Comfort Zone CZ9010 Series Digital Oil Filled Radiator Instruction Manual
- June 4, 2024
- Comfort Zone
Table of Contents
Comfort Zone CZ9010 Series Digital Oil Filled Radiator
Digital Oil-Filled Radiator
Features:
-
Digital Thermostat
-
Auto-Off Timer
-
Three Heat Settings:
Low: 600W
Medium: 900W
High: 1,500W (5,120 BTU) -
Anti-Frost Function
-
Safety Tip-Over
Cut-Off Protection -
Fahrenheit (°F) or Celsius (°C)
-
Power Indicator Light
-
Oil Permanently Filled
-
Convenient Cord Storage
-
Durable Metal Housing
-
120V AC / 60Hz / 12.5A
INTENDED USE:
This product is intended for indoor residential and office use only, not for
industrial or other commercial application. Use only with electrical wiring
that is in good working order and that meets applicable codes and ordinances.
This heater must be plugged directly in to a 120V AC, 15 Amp (or larger)
circuit. Do not plug anything additional into the same circuit. If you have
any questions whether your wiring is adequate, consult a qualified
electrician. Risk of fire, overheating, malfunction, property damage, injury
or even death may result if not adhered to.
Use your heater only with a working smoke detector located in the vicinity of
your heater.
While using your heater, you should follow the IMPORTANT INSTRUCTIONS
listed below. As part of those instructions, we have used the word “
WARNING” to indicate the level of hazard: WARNING indicates a hazard
which, if not avoided, could result in injury or death.
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:
- Read all the instructions before using this heater.
- This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use provided handle when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 meters) from the front of the heater and keep them away from the sides and rear.
- Do not use heater unattended. Use of extreme caution is necessary when any heater is used by or near children, invalids, disabled persons or pets.
- Do not operate the heater with a damaged power cord or after the heater malfunctions, has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment or repair.
- Do not use heater outdoors.
- Use your heater only in dry environments. This heater is not intended for use in a bathroom, laundry area, or similar locations, or near sinks, washing machines, swimming pools or other sources of water. Never locate heater where it may fall into a bathtub or other water container. Do not use in damp environments such as flooded basements.
- Do not place the heater on a small, unlevel, uneven or any surface which might allow heater to tip or fall.
- For proper operation, heater should be placed on a smooth, non-combustible, level surface. Do not place on rugs, carpet, vinyl flooring or other plastic surfaces. Not for use outdoors or in wet areas.
- This heater is not designed as a primary heat source.
- Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip). Always unplug heater when not in use.
- Do not run power cord under carpeting. Do not cover cord with throw rugs, runners or similar coverings. Arrange cord away from traffic area where it will not be tripped over.
- To disconnect heater, turn controls off then remove plug from outlet.
- Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage the heater.
- To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces like a bed, where openings may become blocked.
- A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored.
Use this heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock
or injury to persons or property.
READ & SAVE THESE INSTRUCTIONS
WARNING: SHOCK HAZARD
Use your heater only in dry environments. This heater is not intended for use
in a bathroom, laundry area, or similar locations, or near sinks, washing
machines, swimming pools or other sources of water. Never locate heater where
it may fall into a bathtub or other water receptacle. Do not use in damp
environments such as flooded basements.
WARNING: HOT SURFACES
Do not touch body of heater when in use. If provided, use handles when moving
this heater. This heater is hot when in use. Do not stand directly in front of
the heater or let bare skin touch hot surfaces to avoid burns. Prolonged or
frequent exposure to a heat source may cause rashes, burns, or blistering to
the skin.
WARNING: FIRE HAZARD
Heater has hot and arcing or sparking parts inside. Do not use near
combustible materials or flammable gases or sources of heat.
DO NOT USE in areas where gasoline, paint or flammable materials are used or
stored. Keep combustible materials such as furniture, pillows, bedding,
papers, clothes and curtains at least 3 feet (0.9 m) from
the front of the heater and keep them away from the sides and rear. To prevent
a possible fire, do not block air intakes or exhaust in any manner. Do not use
on soft surfaces, like a bed, where openings may become blocked. Do not place
the heater near a bed because objects such as pillows or blankets can fall off
the bed and be ignited by the heater. Do not insert or allow foreign objects
to enter any ventilation or exhaust opening as this may cause an electric
shock, fire, or damage the heater. Always plug heaters directly into a wall
outlet/receptacle. Never use with an extension cord or relocatable power tap
(outlet/power strip). Never leave heater unattended. Always unplug heater when
not in use.
WARNING: ELECTRICAL SHOCK HAZARD
Do not use with damaged cord or plug. Use with adequate electrical system that
is up to code.
CAUTION : TO PREVENT ELECTRIC SHOCK
This product has a polarized two prong plug (one blade is wider than the
other) that must be fully inserted into a matching properly grounded outlet.
