JOYROOM ZS387 Cooling Fan Magnetic Wireless Car Charger Mount User Manual
- June 1, 2024
- Joyroom
Table of Contents
User Manual
ZS387 Cooling Fan Magnetic Wireless Car Charger Mount
ZS387 Cooling Fan Magnetic Wireless Car Charger Mount
FCC Requirement
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy, and if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help..
PARAMETERS
Model: JR-ZS387
Name: Cooling Fan Magnetic
Wireless Car Charger Mount
Material: PC+ABS+Aluminum Alloy
Input: 5V 2A 9V 2A 12V 2A
Output: 5W/7.5W/10W/15W (MAX)
Input port: Type-C
Size: ≈6666100mm
Net weight: ≈105g
Applicable phone size: 4.7″-7.0”
Product diagram
Fan/Light Button
- Click the button to turn on/off the fan (only when charging the phone);
- Press and hold the button for 3s to turn on/off the light
Accessory kit
Operation steps (vent hook)
- Put the ball head into the nut first, then insert it into the socket on the back of the holder, tighten the nut.
- Clip hook using method: Press the button, extend the hook to hook onto the vent blade, release the button, then tighten the knob clockwise.
Note: When removing the clip hook, make sure to loosen the knob counterclockwise before pressing the button. - Use the Type-C charging cable in the package to connect the holder and the car charger.
Operation steps (metal ring)
- Open the cleaning kit, wipe clean the back surface of your phone.
- Paste the transparent separation film onto the center of the phone back.
- Paste the metal ring onto the center of the phone back by use of the alignment card. Note: As long as the upper and lower scales, the left and right scales of the alignment card are equal, the metal ring will be pasted right to the center of the phone.
- Place your phone. It will be securely attached to the charger holder with its auto alignment function.
Reminder: The product can be used directly with iP mag-safe phones as well as magnetic cases. For other phones and cases, a metal ring is required.
Indicator light/Fan
| Power on | Light turns on, the fan works for 10s then stops |
|---|---|
| Standby | Constant light, the fan doesn’t work |
| Changing | Light breathes, the fan works |
| FOD | Light flashes quickly, the fan doesn’t work |
Warranty Card
User Name:|
---|---
User Tel:|
User address (with postcode):|
Purchase date:|
Invoice No.:|
Dealer Name:|
Dealer Tel:|
Dealer Address (with postcode):|
Warranty
A. If there is performance failure on this product and it’s not caused by
human error, we will provide a 12-month free warranty service for consumers
from the date of purchase.
B. Warranty exceptions:
- Human damage;
- Expired the warranty period;
- Failure to provide valid purchase certificate;
- Product damage caused by failure to follow the use, maintenance and care instructions;
- Product damage caused by disassembling or repairing the product without authorization, or immersing the product in water
- Damage caused by force majeure.
© 2024 Shenzhen Nito Power Source Technology Co, Ltd.
All Rights Reserved / Designed by JOYROOM /
www.joyroom.com / Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>