RH TEEN TL1058 Textured Metal Task Table Lamp with Wireless Charging Instruction Manual
- June 6, 2024
- RH TEEN
Table of Contents
RH TEEN TL1058 Textured Metal Task Table Lamp with Wireless Charging
PARTS ENCLOSED
(A) Plug (1)
(B) Lamp base (1)
(C) Charging pad (1)
(D) LED bulb (1, included)
(E) Lamp shade (1)
(F) ON/OFF rotating switch (1)
IMPORTANT SAFETY INSTRUCTIONS
For safety purposes, this lamp is equipped with a polarized plug (one blade is wider than the other). If the plug does not fit securely into your outlet, do not force it contact a professional electrician. Use the plug with an extension cord only if it can be fully inserted into the cord’s socket. Never alter the plug in any way.
This lamp has been rated for up to (1) 4w max LED bulb ( included). To avoid the risk of fire, do not exceed the recommended wattage.
WARNINGS
All wires are connected. When unpacking, be careful not to pull wires, as a
bad connection may result. Do not connect electricity until your lamp is fully
assembled. To reduce the risk of fire, electrical shock, or personal injury,
always turn off and unplug lamp and allow it to cool prior to replacing
lightbulb. Do not touch the bulb when lamp is turned on. Keep flammable
materials away from lit bulb.
THIS PRODUCT IS NOT A TOY AND HAS NO PLAY VALUE.
WARNING: STRANGULATION HAZARD
Keep cord at least 3 feet away from cribs, bassinets, and toddler beds.
Keep out of reach of children under 3 years of age.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for
Class B digital devices, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on. The user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ASSEMBLY & INSTALLATION
- Carefully remove all parts from the box and remove plastic coverings.
- Carefully place the lamp base (B) on a tabletop.
- Insert the LED bulb (D) into the socket and secure tightly.
- Insert plug (A) into proper electrical outlet and turn the ON/OFF rotating switch (F) to test the lamp.
- Push the lamp shade (E) slightly forward and back about 45 degrees to adjust the shade angle, but don’t push too far to avoid damaging or twisting the cord.
- If a cell phone needs to be charged, place on the charging pad (C).
- Assembly is complete.
CARE INSTRUCTIONS
- Wipe clean with a soft, dry cloth.
- Do not use polishes or cleaners, as they may damage the finish.
TEXTURED METAL TASK TABLE LAMP WITH WIRELESS CHARGING – ASSEMBLY INSTRUCTIONS
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.
This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>