ZOSI 8MN-211B4S-10 Anlapus DVR System User Manual
- June 8, 2024
- ZOSI
Table of Contents
ZOSI 8MN-211B4S-10 Anlapus DVR System
System Introduction
DVR
Camera
- Drill holes on the wall according to the mounting template, insert wall plugs into the holes.
- Align the mounting hole of the camera with the wall plugs, and then tighten screws into the wall plugs.
- Loosen the bracket screw and adjust the camera to a proper angle.
- Align the neck support of the camera with the mounting base, loosen the locking ring on the base, rotate the neck support to a proper angle, and then tighten the locking ring.
- A: Rotate the mounting base counterclockwise to separate the mounting base from the camera base.
- B: Remove the camera base.
- C: Remove the dome camera and its cover.
- D: Drill holes on the wall according to the mounting template, insert wall plugs into the holes, and then install the mounting base on the ceiling or wall with screws tightened into the wall plugs
- E: Install the dome camera and cover to the mounting base.
NOTE: Pass the cable through the mounting base before it is fixed.
System Connection
- Connect camera to NVR via BNC cable.
- Connect monitor to NVR via HDMI cable or VGA cable.
- Connect NVR to router via Ethernet cable.
- Connect mouse to USB port on NVR, then power on NVR and cameras.
View on App
Connect NVR to Internet
- A: How to connect NVR to internet?
- B: How to test the network status of NVR?
1. Right click Mouse> Main Menu> Setup> Network.
2. Check “Obtain an IP Address Automatically”.
3. Click “Test”, if it shows “OK”, indicating that NVR is connected to network. NOTE: Please make sure that the DHCP of the router is enabled.
Download Anlapus App
Run the App
- A: Install free Anlapus App.
- B: Click Register and enter your email box to get verification code.Set a password, tap Register to finish registration.
- C: Login the App, get into the main interface (My Device), click”+” icon in the upper right corner and tap Add device.
- D: Select DVR.
- E: Scan the QR code on DVR or manually enter the device ID.
- F: It will automatically jump to the device list and you can start live view.
View on PC Client
AVSS client can be applied to DVR/NVR/IPC monitoring, with functions such
as live view, device management, and remote video playback etc .. Make sure
that the device has completed the network configuration before adding device
on PC client.
Download and install the AVSS client. Official Download:
www.anlapus.com.
Login
Install and open AVSS client, select the language and click Login.
NOTE: Please register first if you don’t have an account. It is
recommended to log in with the account of An la pus App to avoid multiple
accounts, or choose local login (no account and password is required).
Device Management
Click Add Device below the device list to add device information.
Select device type: NVR/DVR/IPC, etc., enter device name, device ID or instant identifier ID {Drag the device QR code or sharing code into the QR Code Identification Zone), user name, device password and channel amount, and save the information.
NOTE: The default user name is “admin”, the default password of IPC is
“admin”, NVR/DVR does not need to enter a password, the number of camera
channels should be the number of cameras, the default is “l”.
Live View
Select the device on “Live” page and watch live streaming.
Video Playback
Select device, channel, date and time on “Playback” page, click the play icon
to start replaying recorded footage.
Recording
You can quickly start/stop recording by Right click the mouse and click Start
Recording. Right click the mouse> enter the Main Menu> Setup> Record.
Scheduled Recording
Scheduled recording is to set specific recording time period for each channel.
Right click the mouse> enter the Main Menu>Setup> Schedule.
There are 2 methods to set recording schedule.
- A:
- Use this tool to select the grid of related recording time.
- Use the eraser tool to erase the grid of the selected time. The set schedule can be copied and applied to any or all other channels by Apply settings below.
- B:
- Set the time period by double-clicking the grid area.
- The scheduled recording time created by this method can be accurate to the minute, and the set time can also be copied to other dates and channels by Apply settings.
Video Playback
Right click the mouse> enter the Main Menu> Search data, as shown in the
figure below:
Select the time and search, click Play to playback.
- Play the last video
- Play the next video
- Adjust the speed of video playback, 2x, 4x, 8x, 16x, 1/2 and 1/4x speed.
- The video can also be rewinded at 8x, 16x, and 32x speed. support single-channel display and multi-channel display. You can select one channel for full-screen viewing or multi-channel simultaneous viewing.
- Digital Zoom: click to zoom in
- Quick Backup: click to quickly enter the backup interface
Video Backup
- Insert the USB drive into the USB port of the recorder.
- Right click the mouse> enter the Main Menu> backup> select channel and time> Search>tick the video clips for backup> click Backup and wait a while to complete backup.
Alarm Settings
Motion Detection
Enable motion detection, the video recorder will only record when it detects a
moving object. Right click the mouse> enter the Main Menu> Configuration
Management> Alarm Config > Motion Detection After enabling motion detection,
the system starts recording when a moving object is captured by the camera. A-
logo will appear in the lower left corner of screen.
Select camera: All selected by default, no need to select manually.
Area setting: Set the motion detection zone and sensitivity.
Setup as follows:
Click or drag the mouse to select or erase the detection area.
- Click the star icon to set the entire field of view as a sensitive area.
- Click to save settings
- Click to log out
- Click the trash icon to clear the current detection area.
The sensitivity index ranges from 1 to 8. The default sensitivity is 6. The lower the value, the more sensitive. The higher the value, the less sensitive. Note: It is best not to have flags, trees or other objects that a re easy to flutter in the wind in the grid for motion detection to avoid false alarms.
PIR detection (for cameras with RIP detection function)
Enable Pl R detection, the recorder will only record when it detects an object
at around 37°C. Right-click the mouse> enter the Main Menu> Configuration
Management> Alarm Config> PIR When the camera captures an object at around
37°C, the system starts to record and a – logo will appear in the lower left
corner of screen.
Holding Time: The length of time that the camera keep recording after no
event is detected.
Trigger: When the device triggers an alarm, you can turn on/off the DVR’s
buzzer alarm or set up email notification in the alarm processing settings.
PIR Schedule: Set the time schedule for PIR detection (same as recording
plan setting).
PIR function is fully turned on only when motion detection and PIR detection
are turned on at the same time. When a logo appears in the lower left corner
of the monitoring screen, it means that motion detection and PIR detection are
triggered at the same time, indicating that the camera has captured movement
of object at about 37°C.
- A- logo appears when only motion detection is triggered.
- A-logo appears When only PIR detection is triggered.
- A-logo appears when motion detection and PIR detection are triggered at the same time.
Hard Drive Installation
NOTE: Please skip this step if your video recorder does not need to
replace the hard drive.
- Power off the recorder and open the side cover.
- Insert the hard drive into the DVR in the direction as shown in the figure.
- Flip over the DVR and use a Phillips screwdriver to fix the hard drive.
- Close the side cover of the DVR.
NOTE: After installation, please format the hard drive before recording .. Right click the mouse> enter the Main Menu> Disk Management> select hard drive> click Format> Apply.
FAQs
-
Q: Why can’t my device connect to the Internet?
A: Please check- Is the connected network work normally?
- Is the router working properly?
- Is the DHCP protocol of the router enabled?
-
Q: Why can’t I search for video files?
A: Please check- Does the hard drive work normally?
- Is the search time valid?
- Is the system time correct?
-
Q: Why can’t some channels be displayed?
A: Please check- Is the camera plugged in?
- Is the camera connected to DVR?
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>