JOYROOM JR-MH01 Wireless Speaker with Phone Holder User Manual

JOYROOM JR-MH01 Wireless Speaker with Phone Holder User Manual

User Manual

JR-MH01 Wireless Speaker with Phone Holder

I. Packing list

II. Fold/Unfold diagram

III. Product diagram

V. Basic parameters

Name: Stand sound Model: JR-MH01 BT version: V5.3Audio decoding: SBC Supported protocols: HFP, A2DP, AVRCP Working frequency: 2402-2480MHz BT range: 10m (barrier-free open environment) Frequency response range: 20Hz-20KHz Speaker: φ50mm Rated power: 3W Music time: about 15h (70% volume) Calling time: about 20h (70% volume) Standby time (connected): about 120h Battery capacity: 2000mAh Charging time: about 3h Speaker charging port: TYPE-C Device charging output port: USB Charging input: 5V 1A Charging output: 5V 0.5A Material: ABS+aluminum alloy+silicone Net weight: 391g

V. Connection operations

1. Turn on

Slide the power switch to “ON” position, the speaker will give a “doo-doo-doo- doo” prompt, which means the speaker is turned on.

2. Wireless connection

Turn the phone’s BT function on and search for the BT device “Joyroom Holder MH01”. connect the phone with it, and then you can start to control music via the speaker.

Note: Please connect the speaker manually for the first time, after that it will reconnect to the last connected device automatically. (iP & Android devices connecting in the same way)

3. Turn off

➀ Slide the power switch to “OFF” position

➁ It will automatically turn off if not connected for 5 minutes

VII. Operation instructions

Charging your device via the speaker

Connect one end of the charging cable included to the USB output port of the speaker, connect the other end to the device that needs charging

FAQ

Q: Why can’t the speaker be turned on?

A: Check whether the speaker is out of power. If so, please charge it for more than 30 minutes before turning it on.

Q: Why can’t the speaker be connected?

A: ① The speaker may be out of power. Please charge it for 30 minutes before turning it on, and then search it for connection.

② If your phone uses iOS system, it may be that the speaker did not reconnect to your phone in time. You can directly click the device name “Joyroom Holder MH01” in the phone’s BT list to connect with it.

③ Check whether the speaker is connected to another device. If so, please disconnect with it and make a reconnection again.

④ If above operations failed, you can restore it to factory settings.

Q: Why does jamming/discontinuity occur when playing songs?

A: ① The transmission range of the speaker is 10m, please reduce the distance between the speaker and the device.

② Do not use it in areas with large interference sources to avoid affecting the signal.

③ It may be caused by poor signal or network cache, please use it in such environments with strong phone signal and smooth network.

Q: Why is the sound of the speaker too low or mute?

A: ① It may be that the playback channel of the phone is not turned on. Please turn on your phone’s BT function, click the icon on the right side of connected Joyroom Holder MH01 to open the media and call channel of the phone.

② Open the “Settings” interface of your phone, check if there is a maximum volume limit on the phone.

③ Volume up both the phone and the speaker.

Safety Criteria

1. Please follow the instructions, do not disassemble the product or refit it
   for any reason, otherwise it may break down or burn down.

2. Do not immerse it in any liquid or wash it with

3. Please use adapters that conform to national/regional safety standards together with the included charging cable to charge the product, otherwise its battery may be damaged or cause safety

4. Please use and store it in normal temperatures; too low or too high temperature (below 0℃ or above 45℃) is not

5. Do not block the openings of the product, such as charging port, indicator,

6. Do not use it at high volume levels or for long periods of time to avoid dizziness or hearing

7. Do not use it under thunderstorm which may lead to abnormal performance and signal

WARNING: Before installing or operating the product, please refer to the electrical and safety information on the bottom of the shell.

WARNING: Never expose the battery (or battery pack) to excessive heat, such as sunlight or similar heat sources.

FCC NOTE:

This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:

• this device may not cause harmful interference, and
• this device must accept any interference received, including interference that may cause undesired

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>