Sunco Lighting XS-XEBB05-25WAC Emergency Battery Backup Instructions
- July 10, 2024
- Sunco Lighting
Table of Contents
Sunco Lighting XS-XEBB05-25WAC Emergency Battery Backup
FAQ
- Q: What should I do in case of an emergency operation?
- A: Before touching or disconnecting any wires, make sure to press the test button to turn off the LED lamp and indicator light to avoid electric shock.
- Q: What is the maximum wattage recommended for use with this Emergency LED Driver?
- A: For the XS-XEBB05-25WAC model, it is recommended to work with LED lamps not exceeding 210W.
Features
- UL Listed for US and Canada
- Listed to UL924 and tested to CSA C22.2
- NO.141 Field or factory installation
- High voltage output
- Low energy consumption CEC compliance
- Constant output power
- Self-testing
- Battery: Over temperature protection
Specifications
- Input Voltage: 120~277Vac, 50/60Hz Input
- Current: 200mA max.
- Input Power Rating: 12W max.
- Output Voltage: 170Vdc
- Emergency Power: 25W
- Recharge Time: 24Hrs
- Discharge Time: 90 minute Battery: Li-ion
- Warranty: 5 Years
- Ambient Temp: 32°F ~ 122°F (0°C ~ 50°C)
- Weight: 2.66 lbs (1.2kg)
Model No
| Model No. | Output Voltage | Emergency Power | Battery Type |
|---|---|---|---|
| XS-XEBB05-25WAC | 170Vdc | 25W | Li-ion |
Function
Indicator Light
- AC Operation, indicator light will keep on
- Emergency Operation, indicator light flash slowly (light on for 2 seconds, light off for 2 seconds)
- In a failure, indicator light flash quickly (light on for 0.2 seconds, light off for 0.2 seconds
Test Switch
- In AC Operation, press test switch once, emergency for 30 seconds
- In AC Operation, press test switch twice in asuccession within two seconds, emergency until battery is full discharged
- In the emergency operation, press test switch will turn off emergency status, and led lamp & indicator light of EM driver will go out at the same time
CAUTION
- During AC operation, remember no touch or remove any wires in case of electric shock
- During emergency operation, before touching and disconnecting the wires, remember to press the test button again to make the led lamp and indicator light off to avoid electric shock
- The voltage input to the dimmable wires(DIM+,DIM-) of the emergency LED driver must less than 20Vdc For emergency LED driver of XS-XEBB05-25WAC, better work with LED lamp not more than 210W
Function
Indicator Light
- AC Operation, indicator light will keep on
- Emergency Operation, indicator light flash slowly (light on for 2 seconds, light off for 2 seconds)
- In a failure, indicator light flash quickly (light on for 0.2 seconds, light off for 0.2 seconds
Test Switch
- In AC operation, press test switch or “A” on remote test switch, the fixtures will switch into emergency model for 30 seconds.
- In AC operation, press “B” on remote test switch, the fixtures will switch into emergency model for 90 minutes.
- In emergency operation, 30 senconds later, press “A” on remote test switch 10 seconds later, the fixtures will switch into AC model.
- Without an antenna, the remote signal could reach about 12M, but with the antenna, signal could reach far more than 30M.
Wiring Diagram
- When the led driver power less than the emergency power
Normal
- When the led driver power more than the emergency power
With Dimmer
Without Dimmer
Without Switch and Without Dimmer
With Sensor (AC)
With Sensor (DC12V)
Self-Test
- The emergency LED driver contains a control/monitor circuit which will perform a 30-second discharge test once a month and a fully discharge test once a year. At this time, the unit simulate an AC power failure and automatically switch to emergency mode. During routine testing, the unit will monitor the operation of the LED load, battery voltage, and emergency duration, if the unit detect any problems, the indicator will flash quickly.
Dimension
| Emergency LED Driver | Size (inch) |
|---|---|
| Picture | Length |
| Connector Diameter | Length of the wire |
|
L1
|
L2
|
W1
|
W2
|
/
|
R1
|
R2
|
/
|
/
|
/
|
/
12.32″
|
11.73″
|
2.32″
|
1.65″
|
1.48″
|
0.14″
|
0.08″
|
13″
|
0.75″
|
0.79″
|
5.51″
For wiring to the led driver’s input
Documents / Resources
|
Sunco Lighting XS-XEBB05-25WAC Emergency Battery
Backup
[pdf] Instructions
XS-XEBB05-25WAC Emergency Battery Backup, XS-XEBB05-25WAC, Emergency Battery
Backup, Battery Backup, Backup
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>