homematic IP Wall Thermostat with Humidity Sensor Instruction Manual

: June 3, 2024
: Homematic IP

Table of Contents

homematic IP Wall Thermostat with Humidity Sensor
Device overview
Function
Notes for mounting on a flush-mounted box
Declaration of conformity
Technical specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

homematic IP Wall Thermostat with Humidity Sensor

Homematic IP Wall Thermostat with Humidity Sensor
Installation and brief instructions

Read the manual carefully and keep it in a safe place.

Attention! This indicates a hazard.
Additional important information.

Observe the safety information in the supplement „Safety instructions and general information“

Detailed manuals for

Device overview

homematic-IP-Wall-Thermostat-with-Humidity-Sensor-
fig-3

Clip-on frame
Electronic unit (thermostat)
Display
System button (teach-in button and LED)
Control wheel
Mounting plate

Connect device to

Homematic IP Access Point (Cloud)

Central Control Unit
Teach-in HmIP device

Mounting the wall thermostat

Adhere – with supplied clip-on frame
Screwing on – with supplied interchangeable frame
Screwing on – with supplied interchangeable frame
Screwing on – with supplied interchangeable frame

Set-up system:

In conjunction with a floor heating actuator directly on the control wheel of the wall thermostat
Homematic IP Access Point (Cloud)
Central Control Unit

Function

This device is part of the Homematic IP smart home system and works with the Homematic IP radio protocol. All devices of the Homematic IP system can be configured comfortably and individually with a smartphone via the Homematic IP app. Alternatively, you have the option of operating Homematic IP devices via the CCU3 or in conjunction with many partner solutions. The available functions provided by the system in combination with other components are described in the Homematic IP User Guide. The Homematic IP Wall Thermostat offers time-controlled regulation of floor heating systems in connection with Homematic IP Floor Heating Actuators or conventional radiators using Homematic IP Radiator Thermostats according to individually tailored heating phases. Temperature and humidity in the room are measured cyclically so that the room temperature can be precisely controlled. Mounting and removal are particularly easy using the clip-on frame supplied. It is also possible to integrate the wall thermostat into existing switches. All current technical documents and updates are provided at www.homematic-ip.com.

Caution! There is a risk of explosion if the battery is not replaced correctly. Replace only with the same or equivalent type. Never recharge non- rechargeable batteries. Do not throw the batteries into a fire. Do not expose batteries to excessive heat. Do not short-circuit batteries. Doing so will present a risk of explosion.Contact with batteries that are dead or damaged can cause skin irritation. Use protective gloves in this case.

When selecting the installation location, check for electrical wires and power supply cables.

Notes for mounting on a flush-mounted box

If the device is mounted to a flush-mounting box, there may be no open conductor ends.
If changes or works have to be made on the house installation (e.g. extension, bypass of switch- or socket inserts) or the low-voltage distribution for mounting or installing the device, the following safety instruction must be considered:
Please note! Only to be installed by persons with the relevant electro-technical knowledge and experience!*

Incorrect installation can put your own life at risk and the lives of other users of the electrical system. Incorrect installation also means that you are running the risk of serious damage to property, e.g. because of a fire. You may be personally liable in the event of injuries or damage to property. Contact an electrical installe

* Specialist knowledge required for installation: The following specialist knowledge is particularly important during installation:

The “5 safety rules” to be used: Disconnect from mains; Safeguard from switching on again; Check that system is deenergised; Earth and short circuit; Cover or cordon off neighbouring live parts;
Select suitable tool, measuring equipment and, if necessary, personal safety equipment;
Evaluation of measuring results;
Selection of electrical installation material for safeguarding shut-off conditions;
IP protection types;
Installation of electrical installation material;
Type of supply network (TN system, IT system, TT system) and the resulting connecting conditions (classical zero balancing, protective earthing, required additional measures etc.).

Declaration of conformity

eQ-3 AG, Marburger Straße 29, 26789 Leer, Germany hereby declares that the radio equipment type Homematic IP HmIP-WTH-1 is compliant with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at www.homematic-ip.com