PPE 314052200 Heavy-Duty Cast Aluminum Engine Oil Pan Installation Guide

: June 9, 2024
: PPE

Table of Contents

CONTENTS
PREPARATION
INSTALLATION
DISCLAIMER OF LIABILITY
LIMITATION OF WARRANTY
CUSTOMER SUPPORT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PPE 314052200 Heavy-Duty Cast Aluminum Engine Oil Pan Installation Guide

PREPARATION

Step 1: Vehicle off. Engine cool.
Completely drain oil, overnight if possible.
Recycle used oil.
Step 2: Remove skid plate and cross member.
Step 3: Remove stock pan.
Step 4: Thoroughly clean engine housing mating surface.

INSTALLATION

Step 1: Apply a constant bead of engine-rated silicone sealant (RTV) into the machined channel of the flange, including around the screw holes.
Step 2: Preassemble two of the kit’s screws and washers (C, D). Position PPE Oil Pan in place by indexing the locating pins on the flange.
Be careful to apply even pressure so silicone spreads uniformly. Install the two screw assemblies on opposing sides to secure in place, finger-tight for now.
Install remaining assembled hardware (C, D) finger-tight for now.
Step 3: Tighten in a crossing pattern as shown (FIG 1).
Torque to 8-10 ft lbs.
Step 4: Check and torque drain plug (B) to 15-19 ft lbs.
Step 5: Replace old oil filter if necessary.
Step 6: Fill with manufacturer-recommended oil.
Step 7: Torque cross member to 66 ft lbs.
Step 8: Torque skid plate to 30 ft lbs.
Step 7: Start engine. Check fluid level. Check for leaks.

Installation complete.

DISCLAIMER OF LIABILITY

Performance products can increase horsepower above and beyond factory specifications.
Additional horsepower creates more stress on the drive-train components, which could result in drive-train failure.

Note regarding emissions-related, non-E.O.-legal products: THESE PRODUCTS ARE LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER BE USED, OR REGISTERED OR LICENSED FOR HIGHWAY OR OFF-ROAD USE.

This agreement sets forth the terms and conditions for the use of PPE products.
The installation of this product indicates that the Buyer has read and understands this agreement and accepts the terms and conditions. PPE (Pacific Performance Engineering) Inc., its distributors, employees, and dealers (the “Seller”) shall not be responsible for the product’s proper use and service.
The buyer hereby waives all liability claims. The Buyer hereby acknowledges no reliance on the Seller’s skill or judgment to select or furnish goods suitable for any particular purpose and that there are no liabilities which extend beyond the description on the face hereof, and the Buyer hereby waives all remedies or liabilities expressed or implied, arising by law or otherwise (including without any obligation of the Seller with respect to fitness, merchantability and consequential damages), or whether or not occasioned by the Seller’s negligence.
The Seller disclaims any warranty and expressly disclaims any liability for personal injury or damages.
The Buyer acknowledges and agrees that the disclaimer of any liability for personal injury is a material term for this agreement and the Buyer agrees to indemnify the Seller and to hold the Seller harmless from any claim related to the item of equipment purchased.
Under no circumstances will the Seller be liable for any damages or expenses by reason of use or sale of any such equipment.
The Seller assumes no liability regarding the improper installation or misapplication of its products. It is the installer’s responsibility to check for proper installation and if in doubt, contact the manufacturer.
The Buyer is solely responsible for all warranty issues from the manufacturer.

LIMITATION OF WARRANTY

The Seller gives Limited Warranty as to description, quality, merchantability, and fitness for a particular purpose, productiveness, or any other matter of Seller’s product sold herewith.
The Seller shall not be responsible for the products proper use and service and the Buyer hereby waives all rights other than those expressly written herein.
This warranty shall not be extended, altered or varied except by a written instrument signed by Seller and Buyer.
The Warranty on PPE Manifolds and Up-Pipes Kits, OEM-Length Up-Pipes is three (3) years, a limited lifetime warranty on PPE cast aluminum pans and covers, and a limited lifetime warranty on PPE Transmission Coolers and one (1) year limited warranty on all other PPE products from the date of sale to original buyer and limited solely to the parts contained within the products kit.
All products that are in question of Warranty must be returned prepaid to the Seller and must be accompanied by a dated proof of purchase receipt.
All Warranty claims are subject to approval by Seller.
Under no circumstances will the Seller be liable for any labor charged or travel time incurred in diagnosis for defects, removal, or re-installation – of this product or any other contingent expenses.
Under no circumstances will the Seller be liable for any damage or expenses incurred by reason of the use or sale of any such equipment.
In the event that the buyer does not agree with this agreement: the buyer may promptly return this product, in a new and unused condition in its original packaging, with a dated proof of purchase to the place
of purchase within ten (10) days from date of purchase for a full refund.
The installation of this product indicates that the buyer has read and understands this agreement and accepts its terms and conditions.