JOYROOM 202 Magnetic Phone Holder User Manual

JOYROOM 202 Magnetic Phone Holder

IMPORTANT MESSAGE TO ENSURE SUCCESSFUL INSTALLTION AND USE.

High bond adhesives are tricky please follow all the instructions carefully.

Here is a short list of the most crucial tips:

1. Install at room temperature only;
2. Never touch 3M stickers with fingers;
3. Degrease the surface,wait till dry;
4. Press firmly for 10 Sec for strong bond;
5. Wait 24 hours before use;
6. Contact us if any help is needed-support@kirakudous.com
7. This car mount support 18 months warranty.

This car mount uses high-performance 3M VHB adhesive for best results, follow these instructions carefully.
Car mount components should be installed on the hard surface in room temperature environment(ABOUT 70℉[21℃]).

Metal Disc Installation Instructions

1. The smaller disc can be adhered directly to the back of most phones or over cases.
2. The bigger disc can be adhered under a slim phone case.
3. Discs are not magents, they a just metal.
4. Prior use the mount,test whether the fixation is strong enough to hold your phone in a car

• Clean the back of the phone/case with the enclosed alcohol Pad. LET DRY.
• Remove the adhesive backing from the metal disc.
• Position the disc in the center of the back of the device and firmly press into place.

In case you use a WIRELESS CHARGER please position the disc not to cover the QI CHIP.

• Wait one hour after application for sufficient cure.

Smaller and bigger metal phone disc

Metal phone discs 3M VHB adhesive backing.

Dashboard mount installation instructions

1. Before removing adhesive backing, test the position of the mount with phone in different spots on the dash to find the best one. The mount should be installed onto a HARD&SMOOTH SURFACE such as flat hard plastic, metal, glass or wood veneer.
2. Clean the chosen area with the enclosed alcohol pad, be sure to WAIT UNTIL DRY, the alcohol can reduce the adhesive’s stickiness.
3. Peel the adhesive backing backing from the mount bottom and press firmly into place for 10 SECONDS.
4. WAIT 24 HOURS prior to use to allow sufficient adhesive cure time.*IN COLD/HOT WEATHER INSTALL THE MOUNT IN A WARMED/COOLED CAR ONLY.

Removal Instructions

1. Apply a Few drops of rubbing alcohol (Go gone works even better) between the mount component and the surface it has been applied to in order to break the adhesive bond.
2. Carefully use fishing ling or dental floss in a sawing motion to cut foam away from the surface(see illustration above). Using your finger, roll, the remaining adhesive away.

DO NOT RE-USE 3M ADHESIVE.New adhesives are provided in a reinstall kit included in a set.

A REINSTALL KIT FOR THE MOUNT IS INCLUDED IN A SET.

1. To reinstall, simply remove any remaining adhesive from the installation site, if applicable. Please ensure that all mount components are free of residual adhesive using your finger. Roll the remaining adhesive away from the applied surface clean all surfaces with the alcohol pad and wait until dry before installing the new adhesive disc.
2. To ensure a successful reinstall, please never touch the adhesive disc on either the metallic disc or the dash ball mount.
3. Once surfaces are clean and the adhesive has been reinstalled, please refer back to step 1 of the installation instructions and proceed through all of them.

MAGNET WARNING:

1. While the item’s phone discs are just metal(not magnetic), the mount’s base contains a strong magnet. It will not damage devices with solid-state drives like android phones, Apple, etc.
2. However, magnets can damage sensitive objects including pacemakers, compter hard-drives (including ipod players’ hard-drives), credit cards, magnetic I.D cards, and other similar items.
3. We assume no liability for damage to such objects.

Kirakudo
support@kirakudous.com
www.kirakudous.com
Kirakudo. ALL RIGHTS RESERVED.

Frequently Asked Questions

Can I use the car mount with a case?

Yes, you can use it with a case.

How do I clean my device?

Use the enclosed alcohol pad to clean the back of your phone or case. Let dry before applying the metal disc.

What if I don’t have a metal plate on my phone?

The metal disc is optional and can be removed.

What if I don’t have a case on my phone?

The metal disc is optional and can be removed.

Can the magnet be used with phone cases?

If there is a magnet there, it ought to work. Some phones lack magnets, in which case a case with a magnetic mount will also be necessary.

To a textured dashboard with this mount?

According to the texture. The 3M adhesive is quite durable. I’ve taken the holders off and put them back on with the same tape, and it still holds firmly. My dash also has some texture.

Will any credit cards in the phone case be harmed by the magnets?

No, I still have my working credit cards in their case.

Does magnetic force have an impact on the phone’s hardware or battery?

The function and signal of the phone won’t be impacted by the magnetic car phone mount. So, don’t be concerned.

Does magnetic force have an impact on the phone’s hardware or battery?

Don’t put the plate directly over your NFC-capable phone if you want to be able to charge it. Any phones that lack NFC may charge without issue. Phones without NFC have no effects.

If you sandwich the metal component between your phone and its case, would this mount still be able to retain it? My argument is weak.

The thin case on your phone would fit in the vehicle mount, yes. Put the metal plate correctly within the case or on the case’s surface. it could be effective. The best material available right now is an N52 neodymium magnet. extremely powerful magnet Additionally, there are 6 magnets, which is 2 more than the average. The phones will be adequately taken care of by the mount.

Does it have the proper mounting angle for a cell phone to use as a dashcam?

Yes, depending on where you set it and provided the phone has unrestricted movement. The magnet is rather powerful and holds quite well.

Why are there so many additional yellow stickers?

The mount may be attached to it after the yellow stickers have been placed. It makes it much simpler to remove the mount when you wish to. You want to harm the surface by removing the mount, then.

Does this function with the iPhone 12 Pro?

Simply attach the metal plate to the rear and it will work with whatever phone you choose.

Could it accommodate my iPad mini?

I utilise it using an iphone XR. When its rear component is tightly fastened, my phone will stop rotating. It was quite difficult to unhook my phone from the metal piece that you place on your phone to hold it; I tried using it on the back of my case. I would contrast your device’s weights with an XR. I believe it would hold up well.

Video

JOYROOM 202 Magnetic Phone Holder PDF

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>