Avantree AH6B Stereo Wireless Headphones User Manual
- June 9, 2024
- Avantree
Table of Contents
Avantree AH6B Stereo Wireless Headphones
Product Overview
Basic Operation
Note: Functionality varies by application.
Status of LED indicators
| Working Status | LED indicator |
|---|---|
| Paring Mode | Blinks BLUE & RED alternately |
| Reconnecting | Blinks BLUE once every 1 second |
| Disconnected | Blinks BLUE once every 10 seconds |
| Microphone Mute ON | Remains RED |
| Connected | Blinks BLUE once every 5 seconds |
| Low battery | Blinks RED three times every 10 seconds |
Connect to a Bluetooth device
Enter Headphones into Pairing Mode:
Slide the power switch to left and hold for 3 seconds. You’ll hear “Pairing”
and the LED indicator blinks RED and BLUE alternately
Pair to mobile device
- Set the headphones into Pairing Mode as above.
- Activate Bluetooth on your phone and set it to search for new devices.
- Select “Avantree AH6B”, once successfully paired you’ll hear “connected”.
Connect to two Bluetooth devices simultaneously
To add another cell phone
- Connect with the FIRST phone as above, then turn off the headphones.
- Connect headphones with SECOND phone as above.
- Tap and select “Avantree AH6B” on the FIRST phone. Now, Avantree AH6B connected with TWO phones simultaneously.
Reconnect to Bluetooth device
Reconnection
Normally, when the next time you turn on Avantree AH6B, it will automatically
reconnect the last paired device. Alternatively, Slide the power switch to
left once, then release to enter into its Reconnection Mode.
Connect to PC / Laptop
- Set the headphones into Pairing Mode as above.
- Activate Bluetooth function on your PC/Laptop, search & select “Avantree AH6B” to pair and connect.
- For music stream, please set “Avantree AH6B” as the Playback Default Device/Out put device in Sound Setting page.
- For Skype call, please set “Avantree AH6B Hands-free Headset” as microphone and speaker device in Audio Settings.
Using as a wired headphone
Use the supplied 3.5mm audio cable to connect to a non-Bluetooth audio device,
or if the headphone battery is depleted.
Note: The headphone will power off automatically once you plug in the
3.5mm audio cable.
Charging
When the LED flashes RED 3 times per 10 seconds or you hear the voice prompts “Low battery please turn off and charge”, you should fully recharge the device for about 2 hours. Charged with the micro USB cable – The LED indicator on the headphones will remain RED while charging and turn off when charging is complete.
Reset
Clear pairing history
If you have issues with the audio stream skipping or cutting out when using
Avantree AH6B, please try to clear pairing history as following:
Firstly, turn on the headset (Non-calling Status), then Press and Hold BOTH &
5 seconds till the LED blinks PINK for 2 seconds, then the headphones enter
into PAIRING MODE automatically.
Troubleshooting
No sound with PC?
- Set Avantree AH6B as the default device or output device on the PC.
- When using AH6B to make VOIP calls through apps, please set “AH6B Hands-Free” as Microphone and Speakers device.
No sound with Bluetooth transmitter to watching TV?
- Ensure Bluetooth transmitter and headphones are connected properly.
- Check to ensure audio source is functioning properly
- AUX & RCA output on TV – test with wired headphones
- OPT output on TV – Set audio format to “PCM/LPCM” or turn off Dolby/DTS
- Change your TV audio out setting to External speakers / Headset.
Headphones do not pair with Bluetooth device?
- Ensure AH6B is in Pairing mode – LED will flash BLUE and RED alternately.
- For Bluetooth transmitter, ensure the transmitter is in Pairing mode – refer to its user manual.
- For Smart phone, tablet and PC
- Turn the Bluetooth off and then on again.
- Delete “Avantree AH6B headphones” from your devices Bluetooth list and then try to pair again.
- Clear the headphones pairing history and pair again.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>