SWIT WAVE500 Wireless Microphone User Manual
- June 2, 2024
- SWIT
Table of Contents
Model: WAVE500
Wireless Microphone
User Manual
WAVE500 Wireless Microphone
Please read this user manual throughout before using
Ver: A
WARRANTY CERTIFICATE
Please register y o u r warranty. Meanwhile, you are welcomed to contact us
via Email: contact@swit.cc
USER INFORMATION
| Customer Name:
---|---
Phone Number:
Email:
Address:
SALES INFORMATION| Sales Date:
Model:
Product Code:
Dealer:
REPAIR RECORD| Service Date:
Technician:
Issue:
RESULT| Solved| Unsolved| **** Returned(Replaced)
Caring For Your SWIT Product
- Please keep the product in a dry, clean, dust-free environment.
- Keep corrosive chemicals, liquids and heat source away from the product to prevent mechanics damage.
- Use only a soft and dry cloth for cleaning the product.
- Malfunction may be caused by dropping, impact of external force.
- Do not attempt to disassemble the product. Doing so voids warranty.
- Please hav e the product checked or repaired by authorized technicians if any malfunctions happened.
- Failure t o follow all the instructions may result in mechanics damage.
- Warranty does not apply to human errors.
Package List
R X Receiver x1
|
TX Transmitter x2
|
Carrying Bag x1
|
Mic Windshield x2
---|---|---|---
Eject Pin x1
3-in-1 Charging Cable x1
|
External Lav Mic (With Wind Muff) x2
3.5mm TRRS Phone Cable x1
|
3.5mm TRS Camera Cable x1
Product Instruction
TX Transmitter
1. External Mic Input
2. USB-C Port
3. Power (MUTE)
4.Reset(Help with Eject Pin)
5. Low Cut| 6. Pairing
7. Built-in Mic
8. Display Screen
9. Pocket Clip
---|---
RX Receiver
1. USB-C Port
2. Power(Mono/Stereo)
3. Reset(Help with Eject Pin)
4. Channel A Gain Control
5. Channel B Gain Control| 6. 3.5mm Audio Output
7. 3.5mm Monitoring Jack
8. Display Screen
9. Pocket Clip
---|---
Display Screen
Operations
TX
1.Power/ Mute
Long Press 2s: turn on/off the system
Short Press: mute/unmute the microphone
2. Charging
5V/2A;with USB-C Charging Cable
Please fully charge the product before use.
3.External Mic Input
TRS Mic Only
(Note: When using a external mic, please insert it into the mic input
properly.)
4.Mic Windshield & Device Installation
5. Reset
6. Low Cut
Short Press: 150 Hz Low Cut On
Short Press again: Low Cut Off
7. Pairing
The system will pair automatically after power on.
(Note: Before success fully connecting, the transmitter channel will
display A by default. The TX connected to the receiver first is Channel A ,
and the one connected later is Channel B.)
Manual pairing: long press the Channel A Gain Control and Channel B Gain
Control on the RX and Pairing on the TX for 3 seconds at the same time
RX
1. Power/ Mono/Stereo Switch
Long Press 2s: turn on/off the system
Short Press: Switch Mono/Stereo mode (Note: Stereo mode is unavailable in
phone devices.)
2. Charging
5V/2A;with USB-C Charging Cable
Please fully charge the product before use.
3. Reset
4. Gain Control
0-5 Level(0 → 3 → 6 → 9 → 12 → 15 → 0)
Each press increases the gain of Channel A / Channel B b y one level.
5. Pairing
The system will pair automatically after power on.
Manual pairing: long press the Channel A Gain Control and Channel B Gain
Control on the RX and Pairing on the TX for 3 seconds at the same time
(Note: The first TX that successfully connects with the RX will be
Channel A . )
6. Audio Monitoring & Output Connection
Setting The Recording Level Correctly
Camera devices generally have poor-quality, noisy preamps. In order to get the
cleanest signals possible, it is highly recommended that you set the recording
level on your camera quite low, 1/2 or 1/3 of it. G2 provides variable gain
control, allowing you to tail or your levels to just about environment and
recording device.
