HEINNER MG-1340WH Meat Grinder User Manual

HEINNER MG-1340WH Meat Grinder

MEAT GRINDER

Model: MG -1340WH

• www.heinner.com
• Meat Grinder
• Power: 1340W
• Color: White

INTRODUCTION

B efore using the appliance, please read carefully this instruction manual and keep it for future r eference. This instruction manual is designed to provide you with all required instructions related to the in stallation, use and maintenance of the appliance. In order to operate the unit correctly and safety, please read this instruction manual carefully before in stallation and usage.In order to avoid rust we advise you to lubricate the cutter unit and the grinding discs with so me vegetable oil.

CONTENT OF YOUR PACKAGE

• Meat grinder
• User manual
• Warranty card

DESCRIPTION

INTRODUCTION

This appliance is equipped with a thermostat system. This system will automatically cut off the po wer supply to the appliance in case of overheating.

If you r appliance suddenly stops running:

1. Pull the mains plug out of the socket.
2. Press the switch button to turn off the appliance.
3. Let the appliance cool down for 60 minutes.
4. Put the mains plug in the socket.
5. Switch the appliance on again.
6. This appliance shall not be used by children. Keep the appliance and its cord out of reach of chil dren.
7. Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction con cerning use of the appliance in a safe way and if they understand the hazards involved.
8. Children shall not play with the appliance.
9. Switch off the appliance and disconnect from supply before changing accessories or approach ing parts that move in use.
   Please contact your dealer of an authorized service center if the thermostat system is activat ed too often. If you plug in, the indicator light will be on.

CAUTION : In order to avoid a hazardous situation, this appliance must never be connected to a tim e switch.

IMPORTANT

1. Read these instructions for use carefully and look at the illustrations before using the applian ce.
2. Befo re use, tight the fixing ring by spanner, make sure the ring can not be detached by 4 Nm.
3. Keep these instructions for future reference.
4. Check if the voltage indicated on the appliance corresponds to the local mains voltage before y ou connect the appliance.
5. Never use any accessories of parts from other manufacture. Your guarantee will become invalid if such accessories or parts have been used.
6. D o not use the appliance if the mains cord, the plug or other parts are damaged.
7. f the power cord of this appliance is damaged, it must always be replaced by man ufacture or a service center authorized, in order to avoid hazardous situations.
8. Thoroughly clean the parts that will come into contact with food before you use the app liance for the first time.
9. Unplug the appliance immediately after use.
10. Never use your finger or an objection to push ingredients down the feed tube while the appliance is running. Only the pusher is to be used for this purpose.
11. Keep the appliance out of the reach of children.
12. Never let the appliance run unattended.
13. Switch the appliance off before detaching and install any accessory.
14. Wait until moving parts have stopped running before you remove the parts of the app liance.
15. Never immerse the motor unit in the water or any other liquid, nor rinse it under the tap . Use only a moist cloth to clean the motor unit.
16. Do not attempt to grind bones, nuts or other hard items.
17. Never reach into the cutter housing. Always use the pusher.
18. Mincers are fed with sinewless, boneless and fatless beef that has been cut into pieces app roximately 20 mm x 20 mm x 60 mm. Pushers are pressed with a force of 5N against the meat. Do not use the appliance for more than 5 minutes consecutively. Leave the app liance to cool for 10 minutes before using again.
19. Accessories shall include instructions for their safe use.
20. It shall warn of potential injury from misuse.
21. This appliance is not intended for use by persons (including children) with reduced phy sical, sensory or mental capabilities, or lack of experience and knowledge, unless they hav e been give supervision or instruction concerning use of the appliance by a person respo nsible for their safety.
22. Children should be supervised to ensure that they do not play with the appliance.
23. If the appliance is locked, please press Reversal button(REV). The meat locked in cutter hou sing is untrodden, so the appliance can renew its usual condition.
24. Disposal of appliances and batteries.
25. After the implementation of the European Directive 2002/96/EU in the national legal syst em, the followi ng applies:
    • Electrical and electronic devices may not be disposed of with domestic waste. Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject t o these regulations. By recycling, reusing the materials or other forms of utilising old devices, you are making an important contribution to protecting our environment.
26. This appliance can be used by children aged from 8 years and above if they have been given superv ision or instruction concerning use of the appliance in a safe way and if they understand the haz ards involved. Cleaning and user maintenance shall not be made by children unless they are ag ed from 8 years and above and supervised. Keep the appliance and its cord out of reach of childr en aged less than 8 years.
27. This appliance is intended to be used only in household.

USING INSTRUCTIONS

ASSEMBLING

1. Press the fastening button, hold the head and insert it into the inlet(when inserting please pay attention the head must be slanted as per the arrow indicated on the top, see fig.1),then move the head anticlockwise so that the head being fastened tightly (fig.2).
2. Place the snake into the head, long end first, and turn to feed the screw slightly until it is set into the motor housing (fig.3).
3. Place the cutting blade onto the snake shaft with the blade facing the front as illustrated (fig .4). If it is not fitted properly, the meat will not be ground.
4. P lace the desired cutting plate next to the cutting blade, fitting protrusions in the slot (fig.5) .
5. Support or press the center of the cutting plate with one finger then screw the fixing ring tight with another hand (fig.6). Do not over-tighten.
6. Place the hopper plate on the head and fix it into position.
7. Locate the unit on a firm place.
8. The air passage at the bottom and the side of the motor housing should be kept free and not blocked.

MINCER

1. Insert the worm shaft into the cutter housin g, the plastic end first. Place the cutter unit onto the worm shaft (the cutting edges should be at the front). Place the medium grinding disc or coarse grinding disc (depending on the consistency you prefer) ont o the worm shaft. Make sure the notch of the grinding disc fit onto the projections of the min cer head. Turn the screw ring in the direction of the arrow on the cutter housing until it is properly fastened.
2.  Attach the cutter housing to the motor unit.
3. Place the tray on the upright part of the cutter housing.
4. Now the appliance is ready for mincing.

Cut the meat into 10cm-long, 2cm-thick strips. Remove bones, pieces of gristle and sinews as mu ch as possible. Never use frozen meat! Put the meat in the tray. Use the pusher to gently push the meat into the cutter hosing. For st eak tartare, mince the meat with the medium grinding disc twice.

MAKING KEBBE

1. In sert the worm shaft into the cutter housing, the plastic end first (fig.8). Place the cone in the cutter housing. Place the former on the cutter housing and screw the ring on the cutter housing (fig.9).
2. Attach the cutter housing to the motor unit.
3. Place the tray on the upright part of the cutter housing.
4. Now the appliance is ready for making kebbe (fig.10).
5. Feed the prepared kebbe mixture through the kebbe maker. Cut the continuous hollow cylinder into the desired lengths and user as required.
6. Kebbe is a traditional Middle Eastern dish made primarily of lamp and bulgur wheat which are minced together to form a paste the mixture is extruded through the kebbe maker and cut into short lengths. The tubes can then be stuffed with a minced meat mixture, the ends pinched together and then deep fried.

MINCER

1. Insert the worm shaft into the cutter housing, the plastic end first.
   Place the cutter unit onto the worm shaft (the cutting edges should be at the front). Place the medium grinding disc or coarse grinding disc (depending on the consistency you prefer) onto the worm shaft. Make sure the notch of the grinding disc fit onto the projections of the mincer head. Turn the screw ring in the direction of the arrow on the cutter housing until it is properly fastened.

2. Attach the cutter housing to the motor unit.

3. Place the tray on the upright part of the cutter housing.

4. Now the appliance is ready for mincing.

Cut the meat into 10cm-long, 2cm-thick strips. Remove bones, pieces of gristle and sinews as mu ch as possible. Never use frozen meat! Put the meat in the tray. Use the pusher to gently push the meat into the cutter hosing. For st eak tartare, mince the meat with the medium grinding disc twice.

MAKING SAUSAGES

1. Mince the meat
   Insert the worm shaft into the cutter housing, the plastic end first (fig.11).
   Place the cutting plate and the blade in the cutter housing.
   Place the sausage horn on the cutter housing and screw the ring on the cutter housing.(M ake sure the notches of the cutting plate fit onto the projections of the mincer head.)

2. Attach the cutter housing to the motor unit.

3. Place the tray on the upright part of the cutter housing.

4. Now the appliance is ready for making sausages.

Pu t the ingredients in the tray. Use the pusher to gently push the meat into the cutter ho using. Put the sausage skin in lukewarm water for 10 minutes. Then slide the wet skin onto the sau sage horn. Push the (seasoned) minced meat into the cutter housing. If the skin gets stuck onto the sausage horn, wet it with some water.

TOMATO ACCESSORY

ASSEMBLING

1. Place the plastic screw locking ring into the sleeve (fig.1).
2. Place the gauze into the sleeve next to the plastic screw locking ring (fig.2).
3. Put the fixing ring through the sleeve and make it at the end of the sleeve (fig.3).
4. Place the snake into the head, long end first, and turn to feed the snake slightly until it is set into the motor housing (fig.4).
5. Insert the shaft of the snake into the central axis of the screw (fig.5).
6. Put the whole sleeve along with the fixing ring through the screw, then move the fixing ring clockwise so that it being fastened tightly (fig.6).
7. Put the plastic juice tray through the sleeve and make it on the suitable position (fig.7).
8. Insert the plastic screw into the hole of the sleeve, then move it clockwise until it is properly fastened. Then place the plastic cover onto the sleeve (fig.8). Now the appliance is ready for juicing.

CLEANING AND MAINTENANCE

M eat left behind in the cutter housing may be removed from the inside of the appliance by passing a slice of bread through the cut ter housing.

1. Before you clean the appliance, switch the appliance off and remove the plug from the socket (fig.12).
2. Press the release button and turn the whole cutter housing in the direction of the arrow. Remove the pusher and the tray (fig.13).
3. Unscrew the screw ring and remove all parts of the cutter housing. Do not clean the parts in the dishwasher!
4. Wash all parts that have come into contact with meat in hot soapy water. Clean them immediately after use.
5. Rinse them with clear hot water and dry them immediately.
6. We advise you to lubricate the cutter unit and the grinding discs with some vegetable oil.

TECHNICAL DATA

• Power: 1340W
• Voltage: 220-240V, 50-60Hz
• Mincing capacity: 1.2 kg/min
• Color: White

Environment-friendly disposal
You can help protect the environment! Please remember to respect the local regulations: hand in the non-working electrical equipment’s to an appropriate waste disposal center.

HEINNER is a registered trademark of Network One Distribution SRL. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from NETWORK

ONE DISTRIBUTION
Copyright © 2013 Network One Distibution. All rights reserved. www.heinner.com, http://www.nod.ro http://www.heinner.com, http://www.nod.ro

This product is in conformity with norms and standards of European Community.

• Importer: Network One Distribution
• Str. Marcel Iancu, nr. 3-5, Bucuresti, Romania
• Tel: +40 21 211 18 56, www.heinner.com , www.nod.ro

References

• Heinner – large appliances, small appliances, housekeeping, DIY
• Heinner – large appliances, small appliances, housekeeping, DIY
• NOD - Network One Distribution
• NOD - Network One Distribution

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>