Weller WXMPS MS, WXUPS MS WXsmart Instruction Manual

: June 8, 2024
: Weller

Table of Contents

Weller WXMPS MS, WXUPS MS WXsmart
WHAT IN BOX
CONNECTION
INSTRUCTION
Safety information
Specified Conditions Of Use
Care and maintenance
Warranty
Technical Data
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Weller WXMPS MS, WXUPS MS WXsmart

Weller-WXMPS-MS,-WXUPS-MS-WXsmart-product-img

WHAT IN BOX

$Weller-WXMPS-MS,-WXUPS-MS-WXsmart-fig- $4$$

CONNECTION

$Weller-WXMPS-MS,-WXUPS-MS-WXsmart-fig- $1$$

INSTRUCTION

$Weller-WXMPS-MS,-WXUPS-MS-WXsmart-fig- $5$$

Read these instructions and the accompanying safety information carefully before starting up the device and starting work with the device.
Failure to observe the safety regulations results in a risk to life and limb.
Keep these instructions in a place that is accessible to all users. Please adhere to the operating instructions of the connected devices.
Please be sure to read and follow the operating instructions for your Weller Supply Unit

Safety information

For safety reasons, children and youths under the age of 16, as well as persons who are not familiar with these operating instructions, may not use the device. Children should be supervised in order to ensure that they do not play with the tool.
This device is not intended for use by persons (including children) with limited physical, sensory or mental aptitude, or by persons who lack knowledge or experience in handling the device.
Always place the soldering tool in the safety rest while not in use.
Keep other persons well away from your workplace.
The work area is out of bounds for children and unauthorised persons. Never allow other persons to touch the soldering tool or cable.

Use only original Weller soldering tips!

WARNING Electrical shock
Protect yourself against electric shocks. The handles on soldering tools with an antistatic design are conductive.

Avoid touching earthed objects such as pipes, heaters, cookers and refrigerators.
Do not use the soldering tool in a damp or wet environment.
Never work on voltage-carrying parts

WARNING Risk of burns

The soldering tip becomes very hot during soldering work. There is a risk of burns from touching the tips.
After the soldering process, the soldering tool and the workpiece holder are still hot.

Always place the soldering tool in the safety rest while not in use. Make sure the safety holder is stable.
Do not touch the hot soldering tips and keep them away from inflammable objects..
Only replace solder tips when cold
Only replace nozzles when cold

Risk of burning through liquid solder. Protect yourself against solder splashes.

Wear appropriate protective clothing to protect yourself against burns. Protect your eyes by wearing eye protection.
When working with adhesives, special attention must be paid to the warning information provided by the adhesive manufacturer.
Only connect the vacuum and hot air at the designated points.

WARNING Fire hazard

Covering the soldering iron or the safety holder poses a fire hazard. Always keep objects well away from the soldering iron and safety holder.

Always keep objects well away from the soldering iron and safety holder.
Keep all combustible objects, liquids or gases well away from the hot soldering tool.
Do not place or leave the hot soldering or desoldering tip on the worktop or on plastic surfaces.
Avoid unintentional operation. Disconnect the soldering tool from the power supply while not in use.
Keep explosive and flammable objects well away from the device.

Store your soldering tool in a safe place. When not in use, units and tools should be stored in a dry, high or locked area out of the reach of children. Make sure that unused soldering tools are free of voltage and de-pressurised.
Do not use the cable for purposes other than those for which it is intended. Never carry the unit by the cable. Do not use the cable to pull the plug out of the socket.
Protect the cable against heat, oil and sharp edges.
Be alert. Pay attention to what you are doing. Be smart when using the unit. Do not use the soldering tool if you are having difficulty concentrating.
Avoid abnormal posture. Arrange your work station in an ergonomically correct way. Avoid bad posture when using the unit, as this can lead to postural problems
The soldering tool must be operated only in perfect technical working order. Safety devices must not be deactivated.
Faults and defects must be repaired immediately.
Before using the unit / tool, safety devices must be carefully checked to make sure that they are functioning properly and in the manner intended. Check that moving parts are functioning properly and are not sticking, and whether parts are damaged. All parts must be correctly fitted and must satisfy all the requirements necessary to guarantee trouble-free operation of the unit.
Use the correct tool. Use only accessories or auxiliary devices which are included in the list of accessories or approved for use by the manufacturer. Use WELLER accessories or auxiliary devices on original WELLER equipment only. The use of other tools and other accessories can cause injury.
Secure the tool. Use clamping fixtures to hold the workpiece.
Use a solder fume extraction unit. If appliances for connecting solder fume extraction units are available, ensure that they are connected and used properly.

Specified Conditions Of Use

Use the soldering iron exclusively for the purpose indicated in the Operating Instructions of soldering and desoldering under the conditions specified here.
The soldering iron may only used in combination with Weller

Supply Units

This device may only be used at room temperature and indoors. Protect against moisture and direct sunlight.

User groups

Due to differing degrees of risk and potential hazards, several work steps may only be performed by trained experts

Work step	User groups
Default soldering para- meters	Specialist personnel with technical training
Replacing electrical repla- cement parts	Electricians
Default maintenance intervals	Safety expert
Operation Filter change	Non-specialists

Operation Filter change

Replacing electrical repla-

cement parts

| Technical trainees under the guidance and supervision of a trained expert

Care and maintenance

$Weller-WXMPS-MS,-WXUPS-MS-WXsmart-fig- $2$$ $Weller-WXMPS-MS,-WXUPS-MS-WXsmart-fig- $3$$

WARNING

Before doing any work on the machine, pull the plug out of the socket. Leave the unit to cool down.
Check all connected cables and hoses on a regular basis. If power tools are damaged, they must be immediately removed from use.
Do not use blocked nozzles

Repairs must always be referred to a Weller-trained specialist.
Use original replacement parts only

WARNING Risk of burns

Only replace the soldering tips when they are cold.
The soldering tool must be left switched off in the safety rest for at least 3 minutes until the soldering tip has cooled down.
The LED status indicator must be at „OFF“.

Temperature performance

The soldering tool has an internal usage sensor which can be used to set an automatic switch-off function (Stand-by).
The settings can be found in the station’s operating instructions.

Warranty

Claims by the buyer for physical defects are time-barred after a period of one year from delivery to the buyer. This does not apply to claims by the buyer for indemnification in accordance with §§ 478, 479 BGB (German Federal Law Gazette).
We shall only be liable for claims arising from a warranty furnished by us if the quality or durability warranty has been furnished by use in writing and using the term „Warranty“.
The warranty shall be void if damage is due to improper use and if the device has been tampered with by unauthorised persons.
For more information please visit www.weller-tools.com.

Symbols

Caution!
Warning! Risk of burns
Read the operating instructions!
ESD-compatible design and ESD-compatible workstation
CE mark of conformity
British Conformity Mark

Disposal

Do not dispose of electric tools together with household waste material! In observance of European Directive 2012/19/EU on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

Disposal – UK

Do not dispose of electric tools together with household waste material! In observance of British
Directive 2013 No. 3113 on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.