Adjust the recording level of inbuilt mics for SONY Camera (Take A7S I I for
example)
Adjust the recording level of inbuilt mics for Canon Camera (Take EOS 5D Mark I V for example)
Adjust the recording level of inbuilt mics for Panasonic Camera (Take LUMIX GH5 for example)
Specifications
TX Transmitter
Wireless Transmission | Digital 2.4GHz |
---|---|
RF Frequency Band | 2400-2483.5MHz |
Frequency Response | 20HZ-20KHz |
Working Distance | 492ft/150m (LOS area), 164ft/50m (NLOS area) |
Mounting | Pocket Clip |
Audio Input | 1/8″ /3.5mm TRS Mic Input |
Audio Input Level | 1V (OdBV) |
Power Requirements | 3.3V-4.7V |
Battery Type | Built-in Lithium Battery, 400mAh |
Battery Charging Time | 1.5H |
Battery Life | 8H |
Display | TFT Screen |
Dimensions | 52 X42X*17mm |
Material | Plastic |
Weight | 39¢ |
RX Receiver
Wireless Transmission | Digital 2.4GHz |
---|---|
RF Frequency Band | 2400-2483.5MHz |
Approximate RF Sensitivity | -81dBm |
Working Distance | 492ft/150m (LOS area), 164ft/50m (NLOS area ) |
Mounting | Pocket Clip |
Number of Audio Channels | 2 |
Audio Output | 1/8″ / 3.5mm TRS Mic Output |
1/8″ /3.5mm TRS Headphone Output
Gain| 0-5 Level
Audio Output Level| Line Out: 1V; Monitoring: 25-30mW
Power Requirements| 3.3V-4.7V
Battery Type| Built-in Lithium Battery, 400mAh
Battery Charging Time| 1.5H
Battery Life| 8H
Display| TFT Screen
Dimensions| 52X42 17mm
Material| Plastic
Weight| 39¢
Microphone
Form Factor | Built-in/External Mic |
---|---|
Sound Field | Mono |
Polar Pattern | Omnidirectional |
F r e q u e n c y Range | 50Hz-20KHz |
Sensitivity | -40dB (+3 dB, re 1V/Pa a t 1KHZz) |
Maximum SPL | 135dB SPL (at 1KHz) |
Warranty
Warranty Period
Thank you for purchasing SWIT products.
- Customers are entitled to free replacement or repair service in case of quality defect(s) found in the product under normal use within 30 days upon receipt of the product.
- Original SWIT products are entitled to 12-month limited warranty service. The warranty period begins on the date of purchase of brand new, unused products by the first end-user.
Within the warranty period, if product defect or failure i s attributable to
material defection or technological problem, the defective product or
defective part will be repaired or replaced without charge (service and
materials fee).
Warranty Exclusions and Limitations
- Faults resulted from inappropriate use of a product without following its operation specification
- Artificial damage, e.g. crash, squeeze, scratch, or soaking
- Modifications to a product by its user or third party without prior written consent of SWIT, e.g. replacement of element or circuit, label alteration
- The code on product is inconsistent with that of warranty certificate, or the code on the product or warranty certificate is altered or torn off
- All consumable accessory attached to a product, like cable, wind muff, battery
- Faults as a result of force majeure, such as fire , flood, lightning, etc.
Warranty Claim Procedure
- If failure or any problem occurs to your product after purchase, please contact a local agent for assistance, or you can always contact SWIT customer service through email at contact@swit.cc
- Please retain your sales receipt and warranty certificate as proof of purchase. If any of these documents is missing, only sales return or chargeable service will be provided.
- If the SWIT product is out of the warranty coverage, the service and the parts cost will be charged.
SWIT Electronics Co., Ltd.
Address: 10 Hengtong Road, Nanjing Economic and
Technological Development Zone,
Nanjing 210038, P.R.China
Phone: +86-25-85805753
F a x : +86-25-85805296
Email:contact@swit.cc
http://www.swit.cc
Documents / Resources
| SWIT
WAVE500 Wireless
Microphone
[pdf] User Manual
WAVE500 Wireless Microphone, WAVE500, Wireless Microphone, Microphone
---|---