kogan KAHUDA5CARA Car Head Up Display User Guide

KAHUDA5CARA Car Head Up Display
User Guide CAR HEAD UP DISPLAY
KAHUDA5CARA

COMPONENTS

OVERVIEW

Display (as viewed on windscreen)

1. Buzzer
3. Compass
5. Speed
7. Speed unit (MPH/ Km/h)| 2. Setting
4. Satellite
6. Light sensor
---|---

INSTALLATION

Before First Use

1. Place the non-slip mat on the driver’s side corner of the dashboard and then place the head up display (HUD) on it.
2. Connect charger to vehicle’s 12V socket.
3. Connect the cable to the OBDII input on the unit.
4. Start the engine and the HUD will power on.
5. The RED satellite icon will flash when charged and begin searching for a satellite connection. When the satellite indicator turns GREEN, the HUD is ready for use.

Reflective Film
The HUD projects information up onto the windscreen. Due to the construction of your windscreen, the HUD may create a double reflection on the windscreen, which will  make it difficult to read. If this occurs, install the reflective film.

1. Spray some water onto the inside of your windscreen above where the HUD is installed. Clean the area with a dry cloth.
2. Remove the backside (marked 1) of the film and apply to the windscreen.
3. Ensure the film is installed in the correct location and adjust if necessary.
4. Use a flat plastic object (credit card) to squeeze out any water or bubbles from behind the reflective film.
5. Remove the protective film (marked 2).
6. If the reflective film isn’t positioned to display all the vehicle information, adjust the position of the HUD and non-slip mat until it is correctly aligned.

OPERATION

Input button:
The Input button is a three-way button used to navigate the HUD’s menu and adjust the settings.

• Up: push the button towards the windscreen
• Ok: press the button inwards
• Down: pull the button towards the driver

Using the input button
Press and hold the input button for 5 seconds to enter the menu. When finished adjusting the settings, press and hold the input button for 5 seconds to save changes and exit.

• Up: increases setting value
• Down: decrease setting value
• Down and hold: turn alarm tone on or off
• Ok: short press to change menu selection

Factory Reset
Long pull up and hold. When all LEDs are illuminated, the HUD has been restored to factory settings.
Settings menu
Since the HUD receives data from satellites, the data will vary slightly from the information displayed on the vehicle dashboard. If you find the value on your dashboard is  different to the value displayed by the HUD, you can change it through the following procedure.

Menu| Parameter| Adjustment range| Explanation|

Default

|

Display

---|---|---|---|---|---
1| Speed| 80-120| Up or down to adjust|

107

|
2| Over-speed alarm| 10-180| Sounds alarm when speed is exceeded|

117

|
3| Brightness| 0-5| 1 (darkest) – 5 (brightest) 0 = Automatic|

100

|
4| Speed unit| 0-1| 0= Km/h 1= MPH|

50

|
5| on/off Power voltage| 100-150| Change to 13.2V-14V if HUD does not turn off automatically|

45

|
6| Display mode| 0-1| 0 = reflect on windshield 1 = HUD screen| 0|

SPECIFICATIONS

Standby: 15mA
Speed range| 0-400km
Satellite positioning time| Cold start: 4 mins
Hot start: 45 seconds
Compass precision| ±1°
12V car charger| 1000mA
Weight| 40g
Dimensions| 90x54x12mm

TROUBLESHOOTING

• Press the input button down multiple times
• Connect the HUD to a different 12V socket or another vehicle to ensure the 12V is  functioning correctly
Inaccurate speed| • Ensure the speed unit is correct (MPH/Km/h)
• Adjust the speed value in the settings menu
HUD is not visible in sunlight| • Ensure the reflective film is installed
• Adjust the brightness in the settings menu

NOTES

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com kogan.com

References

• Kogan Help Centre

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>