SWIT PL-E60P Edge Gleaming Water-Proof LED Panel Light User Manual

June 3, 2024
SWIT

SWIT PL-E60P Edge Gleaming Water-Proof LED Panel Light

Thank you for choosing our products,please read this user manual carefully before using.

Introduction

This product is designed and apply to use in film, TV, photography and studio lighting, also can be used in theater, concert or other entertainment stage lighting.

Specification

Model PL-E60P PL-E90P
Color temperature 2700K-6500K
Brightness 0%-100%
luminance 1500 Lux@lm 2200 Lux@lm
Half beam angle About 70°(no honeycomb) About 40° (with honeycomb)
Beam angle ll0°
CRI 96 97
TLCI 99
Working Voltage DC ll-36V About 105W
Output Power About60W
Energy Efficiency Index

Test under this parameter: Dimmer=l00%, CCT=6500K

Ingress Protection| IP54
Dimension| Details find fig1, 2, 3
Lighting Area| 255mm x 255mm| 522mm x 255mm
Net Weight| 3.5Kg| 5.3Kg

Dimension

SWIT PL-E60P Edge Gleaming Water-Proof LED Panel Light
1

Caution

  1. Please do not disassemble the light or touch its inner part with metal;
  2. Please do not put the light under conditions full of dust or moisture to avoid damage;
  3. USB socket is reserved socket; pis use according to specified using environment for related products, and do not use for other purpose to avoid damage.
  4. When using interaction control function, pis do not connect to DMX output equipments, otherwise this function can not be used.
  5. Only use the light in the temperature range of -l0°C~40°C.

Maintain

  1. Please clean the front LED panel with soft dry cloth. If using soft cloth with slight clean neutral detergent solution, please wipe again with a soft dry cloth.
  2. Do not use wet cloth, anhydrous alcohol, gasoline, or a mixture of anhydrous alcohol and ether etc. to wipe the front LED panel.

Appearance

Front view:

SWIT PL-E60P Edge Gleaming Water-Proof LED Panel Light
6

  1. Mounting hole
  2. Diffuser
  3. U-sharp bracket connector
  4. U-shape bracket
  5. bracket knob

RearviewSWIT PL-E60P Edge Gleaming Water-Proof LED Panel Light
7

  1. Battery plate
  2. CT dimming knob
  3. DMXIN
  4. DC 11-36VIN
  5.  DMXOUT
  6. USB socket
  7. Power switch
  8. Dimmer knob
  9. LCD display

LCD display

For example: color temperature 5600K, dimmer 100%, powered by fully charged battery ,DMX communication mode, address008, it will display as below:

SWIT PL-E60P Edge Gleaming Water-Proof LED Panel Light
4

  1. Current communication control mode-OMX communication mode
  2. Current communication control mode-interaction control mode
  3. Brightness display
  4. Communication address
  5. CTdisplay
  6. Power supply display(AC adaptor power supply)
  7. Power supply display( battery power supply)

Note: When powered by battery, the battery capacity will be displayed as below:

Four LEDS About 80%-100%
Three LEDS About 60%-80%
Two LEDS About 40%-60%
One LEDS About 20%-40%

No display

(outline boarder flicker)

| Under 20%, lack of power

Optional Accessory Installation

Fig. 9~ 12 is the installation instruction for PL-E60P; the installation of PL-E90P is the same as PL-E60P.

SWIT PL-E60P Edge Gleaming Water-Proof LED Panel Light
5

Q)@ Barn door @@  Light body ® Small Honeycomb @@     Pressure plate
® Big Honeycomb (J) __ Low head screws @) shim ®@@ screws
  • The way to install the barndoor is shown as Fig.9 and Fig.11.
    Note: Put the low head screws upward during the installation.

  • Please confirm the types of honeycomb before using it. (The types of honeycomb size are shown as below).

  1. Purchase of big honeycomb The way to install the honeycomb is shown as Fig.10.
  2. Purchase of small honeycomb The small honeycomb can be used with the barndoor simultaneously. Fix the honeycomb by rotating the pressure plate (see Fig.12@) after the installation as shown in Fig.11, and then use the light normally.
Honeycomb type PL- EGOP PL- E90P
Big honeycomb (L X w X H) 290mm x 290mm x 10mm 558mm x 290mm x 10mm
Small honeycomb(L x W x H)) 268mm x 268mm x 10mm 536mm x 268mm x 10mm

Usage

Installation
Accessory installation
Pis check Optional Accessory Installation for the honeycomb (Fig.10 ®/ Fig.11 ®) and barn door (Fig. 9 G)) installation. 1.2 User can install the light on a tripod or stand, and adjust demanded beam angle by knob on both sides of the U-stand.

