAILS

• Max Power 1800W
• Mincing capacity ≤2 kg/min
• Voltage 220-240V; 50-60Hz

Environment friendly disposal
You can help protect the environment! Please remember to respect the local regulations: hand in the non-working electrical equipment’s to an appropriate waste disposal center.

HEINNER is a registered trademark of Network One Distribution SRL. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from NETWORK ONE DISTRIBUTION. Copyright © 2013 Network One Distribution. All rights reserved. www.heinner.com, http://www.nod.ro

This product is in conformity with norms and standards of European Community.

Importer: Network One Distribution Marcel Iancu Street, 3-5, Bucharest, Romania Tel: +40 21 211 18 56, www.heinner.com , www.nod.ro

References

• Heinner – large appliances, small appliances, housekeeping, DIY
• Heinner – large appliances, small appliances, housekeeping, DIY
• NOD - Network One Distribution
• NOD - Network One Distribution

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>