Innovation Perfect Enterprises PAC018 Motion Activated Dual Head Security Light with Camera Instruction Manual

Innovation Perfect Enterprises PAC018 Motion Activated Dual Head Security

Light with Camera

Model: PAC018 , PAC027

Please read all instructions thoroughly and carefully prior to installing this product. Retain these instructions for future reference.
We assumes no liability or responsibility for claims arising from improper installation or improper use. Failure to follow these instructions could result in voiding the product warranty.
IMPORTANT SAFETY INSTRUCTIONS
Before you begin installing, servicing, or maintenance of this product, follow these general precautions.

• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards please read all warnings and instructions included with and on this product prior to installation.
• For commercial installation: service and maintenance of this product should be performed by a qualified, licensed electrician.
• For residential installation: If you are unsure about the installation or maintenance of this product, consult a qualified licensed electrician.
•  Do not mount the unit against flammable surfaces.
•  This product is intended to be used outdoors, and be subject to the elements; such as rain and snow and we recommend it to be mounted at least 6’ 6” off the ground
• This LED product must be powered directly to a switched circuit.
• Make sure that where this fixture will be mounted is structurally sound and that it will support the weight of this fixture
• This product should not be used in areas with limited ventilation or high ambient temperatures.
• This product is intended to be connected to a properly installed and grounded UL listed junction box.

WARNING: RISK OF ELECTRICAL SHOCK

• Turn off electrical power at fuse or circuit breaker box before wiring product to the power supply.
• Verify voltage is 100V‐240V before installing.
• Make all electrical and grounded connections in accordance with the National Electric Code and any applicable local code requirements.
• All wiring connections should be capped with UL listed wire connectors.

CAUTION: RISK OF PRODUCT DAMAGE

•  Never connect fixture with power on.
• Do not mount or support product in a manner that can cut the outer wire jacket or damage the wire insulation.
• Avoid covering LED products with insulation, foam, or other materials that will prevent convection or conduction cooling.
• Never connect an LED product directly to dimmer packs, occupancy sensors, timing devices, or other related control devices, unless individual product specifications deem otherwise.
• LED products are polarity sensitive, ensure proper polarity before installation.
• Electrostatic Discharge (ESD) can cause damage to LED products. Wear personal grounding equipment during installation and service of the product.
• Do not touch the individual electronic components, it may cause ESD (Electronic Discharge), shorten lamp life or alter performance.

CAUTION: RISK OF INJURY

• Wear gloves and safety glasses at all times when removing fixture from carton, installing or servicing the product.
• Avoid direct eye exposure to the light source while it is on.
• LED LIGHTS ARE EXTREMELY BRIGHT, UNDER NO CIRCUMSTANCES SHOULD YOU  LOOK  DIRECTLY  INTO  AN  LED LIGHT, THIS MAY CAUSE IRREPARABLE DAMAGE TO THE EYES.
•  Please dispose of packaging materials and account for all small parts as these can be hazardous to small children.

WARNING: RISK OF BURN

• Allow fixture to cool completely before handling.
• Do not exceed maximum voltage marked on the label.
• Keep combustible and other materials that can burn away from the light, lamp, and lens.

Specfications

Maximum1.80degree,10m

Lumen| 2600lm
Colour temperature| 3000k
Reording resolution| 1080p
Clouding Reconrding| Yes
Local Recording| Yes
Micro SD card| Yes(not includes)
Waterproof| IP55

Installation Instructions

Note: this fixture can be wall or eave mounted

Silicon Sealant recommended (not included)
Tools Required for Installation: Phillips screwdriver, level

MOUNTING AND WIRING THE LIGHT

NOTE: DO NOT MOUNT ON THE GROUND, RECOMMENDED INSTALLATION sHEIGHT IS 6 ½ FEET TO 10 FEET Before you begin make sure that your power is turned off at your circuit breaker box
Do not rely on the switch power being turned off **

ADJUSTING YOUR LIGHT HEADS

Your light heads can be adjusted by turning the individual light head to desired position. You can also adjust your light head up and down to your desired position.

Indicator light

Note: Fixture can be wall mounted or eave mounted.

(Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation).

APP User guide

Setting light through mobile device.Search”Guard 720”or “Swann security “in IOS APP store or in Android Google play.Install the”Guard 720” or” Swann security “App onto the device.(Take Guard 720 as an example)

1. • Register a new account:
     

2. 

3. 

TROUBLE SHOOTING

If the light does not come on:

•  Verify the power is turned on at the switch and breaker
• Verify that the product is properly wired
• Verify that the line voltage is correct (100V‐240V)

If the manual override stays on after dawn

• The ambient light lever may be too low (not enough light)

FCC WARNING
Any Changes expressly or modifications not approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:

• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
• This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter.
• This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

ISEDC RSS WARNING
This device complies with ISEDC licence‐exempt RSS standard (s).Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
ISEDC RADIATION EXPOSURE STATEMENT

• This equipment complies with ISEDC RF radiation exposure limits set forth for an uncontrolled environment.
• This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter.
• This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>