LEEDARSON

NA Smart Plug(Z-Wave)

SKU: 6A-PL-VAB-A0

Quickstart

This is a
secure
On/Off Power Switch
for
U.S. / Canada / Mexico.

To run this device please connect it to your mains power supply.

To add this device to your network execute the following action:
To add the product to the Z-Wave network:a. Make sure that the Smart Plug has been connected to the power supply.b. Set the Z-Wave network main controller into inclusion mode.c. Power on.d. The LED will blink fast until the inclusion is completed and then the LED will keep turning on or off. Otherwise, the LED will still blink slowly, in which you need to repeat the process from step b

Please refer to the
Manufacturers Manual for more information.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message ( two- way
communication) and every mains powered node can act as a repeater for other nodes
( meshed network ) in case the receiver is not in direct wireless range of the
transmitter.

This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.

If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.

Product Description

Smart Plug can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.Smart Plug is also a security Z-Wave device and supports the Over The Air (OTA) feature for the products firmware upgrade.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This
procedure should only be used when the primary controller is inoperable.

Reset Smart Plug to factory default:1. Make sure that the Smart Plug has been connected to the power supply.2. Press and hold the Button for 5 seconds.3. If holding time is more than one second, the LED will blink faster and faster. If holding time is more than 5 seconds, the LED will be solid for 3 seconds to indicate that the resetting is successful. Otherwise, repeat step 2.Note:Reset to factory will remove Smart Plug from the Z-Wave network. Use this procedure only in the event that the network primary controller missing or otherwise inoperable.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country- specific
installation guidelines/norms may do works with mains power. Prior to the assembly of
the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.

Inclusion

To add the product to the Z-Wave network:a. Make sure that the Smart Plug has been connected to the power supply.b. Set the Z-Wave network main controller into inclusion mode.c. Power on.d. The LED will blink fast until the inclusion is completed and then the LED will keep turning on or off. Otherwise, the LED will still blink slowly, in which you need to repeat the process from step b

Exclusion

To remove the product from the Z-Wave network:a. Insert the Smart Plug to power socket, the LED will follow the status (on or off) of its loads power level.b. Set the Z-Wave network main controller into exclusion mode.c. Short press Button 3 times within 1.5 second.d. The LED will blink fast until the exclusion is completed, then the LED will keep on blinking slowly. Otherwise, the LED will keep on blink fast for 35 seconds and then follow the status (on or off) of its load status.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

1| 5| 1. When the state of Smart Plug (turn on or off the load) is changed:1. Set Configuration parameter 0x03 to 0: Do not send Basic Report2. Set Configuration parameter 0x03 to 1: Send Basic Report3. Set Configuration parameter 0x03 to 2: Send Basic Report only when Load condition is changed not by Z-WAVE Command, such as short pressing.2. Sending Meter Report.
---|---|---

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock further
enhanced features.

IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56.
In case of a two byte value the same logic applies: Values greater than 32768 may
needed to be given as negative values too.

Parameter 1: Overcurrent protection

Smart Plug keep detecting the load power, once the AC current exceeds 16.5A for more than 4 seconds, smart plug’s relay will turn off.
Size: 1 Byte, Default Value: 1

SettingDescription

Parameter 100: Setting the parameters 101~104 to the default states.

Setting the parameters 101~104 to the default states.
Size: 1 Byte, Default Value: 85

SettingDescription

Parameter 101: Setting time for sending meter report (watt)

The interval time of sending meter report (watt) to associated device (Group Lifeline).
Size: 4 Byte, Default Value: 600

SettingDescription

Parameter 102: Setting time for sending meter report (KWh)

The interval of sending meter report (KWh) to association device (Group Lifeline).
Size: 4 Byte, Default Value: 3600

SettingDescription

Parameter 103: Setting time for sending meter report (voltage)

The interval of sending meter report (voltage) to association device (Group Lifeline).
Size: 4 Byte, Default Value: 0

SettingDescription

Parameter 104: Setting time for sending meter report (current)

The interval time of sending meter report (current) to associated device (Group Lifeline).
Size: 4 Byte, Default Value: 0

SettingDescription

Parameter 16: The value here represents minimum change in wattage (in

terms of wattage) for a meter report to be sent

When the change value of load power exceeds the setting value, smart plug will send meter report (watt) to associated device (Group Lifeline).
Size: 2 Byte, Default Value: 50

SettingDescription

Parameter 17: The value here represents minimum change in wattage percent

(in terms of percentage) for a meter report (watt) to be sent

When the change value of the load power exceeds the setting value, smart plug will send meter report to associated device (Group Lifeline).
Size: 1 Byte, Default Value: 10

SettingDescription

Parameter 2: Setting device status after power failure

Define how the Plug reacts after the power supply is back on.
Size: 1 Byte, Default Value: 0

SettingDescription

device will be on after the power supply is reconnected.
2| Smart Plug does not memorize its state after a power failure. Connected device will be off after the power supply is reconnected.

Parameter 254: Enable/disable the configuration command

Lock/unlock all configuration parameters.
Size: 1 Byte, Default Value: 0

SettingDescription

Parameter 3: Notification when Load status change

mart Plug can send notifications to associated device (Group Lifeline) when the status of smart plugs load is changed.
Size: 1 Byte, Default Value: 1

SettingDescription

Parameter 4: LED Load indicator mode selection

Configure LED Display mode to prevent light pollution at night.
Size: 1 Byte, Default Value: 0

SettingDescription

Technical Data

Supported Command Classes

• Association Grp Info
• Association V2
• Basic
• Configuration
• Device Reset Locally
• Firmware Update Md V4
• Manufacturer Specific V2
• Meter V3
• Powerlevel
• Scene Activation
• Scene Actuator Conf
• Security
• Security 2
• Supervision
• Switch Binary
• Transport Service V2
• Version V2
• Zwaveplus Info V2

Explanation of Z-Wave specific terms

• Controller — is a Z-Wave device with capabilities to manage the network.
  Controllers are typically Gateways,Remote Controls or battery operated wall controllers.

• Slave — is a Z-Wave device without capabilities to manage the network.
  Slaves can be sensors, actuators and even remote controls.

• Primary Controller — is the central organizer of the network. It must be
  a controller. There can be only one primary controller in a Z-Wave network.

• Inclusion — is the process of adding new Z-Wave devices into a network.

• Exclusion — is the process of removing Z-Wave devices from the network.

• Association — is a control relationship between a controlling device and
  a controlled device.

• Wakeup Notification — is a special wireless message issued by a Z-Wave
  device to announces that is able to communicate.

• Node Information Frame — is a special wireless message issued by a
  Z-Wave device to announce its capabilities and functions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>