kogan ELSTANDMWWA Standing Manual Desk User Guide

USER GUIDE

STANDING MANUAL DESK
ELSTANDMWWA, ELSTANDMNWA, ELSTANDMBBA

SAFETY & WARNINGS

Ensure to read all instructions and warnings in this user guide prior to assembly and first use.
Retain this user guide for future reference.

• There are small parts included in this package that may cause a choking hazard if swallowed by accident. Keep the package out of the reach of children.
• This desk can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the desk in a safe way and understand the hazards involved.
• The maximum load capacity of this desk is 50kg.
• Throw the plastic packaging away after assembling as the plastic bags used may lead to a choking hazard for children.
• Do not allow children to play with the desk as this may lead to potential injuries.
• Children must not perform cleaning and user maintenance without supervision.
• Keep the original box in the case for future transportation.

COMPONENTS LIST

WARNING: The drawings below are only for guidance and they may differ slightly from the product and fittings received.

Hardware

OVERVIEW

ASSEMBLY

Step 1: Insert the transmission rod (10) into the holes of the gear boxes on the left and right columns (3, 4). It is fully inserted once the retainer rings on the transmission rod (10) touch the gear boxes.

Step 2: Align the holes of one metal beam (6) with the left and right columns (3, 4). Place a washer (G) and spring washer (H) over one hole. Using the 4×4 Allen key (E), secure the washers (G, H) with a 12mm M6 screw (B). Repeat this process with the three remaining holes on the metal beam.
Repeat the whole process with the other metal beam.

Step 3: Align the holes of the supporting plates (2) with the left and right columns (3, 4).
Using the 4×4 Allen key (E), secure each supporting plate (2) with two 12mm M6 screws (B).

Step 4: Align the holes of the feet (5) with the bottom of the left and right columns (3, 4).
Using the hex end of the 5×5 Allen key (F), secure each foot (5) with four 35mm M6 screws
(C). This completes the frame assembly.

Step 5: Insert dowels (D) to connect the tabletop halves (1). This creates the tabletop.

Step 6: Using the Phillios end of the 5×5 Allen key (F), secure the tabletop to the frame assembly with ST4.2 screws (A).

Step 7: Using the Phillips end of the 5×5 Allen key (F), remove the two screws on the right column. Cover and secure the hexagonal sleeve (7) onto the hexagonal shaft on the right column (4) with the two screws.
Using the same end of the 5×5 Allen key (F), secure the crank holder connector (8) to the tabletop with ST4.2 screws (A).
Insert the crank (9) through the crank holder connector (8) and hexagonal sleeve (7).

Step 8: Using the Phillips end of the 5×5 Allen key (F), secure the crank holder (11) to the tabletop with ST4.2 screws (A). Place the crank (9) onto the crank holder (11).

OPERATION

Pull out the crank from the crank holder and wind it to adjust the height of the desk. Once the desired height is reached, push the crank back under the tabletop and allow it to sit on the crank holder.

SPECIFICATIONS

Disposal

This marking indicates that this appliance should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.

Need more information?
We hope that this user guide has given you the assistance needed for a simple set-up.
For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>