This plug is designed to fit a polarized outlet only one way. If the plug does
not fit fully into the outlet, reverse the plug. If the plug still does not
fit, contact a qualified electrician. Do not attempt to defeat this safety
feature.
Do not operate any heater with a damaged cord or plug or after heater
malfunctions, has been dropped or damaged in any manner. Do not operate heater
with a broken heating element or ceramic cone or any visual imperfections.
WARNING: Never tamper with this product or attempt to fix it. Any
tampering with, or modification of this product can result in serious injury,
death, or fire. Risk of electric shock. DO NOT open. There are no user
serviceable parts inside. For Warranty information see warranty statement. For
Warranty services contact Comfort Zone® Customer Service by telephone or mail
for information and assistance.
PET OWNERS NOTE:
The health of birds and some small pets are extremely sensitive to the fumes
given off during the initial use of many appliances. Although these fumes are
not harmful to humans, it is recommended that this heater not be used around
birds and small pets during its initial use until the manufacturing corrosion
coatings burn off.
WHEEL ASSEMBLY INSTRUCTIONS:
-
Remove the heater and all parts from the packaging box.
NOTE: Some parts may be stored in the Styrofoam packing at the bottom of the box. Remove Styrofoam packing from the box and check the underside for parts that may be stored there. -
DO NOT OPERATE THIS HEATER WITHOUT CASTER WHEELS ASSEMBLED PER THESE INSTRUCTIONS.
NOTE: It is normal for the oil to move inside the radiator when moving the product. -
Place the unit on a flat, stable surface, ensuring the unit will not tip over.
-
Remove the wing nuts from the U bolts.
-
Front caster wheel assembly: lay the caster wheel assembly across the heater over the front fin and secure with U bolt and wing nut.
-
Back caster wheel assembly: lay the caster wheel assembly over the back fin and secure with U bolt and wing nut.
-
Do not over-tighten wing nuts.
-
Place heater upright on a flat surface and ensure that it can move freely and smoothly.
-
Wait 3 minutes for oil to settle before turning on heater.
USAGE:
HEATER OPERATION : Always operate the heater in the upright position
following all instructions and recommendations listed in this manual.
HEATER LOCATION: Place the heater in the area of the room that is
coldest. Do not place near combustible materials.
HEATER CONNECTION: Plug heater directly into 120 Volts AC, 60Hz wall
outlet. Be sure plug fits tightly in outlet. A loose connection may cause
overheating and damage to the plug or heater.
NOTE: To prevent overloading a circuit, do not plug the heater into a
circuit that is servicing other electrical needs.
The heater has three heat settings: 600 Watts (LOW), 900 Watts (MEDIUM) and
1,500 Watts (HIGH). Use the 1,500 Watts setting to raise the room temperature
quickly while thermostat control is at its highest setting. (During the
heaters initial use, you may experience a slight odor or smoking. This is the
result of residual lubrication on the steel “burning off”. This is normal and
will go away after a few minutes of use.) When desired temperature is reached,
the 900 Watts setting should be sufficient to maintain a comfortable
temperature in most situations.
TURNING HEATER ON: Once plugged into an outlet, the heater is in STANDBY
mode, and the ON/STANDBY INDICATOR lights up. Touch the ON/STANDBY INDICATOR
button to start the heater.
OPERATING INSTRUCTIONS: This heater is equipped with Digital Controls
that provide the ability to set the temperature to the exact degree desired.
To operate, simply follow these instructions.
NOTE: The display will always show the set temperature and will not
display the room temperature.
NOTE: Once plugged in, the heater is in STANDBY mode and can be adjusted
to begin heating. Leave in STANDBY if you plan to use the ANTI-FROST FUNCTION.
See below.
CONTROL PANEL
MODE:
-
Touch the MODE button to switch heating modes. The heater will cycle through heat settings as you press the button.
“3” is HIGH setting, “2” is MED setting and “1” is LOW setting. -
When setting the MODE, the MODE button is highlighted and the display window will show the “3-2-1” heat setting. Once the heating mode is set, after 3 seconds the display window will change to indicate the set temperature (default temperature is 77°F).
-
At any time when the heater is on and working, touch the MODE once and the display will show the set mode. If no other adjustment action is taken after 3 seconds, the display will change to indicate the set temperature.
TEMPERATURE:
- To set temperature, press the TEMPERATURE button and then use the arrow keys to increase or decrease the temperature until you reach the desired temperature. After 5 seconds, the set TEMPERATURE will be locked in and displayed.
- Before using the arrow keys to set the temperature, you must press the TEMPERATURE button. The arrow keys will not function if the TEMPERATURE button is not pressed first.
- To switch from Celsius to Fahrenheit, press and hold the TEMPERATURE button 5 seconds. You can switch back to Celsius by pressing and holding the TEMPERATURE button again.