Power supply
The light provides two ways of power supply, byV-mount or Gold mount battery or by4-pin XLRAC-DC power. Turn on the light (Fig. 6@) and set the color temperature (Fig.6@} and brightness (Fig. 6 (j)) to user’s requirements.
Tips: The connection and disconnection of power adaptorXLR.

Connection
Align the hump of output male XLR to the gap of the DC socket,connect XLR and DC socket,the adaptor will connect with the light when you hear the crack sound.

Disconnection
Hold the hump of the DC output female XLR and pull out,the power adaptor and the light will be disconnected.

Dimmer and color temperature setting
The light provides two ways of adjusting the color temperature and brightness: normal adjusting mode and quick adjusting mode. User can switch the adjusting mode by press the dimmer knob and color temperature adjusting knob (Fig6.@/0). User can quickly set the dimmer and color temperature to their needs by combining two adjusting modes.

Normal adjusting mode

  1. Color temperature adjust Range: 2700K-6500K, adjust value: SOK
  2. Dimmer adjust

Quick adjusting mode

  1. Color temperature adjust Under this mode, user can quickly choose common color temperature: 2700K, 3200K, 4500K, 5600K, and 6500K
  2. Dimmer adjust: Range: 0%-100%, adjust value: 10%

Communication Address Setting and Usage

Press and hold dimmer knob (Fig 6@) for 2s to enter communication address setting interface, the address setting range is 001 to 512. LCD digital tube (Fig 8 ®) flashing means the current address is selected, rotate the brightness adjusting knob (Fig6@) to set the current address, press the brightness adjusting knob (Fig 6@) to confirm, when finish the last setting, press the brightness adjusting knob (Fig 6@) or wait for about 5s to quit.

Communication Control Mode Setting and Usage

Connect the lights network through using DMX cable. Press and hold color temperature adjusting knob (Fig. 6 0) for around 2 seconds to complete the communication control setting.

The upper left corner of LCD shows “DMX” (Fig. 8 G)) indicating that the communication control mode currently is the DMX communication mode. In this mode, connect the DMX signal output device to the lights network, and set up the communication address to work normally. A light occupies 2 DMX control channels. The current DMX address (N) is brightness control, and the next set address of the current value (N+ 1) is color temperature control.
For example:

DMX Communication address| DMX Control address| Function
---|---|---


005

| 005| Brightness 0%-100%
006| Color temperature 2700K-6500K

Interaction Control Mode

The upper left corner of LCD shows “CH” (Fig8 0) indicating that the communication control mode currently is interaction control mode. In this mode, set the target lights to the same communication address to work normally, and the master-slave machine is not distinguished.
Note: when using this mode, please do not connect the DMX signal output equipment in the lighting network; otherwise the function can not be used normally.

USB socket

USB socket is reserved socket. Pis use according to specified using environment for related products, and do not use for other purpose to avoid damage

Packing list

 | Packing list| Package 1| Package 2| Package 3
---|---|---|---|---
1| PL-E60P/PL-E90P| xl| xl| x3
2| Power cable| xl| xl| x3
3| Warranty card| xl| xl| x3
4| Carrying case| xl| I| I
5| User manual| xl| xl| x3
6| Adaptor| xl| xl| x3
7| Barn door| xl| I| x3
8| V-mount hook&loop| xl| xl| x3
9| Tripod| I| I| x3
10| Trolley case| I| I| xl
11| Ring (Optional)| ****





Customers can purchase separately according to the requirements

12| Safety rope (Optional)
13| DMX cable (optional)
14| Honeycomb (Optional)
15| Barn door(optional)


16

| Set of Barn door and Honeycomb(Optional)

Note:

  1.  Package 1: Single light package (with barn door)
  2.  Package 2: Single light package
  3. Package 3: KIT2 (with trolley case, barn door)
  4. The adaptor and LED PCB board can be changed , the parameters of recommend adaptor are below:
No. Specification Parameter
1 DC output socket 4Pin XLR
2 Adapter output power polarity Pin 111-11,Pin 4″+”
3 Working voltage AC 100-240V, 50/60Hz
4 Output voltage DC 11-36V
5 Voltage accuracy ±5%
6 Rated Power (Max.) 90W(PL-E60P)         105W(PL-E90P)
7 Power factor 0.9
8 Working temperature -l0°C-40°C

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals