sauermann CO 50 Portable Tachometer User Guide
- June 9, 2024
- sauermann
Table of Contents
sauermann CO 50 Portable Tachometer
Class 50 portables
These portable instruments are used to measure the following parameters: temperature, relative humidity, CO, pressure, air velocity and light.
- Operating temperature, protection of the instruments and information about storage Conditions of use (°C/%RH/m): from 0 to +50 °C. In non-condensing conditions. From 0 to 2000 m.
Protection: IP54
Storage temperature: HD 50, LX 50: from -20 to +70 °C. CT 50, CO 50, HM 50, LV 50, MP 50, MP 51, MP 55, VT 50: from -20 to +80 °C. If the instrument is stored outside the operating temperature (for example in a van, a warehouse…), please wait for 10 minutes in its operating temperature before start using it.
Keys
Take a measurement
- VT 50: before using the instrument with the hotwire probe, please lower the protection tube (1) of the sensing element.
- VT 50: always use the hotwire probe with the red point in front of flow.
Switch on
the instrument by pressing briefly on “On/Off/Hold”.
The instrument displays its name then the measurement.
CO 50: the instrument displays its name then a 5 second countdown. This count corresponds to the preheating time of the sensor. At the end of the countdown, the measured value of CO is displayed.
MP 50, MP 51: the instrument displays its name then an autozero is performed. At the end of the autozero, the measured value displays.
Press briefly on “Select” to switch measurement parameter display.
- MP 50, MP 51, MP 55: press briefly and successively on “Select” to change the unit.
- Available units for MP 50: Pa, mmH20, inWg, daPa.
- Available units for MP 51: mmH20, kPa, in Wg, mbar, mmHg, daPa.
- Available units for MP 55: mbar, mmHg, hPa.
HBM 50: press briefly on “Select” to select a type of material.
Press the spikes in the material to be measured.
When a measurement is over-range, above the maximum range, the value flashes.
Below the minimum range, the value is no more measurable and the device
indicates “—“, it means that for:
- Wood type 1: the measurement is < than 10%
- Wood type 2: the measurement is < than 9%
- Plaster, brick and concrete: the measurement is < than 0.1%
Carry out a manual autozero (MP 50, MP 51)
During measurement:
Remove pressure tubes. Carry out a long press on “Select”.
The instrument makes an autozero then returns to the measurement display.
Hold the measurement
During measurement, press briefly on “On/Off/Hold” to hold measurement: “Hold”
appears on the screen and measurements are fixed.
CO 50, HD 50, HM 50, LX 50, MP 55, VT 50: press briefly on “Select” to move
from one parameter to the other. Press again briefly on “On/Off/Hold” to exit
the Hold function.
Change the unit
The instrument is on.
CO 50, CT 50, HD 50, LX 50:
Carry out a long press on “Select” to change the unit.
Press briefly on “Select” to select the required unit of measurement.
Carry out a long press on “Select” to confirm the unit and return to the
normal measuring mode.
VT 50:
Change the air velocity unit:
Press briefly on “Select” up to display the air velocity.
Carry out a long press on “Select” to change the air velocity unit.
Press briefly on “Select” to select the required unit of measurement.
Carry out a long press on “Select” to confirm the unit and return to the
normal measuring mode.
Change the temperature unit:
Press briefly on “Select” up to display the temperature.
Carry out a long press on “Select” to change the temperature unit.
Press briefly on “Select” to select the required unit of measurement.
Carry out a long press on “Select” to confirm the unit and return to the
normal measuring mode.
Select the velocity type: contact or optical (CT 50)
The instrument is on.
Carry out a long press on “Select”: “Cont” or “Optic” flashes.
Press briefly on “Select” to select contact velocity (“Cont”) or optical
velocity (“Optic”). Carry out a long press on “Select” to confirm.
Perform a self-test (HM 50)
Turn the instrument on. Remove the cap and turn the cap.
Press “Select” to select the type of material to verify.
Press the 2 pins of the instrument into the contact plugs of the cap.
Read the value indicated by the instrument:
- If the indicated value matches with the given value in the table below, the instrument runs properly.
- If the indicated value does not match with the given value in the table below, clean the tips and carry out a new self-test. If the value is still wrong, change the pins. If it does not work, please contact the after sales service.
Materials humidity 
Batteries replacement
The instrument is OFF.
Remove the front part at the back of the instrument. Replace used batteries by
new batteries AAA LR03 1.5 V. Replace the front.
To ensure safety, replace batteries with the same type.
Not doing so might lead to explosion. Dispose of used batteries according to
instructions.
Auto shut-off
The instrument switches off if it is not used during 20 minutes.
Download the data sheet
Sauermann Industrie
ZA Bernard Moulinet
24700 Montpon
France
T. +33 (0)5 53 80 85 00
services@sauermanngroup.com
Sauermann NA
140 Fell Court, Ste. 302 Hauppauge, New York 11788
T. (+1) 631-234-7600
F. (+1) 631-234-7605
info.usa@sauermanngroup.com
Sauermann GmbH
Leibnizstraße 6
D – 74211 Leingarten
T. +49 (0)7131/399990
F. +49 (0)7131/399992
info.germany@sauermanngroup.com
Sauermann UK
Units 7-9, Trident Business Park Amy Johnson Way
Blackpool – FY4 2RP
T. +44 (0) 870 950 6378
F. +44 (0) 870 950 6379
info.uk@sauermanngroup.com
Sauermann Italia srl S.U
Via Golini 61/10
40024 Castel S.Pietro Terme (BO)
T. (+39)-051-6951033
F. (+39)-051-942254
info.italy@sauermanngroup.com
Sauermann Ibérica
C/Albert Einstein 33.
Planta 3. P. I. Santa Margarida II-08223 Terrassa (Spain)
T. +34 931 016 975
info.spain@sauermanngroup.com
Sauermann Australia
1/36 Campbell Avenue, Cromer ,2099,
NSW, Sydney
T. (+612) 8880 4631 sauermannpumps.com.au
Sauermann China
No. 1, Changxu Road, Juyuan New Park,
Jiading District, Shanghai
T. (+86) 6100 1877
F. (+86) 6100 1870
info.china@sauermanngroup.com
Customer service portal
Use our Customer service portal to contact us
https://sauermann-en.custhelp.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>