- In Fahrenheit mode, the default control temperature is 77°F and the temperature range is 59°F – 95°F. In Celsius mode, the default control temperature is 25°C and the temperature range is 15°C – 35°C.
NOTE: After the heater is turned off or a power outage occurs, the heater will remember whether it was in Celsius or Fahrenheit mode. There will be no need to reset this after power is cut to the heater.
TIMER:
- To activate the TIMER function, press the TIMER button and then use the arrow keys to set run time in 1 hour increments from 0H to 17H.
- After 5 seconds, the TIMER setting will be locked in and displayed for another 3 seconds. After that, the display will default to the set TEMPERATURE.
NOTE: If TIMER is activated, when the heater is turned off or a power
outage occurs, the heater will not remember the desired TIMER setting. The
TIMER will have to be reset after power is cut to the heater.
ANTI-FROST FUNCTION: To use the Anti-Frost feature the heater must be in
STANDBY mode.
- If the room temperature is below 41°F (5°C), the ON/STANDBY INDICATOR light will flash and the display temperature will flash 45°F continuously. The heater will automatically start heating on the MED setting.
- Once the room temperature is above 45°F (7°C) the display will turn dark and all flashing stops. The heat will turn off and the heater returns to STANDBY mode.
NOTE: This process will repeat to keep the room temperature from falling
below 41°F. Press the ON/STANDBY INDICATOR button at any time to turn off the
Standby/Anti-Frost function.
CLEANING, CARE AND STORAGE:
It is recommended that that the heater be cleaned at least once per month and
before storage.
- Before cleaning, turn off and unplug the heater. Allow it to cool completely.
- Wipe the exterior of the unit with a soft dry cloth. DO NOT USE WATER, WAXES, HARSH CHEMICALS OR CLEANERS, GASOLINE, BENZENE, PAINT THINNERS, ALCOHOLOR SOLVENTS.’
STORAGE : Keep original carton for storage of the heater.
Coil and tie the power cord to avoid damage during storage.
WARNING: ALWAYS UNPLUG THE CORD BEFORE MOVING, CLEANING OR WHEN NOT IN
USE.
WARNING : IMPORTANT! DO NOT IMMERSE HEATER IN WATER!
WARNING: DO NOT ATTEMPT TO DISASSEMBLE OR TAKE THE HEATER APART.
WARNING : DO NOT USE THE HEATER IF IT HAS MALFUNCTIONED OR BECOMES
DAMAGED IN ANY WAY.
NOTE: Do not tamper with or attempt to repair or adjust any electrical or
mechanical functions on this unit. There are no serviceable parts inside.
Tampering with or modify this product could result serious injury, death, or
fire. Risk of electric shock.
REFILLING : This heater is factory sealed and never needs refilling.
IMPORTANT SAFETY FEATURES:
heater is equipped with an automatic overheat protection device located inside
the body of the heater. If the heater gets too hot for any reason, the
automatic overheat protection device will turn the heater off. To reset the
heater, simply turn power off and unplug the heater for 10 minutes until it
cools down and then you may plug the heater in and restart. Be sure that the
heater
is on a smooth level surface with no obstructions. The heater is also equipped
with a safety tip-over switch to turn power off to the heater when the heater
tips over. To resume heater functions simply stand heater upright.
LIMITED WARRANTY
This unit is guaranteed to the original retail purchaser against defects in
quality or workmanship for a period of one year
from the date of original purchase. If this unit fails because of a
manufacturing defect within 30 days of purchase, return the unit, with your
receipt, to the retailer. After 30 days, but within the warranty period, if
the unit was purchased within the continental United States, return it,
freight prepaid, to World and Main for repair or replacement. If the unit was
purchased outside the continental United States, return the unit to the place
of purchase. This warranty does not cover damage caused by misuse, abuse,
overheating or alteration. Repairs made by anyone other than World and Main
are not covered in this warranty. World and Main will not be held liable for
any losses due to neglectful operation. All implied warranties, including the
warranties of merchantability and of fitness of purpose, if applicable, are
hereby limited in duration to the period of one year from the date of original
retail purchase. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitations may not apply to you. Incidental or
consequential damages arising from a breach of either express or implied
warranties are hereby disclaimed and excluded. Some states do not allow the
exclusion of limitation of incidental or consequential damages, so this
limitation or exclusion may not apply to you. Upon the expiration of this
warranty all such liability will terminate. No other warranties are expressed
or implied.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. No informal dispute settlement
mechanisms are available. This limited warranty is given in lieu of all other
warranties.
Manufactured for:
World and Main (Cranbury), LLC
324A Half Acre Rd.
C ranbury, NJ 08512 USA
800-221-6895
www.comfortzoneproducts.com
Rev. 06/01/2022
Rev. 06/01/2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>