WLN KD-C172L Handheld 2 Way Radio User Manual

WLN KD-C172L Handheld 2 Way Radio

Product Information

Specifications:

• Model: KD-C170L, KD-C172L
• Frequency Range: 462.5500-462.7250MHz, 467.5625-467.7125MHz
• Output Power: 30.95dBm (462.5500-462.7250MHz), 25.49dBm (467.5625-467.7125MHz)
• Channels: 22 (ERP)

Product Usage Instructions

Powering On/Off:
To power on the device, switch the Power Switch to the ON position. To power off, switch it to the OFF position.

Selecting Frequency/Channel:
Use the Function Key to select the desired frequency/channel within the supported range.

Using the Earphone Jack:
Connect your earphones to the Earphone Jack for private listening.

Charging the Device:
Connect the Charging Port to a compatible charger to recharge the device.

Attaching the Belt Clip:
Clip the device onto your belt using the Belt Clip for convenient carrying.

Desktop Charging:
For desktop charging, connect the device to the Desktop Charger Connector.

FAQ (Frequently Asked Questions):

• Q: What should I do if the device is not powering on?
  A: Ensure that the Power Switch is in the correct position and that the battery is charged. If the issue persists, contact customer support.

• Q: How can I change the frequency/channel?
  A: Use the Function Key to cycle through and select different frequencies/channels available within the supported range.

• Q: Can I use any charger with the Charging Port?
  A: It is recommended to use a compatible charger with the specified voltage and current ratings to avoid damage to the device.

FEATURES

• Wireless Clone
• One-click Code Breaking
• Screen Display
• Scanning
• Monitoring
• VOX
• TOT
• Chinese/English Voice Prompt
• Keyboard Lockout
• Power Display
• Busy Channel Lockout
• High-Low Power Selection
• Power Saving Mode
• Low Battery Warning
• Voice Companding/Scrambling Function
• Special Signaling
• 50 CTCSS/208 DCS
• Model: KD-C170L. KD-C172L

Charging the Battery Pack

1. The battery is not charged in the factory, please charge the battery under the environmental temperature 5—40°C before using.
2. After purchasing or long-term storage(more than two months), charging the battery for the first time can not reach its saturation capacity,repeat charge/discharge for twice or three times to make battery capacity achieve the best state.
3. Before charging, please power off the transceiver, using the transceiver during charging may affect correct charging.
4. If the battery has been charged fully, please do not charge it again, otherwise the service life of the battery may be shortened or may be damaged.
5. If the service time is significantly reduced even after completely correct charging, the battery can not be used any more, please replace a new battery.

OVERVIEW

Be Familiar With The Machine:

Icons:

1. LOGO icon: you can input the logo or the number of the user via the software.
2. HEADPHONES icon: after inserting headphones, headphones icon displayed, you can use the headphones to talk.

Operation

Basic Operation:

1. Turn the power switch to turn on /off the transceiver.
2. Short press [UP] key or [DOWN] key to adjust the channels.
3. PTT: press this button whenever you wish to talk with the users of the other transceivers.

Functions Operation:

• Scanning
  It is convenient for the user to search for calls from other channels. When “Side Key 1 or Side Key 2” in the software is programmed to the scanning function, long press [UP DOWN) keys for two seconds to enter into the scanning mode, the transceiver will start to scan with the current channel; Operate them again to exit.

• Keyboard Lockout
  Long press [FUNCTION KEY] to lock all buttons, and operate it again to unlock.

• Monitoring
  When”Side Key 1 or Side Key 2″ in the software is programmed to the monitoring function, long press [UP] [DOWN] keys for two seconds to enter into the monitoring mode, release them to exit.

• Chinese/English Voice Selection
  The transceiver has a manual switching function between the Chinese and the English voice.
  Press [FUNCTION KEY] to enter the menu, select “VOICE” to enter into the language selection, then press the [FUNCTION KEY] to confirm.

• One-click Code breaking
  Turn the transceiver to Channel 1 and turn it off,then press [DOWN] key and turn it on, “Scan Freq…” displayed, the transceiver enter into the code- breaking mode. When any transceiver transmits, if the transceiver receive the signal, the screen will display the deciphered frequencies, that is,the channel has been deciphered, short press [ FUNCTION KEY] to save to the channel. The transceiver can be used normally after restarting it.

• Wireless Clone
  Turn the two transceivers to Channel 2 and turn them off, then press [DOWN) key and turn them on, “FSKcopy…”displayed and green light flashes, press the PTT key of the transceiver which need to be cloned to start the data transmission. The transceiver can be used normally after restarting it.

• Time Out Timer(TOT)
  The purpose of the TOT is to prevent any single person from using a channel for an extended period of time. An alarm will sound if the transmission continues beyond the set time. The transceiver will stop transmission if this occurs. To stop the alarm, release the PTT key and the transceiver will return to standby.

• Busy Channel Lockout
  The function can prevent interference from other transceivers using the same channel. Press [ FUNCTION KEY] to enter the menu, select “BCL” to enter into the selection of ON/OFF.

• Battery Power Saving
  If there is no signal or operation, the transceiver will reduce its power consumption. The battery power-saving function activates when the channel is unoccupied or has not been in operation.

• Low Battery Warning
  If the battery power falls to the predetermined value during transmission, the transceiver will give out a voice prompt, please charge in time.

• Scrambling
  It is a voice encryption mode which is different from sub audio.

• Companding
  It is a function setting which prevents the inter-channel interference.

• CTCSS/DCS
  The transceiver has 50 CTCSS and 208 DCS, also non-standard sub-audio can be programmed!

• Special Signaling
  Special Signaling refers to the CDCSS on the channels which is special processed codes. Only when the transceivers in the same company are programmed to the same frequency point with the same CDCSS and meanwhile special signaling is set, then they can talk to each other.

Technical Parameters

We May Change The Specifications For Technical Improvement Without Prior Notice.

FCC Statement

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

SAR tests are conducted using standard operating positions accepted by FCC/ISEDC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. Before a new model is available for sale to the public, it must be tested and certified to the FCC/ISEDC that is does not exceed the exposure limit established by the FCC/ISEDC. Tests for each product are performed in positions and locations as required by the FCC/ISEDC.

For body-worn operation, this device has been tested and meets the FCC/ISEDC RF exposure guidelines when used with and accessory designated for this product or when used with and accessory that contains no metal.

To maintain compliance with FCC/ISEDC RF exposure guidelines hold the transmitter and antenna at least 1 inch (2.5 centimeters) from your face and speak in a normal voice, with the antenna pointed up and away from the face.

The equipment complies with FCC/ISEDC radiation exposure limits set forth for and uncontrolled environment. In order to comply with the FCC/ISEDC RF exposure requirement, the antenna installation must comply with following:

Users must be fully aware of the hazards of the exposure and able to exercise control over their RF exposure to qualify for the higher exposure limits. Your wireless hand-held portable transceiver contains a low-power transmitter. This product sends out radio frequency (RF) signals when the Push-to-Talk(PTT) button is pressed. The device is authorized to operate at a duty factor not to exceed 50%.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>