AQUA CREST AQ-5KDC-S Under Sink Direct Connect Water Filtration System Instruction Manual
- June 14, 2024
- AQUA CREST
Table of Contents
AQUA CREST AQ-5KDC-S Under Sink Direct Connect Water Filtration System
Product Information
Ultra High Capacity Under Sink Direct Connect Water Filtration System
The Ultra High Capacity Under Sink Direct Connect Water Filtration System is designed to provide clean and filtered water directly from your cold water supply line. With a capacity of 5,000 gallons or 12 months, this filtration system ensures optimal performance and prevents the growth of bacteria and fungus in your filter and supply lines. The system is easy to install and comes with various fittings and accessories for a hassle-free setup.
Model: AQ-5KDC-S
Operating Specifications
- Minimum operating temperature …………………………………………………………………………………………………………………………………………………………………………………………………0.6°C/33°F
- Maximum operating temperature ……………………………………………………………………………………………………………………………………………………………………………………………… 38°C/100°F
- Minimum working pressure …………………………………………………………………………………………………………………………………………………………………………………………………….140 kPa/20 psi
- Maximum working pressure …………………………………………………………………………………………………………………………………………………………………………………………. 689 kPa/100 psi
- Rated capacity ……………………………………………………………………………………………………………………………………………………………………………………………………….18,927 litres/5,000 gallons
- Flow rate ……………………………………………………………………………………………………………………………………………………………………………………………………………………………………..5.5 lpm/1.5 gpm
Storage and maintenance
- Replace your filter every 12 months or 5,000 gallons to achieve optimal performance and prevent bacteria and fungus growth in your filter and supply lines.
- Keep your unused filters in a cool, dark, and dry place until you need them.
Installation instructions
- Step 1: Turn off the cold water valve and turn on the faucet to ensure that there is no residual water.
- Step 2: Remove the cold water hose from the cold water valve.
- Cold water valve’s size and needed fittings
If the angle valve outlet is 3/8″, it can be directly connected to the water supply.- If the angle valve outlet is 1/2″, it can be connected via the following two fittings.
- Step 3: Connect the 3/8″ or 1/2”female compression end of the inlet hose to the cold water valve. Connect the other end of the inlet hose to the filter inlet. (The inlet is on the cap side marked with “IN”.) The external part of the connector is about 0.1″ long when the hose is inserted in place.
- Step 4: Connect the 3/8″ or 1/2”male compression end of the outlet hose to the faucet hose. Connect the other end of the outlet hose to the filter outlet.
- Note: Do not forget to install the cold water hose connection gasket.
- Note: If the double female threaded hose is needed, please contact customer service.
- Step 5: Select the proper fittings to fix the filter.
- Option 1-Bracket: Select the proper position on the cabinet wall. Install the bracket and then push the filter into the bracket.
- Option 2-Cable tie mounts: Take out 4 cable tie mounts and select the proper position for pasting them. Thread the cable ties into the cable tie mounts and fix the filter.
- Step 6: Turn on the cold water valve to flush the filter for 5 minutes. Check for any leakage.
Caution: This filter should not be used with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
Frequently Asked Questions
- Q: What should I do if water leaks at the connection after installing the filter?
- A: Turn off the cold water valve and check the water leakage. If the leakage is at the connections between the hosesand the cold water valve or inlet hose, remove the hoses and confirm whether the connection gasket is installed in place, or wrap Teflon tape on the external thread. If the water leakage is at the connections between the hoses and the filter, make sure that the hoses are inserted to the end and that the inserted length is about 4/5″.
- Q: Does the filter have to be replaced every 12 months?
- A: Yes, we recommend that the filter be replaced every 12 months. If the filter is overused, bacteria may grow in it and affect the water quality. If the water flow slows down or if many impurities are deposited in the filtration system, the filter may need to be replaced sooner. The service life will vary based on the condition of your water.
- Q: Does the filter need to be flushed after installation?
- A: Yes, we recommend that you turn on the faucet and flush the filter for 5 minutes after installation. The filter media contains coconut shell activated carbon, so there is a small amount of carbon foam in the filter. Flushing will ensure that the filtered water is clear.
- Q: How do I remove the hoses from the filter?
- A: Use your thumb and index finger to press down on the lock sleeve. Use your other hand to pull the hose out of the filter.
- Do not pull out the hose directly, as this will damage the fitting and cause leakage.
Warning
To reduce the risk of property damage due to water leakage, this filter MUST be installed in accordance with the manufacturer’s specifications and instructions.
- This filter unit must be replaced every 5,000 gallons or every 12 months.
- Do not use this product at temperatures under 32°F/0°C; otherwise, the product will freeze.
- Use municipal water as your source water.
Failure to follow the instructions and operating specifications will void your quality assurance. Further, the manufacturer assumes no responsibility or liability for damages arising out of misuse of the product.
*The service life mentioned above is subject to chlorine reduction.
Actual result varies according to the local water quality.
Contact
Manufacturer Technical Support
- Tel: 1-888-352-3558 (U.S.)
- E-mail: service@water-filter.com
- Made in China V040
- Qingdao Ecopure Filter Co., Ltd.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>