sauermann CT 110 Tachometer User Manual

Table of Contents

sauermann-CT-110-Tachometer-prodact-img

sauermann-CT-110-Tachometer-fig-8

Measuring elements Optical tachometry: optical detection (Phototransistor sighting distance max. 40 cm)
Contact tachometry: ETC adaptator for optical tachometry probe
Display 4 lines, LCD technology. Dimensions: 50 x 36 mm 2 lines of 5 digits with 7 segments (value) 2 lines of 5 digits with 16 segments (unit)
Connector Coiled, 0.45 m length, extension: 2.4 m
Housing ABS, protection IP54
Keypad 5 keys
European directives 2014/30/EU EMC; 2014/35/EU Low Voltage; 2011/65/EU RoHS II; 2012/19/EU WEEE
Power supply 4 batteries AAA LR03 1.5 V
Ambience Neutral gas
Conditions of use (°C, %RH, m) From 0 to +50 °C. In non condensing conditions. From 0 to 2000 m.
Storage temperature From -20 to +80 °C
Auto shut-off Adjustable from 0 to 120 min
Weight 190 g

sauermann-CT-110-Tachometer-fig-1

All the accuracies indicated in this technical datasheet were stated in laboratory conditions, and can be guaranteed for measurements carried out in the same conditions, or carried out with calibration compensation.

If the type of selected probe is the contact probe, put the contact tip on the probe.

Display the minimum and the maximum

Once the measurements are frozen

Press again on “Hold/min/max“.
The device displays the maximum value of velocity measured since the last questioning at the top of the screen and the minimum value of velocity measured since the last questioning at the bottom of the screen.
Press again on “On/Off/Esc“ to return to the measurement display.

Adjust the device

Device drop-down menu

sauermann-CT-110-Tachometer-fig-2

Select the probe type

It is possible to select the probe type: optic probe or contact probe.

Press on “Select“.
“PROBE“ blinks on screen.
Press on “OK“.
The probe type currently used blinks on the screen.
Press on “Select“ to select “OPTIC“ for the optic probe or “CONT“ for the contact probe.
Press on “OK“ to validate.
“PROBE“ blinks on screen.
Press on “On/Off/Esc“ to return to the measurement display.

sauermann-CT-110-Tachometer-fig-3

Select the measuring unit

The device is on and displays the measurement.

Press on “Select“ until “UNIT“ blinks on screen.
Press on “OK“, the unit currently used blinks on screen.
For the contact probe: press on “Select“ until the required unit appears: tr/min, rpm, m/min, in/min, ft/min or m/s.
For the optic probe: press on “Select“ until the required unit appears: tr/min or rpm.
Press on “OK“ to validate the unit selection. “UNIT“ blinks on screen.
Press on “On/Off/Esc“ to return to the measurement display.

sauermann-CT-110-Tachometer-fig-4

Adjust the auto shut-off

The device is on and displays the measurement.

Press on “Select“ until “AUTO OFF“ blinks on screen.
Press on “OK“.
The time before device auto shut-off blinks at the bottom of the screen.
Press on “Select“ to select the time before device auto shut-off: 15, 30, 45, 60, 75, 90, 105, 120 or OFF.
Press on “OK“ to validate.
Press on “On/Off/Esc“ to return to the measurement display.

sauermann-CT-110-Tachometer-fig-5

Activate or deactivate the keys beep

The device is on and displays the measurement.

Press on “Select“ until “BEEP“ blinks on screen.
Press on “OK“.
“OFF“ or “ON“ blinks on screen.
Press on “Select“ to activate the keys beep “ON“ or deactivate the keys beep “OFF“.
Press on “OK“ to validate.
“BEEP“ blinks on screen.
Press on “On/Off/Esc“ to return to the measurement display.