homematic IP Adapter Feller Instruction Manual
- June 8, 2024
- homematic
Table of Contents
homematic IP Adapter Feller
Read the manual carefully and keep it in a safe place.
- Attention! This indicates a hazard.
- Additional important information.
All manufacturer and product names used in these instructions are only used to identify the products and may be registered trademarks or trademarks of the respective manufacturers.
Device overview
- Screws for fixing to the mounting plate
- Screw holes for fixing to the Switch Module for brand switches
Installation overview
- Please observe the safety instructions on the back side!
- When installing the Homematic IP Switch Module for brand switches, please observe the operating instructions for the device.
- integration in the EDIZIOdue switch series
- Cut the two bars on the intermediate frame flush with the frame using diagonal pliers.
Function
The Homematic IP Feller Adapter allows you to integrate your Homematic IP
system easily and conveniently into the Ediziodue switch system from Feller.
Offering an intelligent solution for your switch system, the adapter can be
attached to a Homematic IP Switch Module for brand switches (e.g. HmIP-BSM-I)
in just a few steps.
Adapters for different switches enable switches from popular manufacturers to
be replaced cost effectively with an intelligent Homematic IP installation.
The design, colour and finish of already installed switches remain the same
since existing frames and rockers can continue to be used. A separate list on
the adapter’s compatibility with standard switch series can be found in the
website download area www.homematic-ip.com.
Hazard information
Observe the following safety instructions:
- Do not open the device. It does not contain any parts that can be maintained by the user. In the event of an error, have it checked by a specialist.
- For safety and licensing reasons (CE), unauthorized change and/or modification of the device is not permitted.
- Device for indoor operation: Only operate in a dry, dust-free environment and do not expose it to moisture, vibrations, sunlight/heat radiation, cold or mechanical loads.
- The device is not a toy; Do not allow children to play with it. Do not leave packaging material lying around. Plastic films/bags, pieces of polystyrene, etc. can become a dangerous toy.
- No liability for damage to property or personal injury caused by improper use or the failure to observe the hazard information. In such cases, claim under warranty is extinguished! No liability for consequential damage!
- Do not use the device if there are signs of damage, e.g. to the housing, or if it demonstrates a malfunction. If in doubt, have it checked by a specialist.
- Only intended for use within residential, business and commercial areas as well as in small enterprises.
- Any use other than that described in the operating manual does shall invalidate any warranty or liability.
For technical support, please contact your specialist dealer.
Information on the installation
The device may only be installed in the following commer-cially available switch boxes (device boxes):
- Agro flush-mounting back boxes
- The device may only be operated with the corresponding switch covers.
- Please note! Only to be installed by persons with the relevant electro-technical knowledge and experience!*
Incorrect installation can put your own life at risk and the lives of other users of the electrical system. Incorrect installation also means that you are running the risk of serious damage to property, e.g. because of a fire. You may be personally liable in the event of injuries or damage to property. Contact an electrical installer!
- Specialist knowledge required for installation: The following specialist knowledge is particularly important during installation:
- The “5 safety rules” to be used: Disconnect from mains; Safeguard from switching on again; Check that system is deenergised; Earth and short circuit; Cover or cordon off neighbouring live parts;
- Select suitable tool, measuring equipment and, if necessary, personal safety equipment;
- Evaluation of measuring results;
- Selection of electrical installation material for safeguarding shut-off conditions;
- IP protection types;
- Installation of electrical installation material;
- Type of supply network (TN system, IT system, TT system) and the resulting connecting conditions (classical zero balancing, protective earthing, required additional measures etc.).
Maintenance and cleaning
The device does not require you to carry out any maintenance. Enlist the help of an expert to carry out any repairs. Clean the device using a soft, lint- free cloth that is clean and dry. Do not use any detergents containing solvents, as they could corrode the plastic housing and label.
Technical specifications
- Device short name
- Installation
- Degree of protection
- Ambient temperature
- Dimensions (W x H x D)
- Weight
- Subject to technical changes.
Bevollmächtigter des Herstellers: Manufacturer’s authorised representative: Mandataire du fabricant : eQ-3 AG Maiburger Straße 29 26789 Leer/Germany www.eQ-3.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>