SWIT PL-E90L Edge Mounted SMD Panel LED Light User Manual

PL-E90L Edge Mounted SMD Panel LED Light
User Manual

Thank you for choosing SWIT products, please read this user manual carefully and save it for future reference.

Specification

Caution

1. Please do not disassemble the light or touch its inner part with a metal object to avoid damage;
2. Please do not put the light under conditions full of moisture or dust to avoid damage;
3. The USB port is reserved. Use it according to the specific environment of the company’s related products. Do not use it for another purpose to avoid losses;
4. Please do not connect any DMX output device with light when using interaction control, otherwise, interaction control function will not be used normally.
5. Only use the light in the temperature range of -10C40°C.

Maintenance

1. Please clean the front LED panel with a soft dry cloth. If using a soft cloth with a slightly clean neutral detergent solution, please wipe again with a soft dry cloth.
2. Do not use wet cloth, anhydrous alcohol, gasoline, or a mixture of anhydrous alcohol and ether, etc. to wipe the front LED panel.

Dimension

Appearance

LCD display

For example:PL-E90L,color temperature 5600K,dimmer 100%,powered by fully charged battery:

1. Current communication control mode
   – DMX communication mode

2. Current communication control mode
   – interaction control mode

3. Brightness display

4. Communication address

5. CT display

6. Power supply display(AC adaptor power supply)

7. Power supply display( battery power supply)

Note: When powered by battery, the battery capacity will be displayed as below:

Accessories Installation

Fig.6 is the installation pattern of a barn door, pay attention that the round screws need to upward when installing the barn door.

Usage

1. Installation
   1.1 Accessories Installation
   For the installation of a barn door, please see Fig.6 [Barn door installation] a
   1.2 User can install the light on a tripod or stand, and adjust demanded casting angle by a knob on both sides of the U-stand.

2. Power supply
   This light can be powered by a battery or AC adaptor.
   2.1 Battery installation

1. Installation
   Connect the battery with the battery plate,(Fig.4 (14), hear the “Click” sound to complete the battery installation.
2. Remove
   Push the lock rod(Fig.4 (4)to remove the battery from the plate.
   2.2 The connection and disconnection of the AC adaptor
3. Connection
   Align the hump of the output male XLR to the gap of the DC socket, connect XLR and DC socket, the adaptor will connect with the light when you hear the “Click”  sound.(Polarity:pin1″-“;pin4″+”)
4. Disconnection
   Hold the hump of the DC output female XLR and pull out, the power adaptor and the light will be disconnected.

3. Dimmer and color temperature setting
   The light provides two ways of adjusting the color temperature and brightness: normal adjusting mode and quick adjusting mode. Users can switch the adjusting mode by press the dimmer knob and color temperature adjusting knob(Fig.4 10/12). User can quickly set the dimmer and color temperature to their needs by combining two adjusting modes.
   3.1 Normal adjusting mode

1. Color temperature adjusting Range:2700K-6500K, adjust steps:S0K
2. Dimmer adjusting
   Range:0%-100%, adjust steps:1 %
   3.2 Quick adjusting mode
3. Color temperature adjusting
   Under this mode, the user can quickly choose common color temperature:2700K, 3200K,4500K,5600K,6500K
4. Dimmer adjusting
   Range:0%-100%, adjust steps:10%

4. The setting and usage of communication address
   Hold the brightness adjust knob(Fig.4 10)for 2s to enter in the setting interface of communication address, communication address setting ra nge:001-512.
   The chosen number will show a flashing backlight, turn the brightness adjust knob(Fig.4 10) left and right to set the current number, press the brightness to adjust knob(Fig.4 10)to confirm the current number and set the next number, after finishing setting the last number, press brightness adjusts knob(Fig.4 10)or wait for about Seconds to exit communication address setting.

5. The setting and usage of communication control mode
   Connect all the lights with the DMX cable, and hold the color temp adjust knob (Fig.4 2) about 2s to complete the setting of communication mode.
   5.1 DMX Communication mode
   The top left corner of the LCD screen shows “DMX” (Fig.5 CD) indicating that the communication control mode currently is DMX communication mode. In this mode,  connect the DMX signal output device to the lights network, and set up the communication address to work normally.
   This light occupies 2 DMX control channels, the current DMX address(N) is brightness control, and the next set address of the current value (N+1) is color temperature control.
   For example: DMX Communication address| DMX Control address| Function
   ---|---|---
   5| 5| Brightness 0%400%
   6| Color temperature 2700K-6500K

5.2 Interaction Control Mode
The top left corner of the LCD screen shows “CH” (Fig.5 2) indicating that the communication control mode is interaction control mode. In this mode, set the target lights to the same communication address to work normally, and the master-slave machine is not distinguished.
Tips: Please do not connect any DMX output device with light when using interaction control, otherwise interaction control function will not be used normally.

6. USB Socket
   The USB socket is reserved. Use it according to the specific environment of the company’s related products. Do not use it for another purpose to avoid losses;

Packing List

Note:

1. Package 1: Single light package (with barn door)
2. Package 2: Three lights kit

Tel:-+86-25-85805753
Fax:+86-25-85805296
http://www.swit.cc
E-mail: contact@swit.cc

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>