Kenmore 111.99022810 Compact Refrigerator User Guide

Kenmore 111.99022810 Compact Refrigerator

PARTS AND FEATURES

1. Freezer compartment
2. Temperature control dial
3. Removable shelf
4. Drip Tray
5. Bottle storage
6. Leveling feet
   (Turn to left to raise; turn to right to lower)

SAVE THESE INSTRUCTIONS

DANGER
Rislcof child entrapment . Before you throw away your old refrigerator, take off the doors.
Leave the shelves in place so that children may not easily climb inside.

CFCs/HCFCs DISPOSAL
Your old refrigerator may have a cooling system that used CFCs or HCFCs (choro flour-carbons or hydro-chloro-flour-carbons) . CFCs and HCFCs are believed to harm stratospheric ozone if released to the atmosphere. Other refrigerants may also cause harm to the environment if released to the atmosphere.
If you are throwing away your old refrigerator, make sure the refrigerant is removed for proper disposal by a qualified technician. If you intentionally release refrigerant, you may be subject to fines and imprisonment under provisions of environmental legislation.

WARNING: When handling, moving, using or cleaning this refrigerator, be careful to avoid damaging refrigerant tubing. Tubing damage may allow flammable refrigerant gas leakage, which can result in personal injury.
Thank you for purchasing our Kenmore product .
This easy-to-use manual will guide you in getting the best use of your refrigerator.

PRODUCT RECORD

Staple your receipt to this manual.
Record the model and serial number of your unit in the spaces provided to the right.

• Model number:
• Serial number:

PREPARING TO USE YOUR REFRIGERATOR

Unpacking Your Refrigerator

1. Remove all packaging material. This includes the foam base and all adhesive tape holding the refrigerator accessories inside and outside.
   Slide out and remove the plastic or foam guard used to protect the compressor from shipping damage due to vibration and shock.

2. Inspect and remove any remaining packaging tope or printed materials before powering on the refrigerator.

3. Check to be sure you have all accessories and parts listed in the Parts and Features section.

Proper Air Circulation

To ensure that your refrigerator works at the maximum efficiency it was designed for, you should install it in a location where there is proper air circulation, plumbing and electrical connections.
The following are recommended clearances around the refrigerator:

• Sides.. .. 4 inches (10mm )
• Top…… 12 inches (30mm )
• Back.. 4 inches (10mm )

Electrical Requirements
Make sure there is a suitable power outlet (120volts, 15 amps) with proper grounding to power the refrigerator.

WARNING
These guidelines must be followed to ensure that safety mechanisms in this unit will operate properly.

• The unit must be plugged into its own dedicated 10 amp,120Volt, 60 Hz. AC only electric outlet.
  The power cord of the appliance is equipped with a three-prong grounding plug for your protection against shock hazards. It must be plugged directly into a properly grounded three-prong receptacle. The receptacle must be installed in accordance with local codes and ordinances.
  Consult a qualified electrician.

WARNING: Do not use an extension cord or adapter plug.

• Do not use appliance if the power cord is damaged or frayed. Take appliance to a qualitied service dealer tor inspection and possible repair.
• Never unplug the appliance by pulling on the power cord. Always grip the plug firmly, and pull straight out from the receptacle to prevent damaging the power cord.
• If your unit has an internal light, unplug the appliance before cleaning and before replacing light bulb to avoid electrical shock.
• Performance may be affected if the voltage varies by 10% or more. Operating the unit with inset ticket power can damage the motor. Such damage is not covered under the warranty.
• Do not plug the unit into an outlet controlled by a wall switch or pull cord t prevent the appliance from being turned off accidentally.
• Avoid connecting unit to a Ground Fault Circuit interrupter (GFCI).

DANGER

• Risk of fire or explosion.
• Flammable refrigerant used.
• To be repaired only by trained service personnel.
• Do not use mechanical instruments to remove frost from interior walls.
• Do not puncture refrigerant tubing.

OPERATING YOUR REFRIGERATOR

Installation

Your refrigerator is designed for freestanding installation only. It should not be recessed or built-in. Place the refrigerator on a floor strong enough to support it fully loaded. When moving the refrigerator, never tilt it by more than a 45 degree angle. This could damage the compressor and the sealed system. If the refrigerator has been tilted more than 45 degrees, let it stand in an upright position for at least 24 hours prior to plugging it into the power source. This will allow the refrigerant to settle and reduce the possibility of a malfunction in the cooling system. Plug the refrigerator into its own dedicated, properly installed grounded wall outlet. Do not plug another appliance into the same outlet as the refrigerator. Do not under any circumstances cut or remove the third (grounding) prong from the power cord. See the AWARNING in IMPORTANT SAFETY INSTRUCTIONS section. Any questions concerning power and/or grounding should bidirected toward a certified electrician or other qualified service dealer. After plugging the appliance into a wall outlet, allow the unit to cool down for 2-3 hours before placing food into the refrigerator.

Installation Limitations

Do not install your refrigerator in any location not properly insulated or heated, such as a garage etc. Your refrigerator was not designed to operate in temperature settings below 55 Fahrenheit Select a suitable location for the refrigerator on a hard even surface away tromp direct sunlight or heat sources such as radiators, baseboard heaters, Cooking appliances, etc.

Leveling Feet

There are two leveling teeth on the bottom of the unit near the unit trot. Turn the leveling foot knobs to the lit to raise the cabinet, and to the right to lower the cabinet.

DOOR REVERSAL

Door Reversal

WARNING: Unplug the refrigerator before performing door reversal process. Failure to unplug may result in serious injury or death from electrical shock.
CAUTION: To avoid personal injury and property damage, obtain assistance from another person for perform the door reversal process.

1. Using a flat blade screwdriver, remove the plastic hinge cover from the top of the door. Be careful not to scratch refrigerator surface.
2. Using a slotted screwdriver, unscrew the two screws from the top hinge bracket. Remove the bracket and underlying paper gasket. lift and remove the door from the bottom hinge pin. Set door safely aside.
3. Using a thin-bladed tool, carefully pry up and remove hole plug from top of door and the top of the opposite side of the cabinet. Insert plugs into provided hole on opposite side of door and into holes exposed by removal of top hinge bracket.
4. Unscrew and remove the leveling foot from the bottom hinge bracket. Using a slotted screwdriver, remove the three screws attaching the bottom hinge bracket to the cabinet. Unscrew the loot from the other side of cabinet. Attach bracket and feet to opposite sides from which removed.
5. Mount the door onto the bottom bracket. Be sure the plastic washer is on the bracket post. Insert top bracket hinge pin into hole in top of door. Use the two previously removed screws to attach back of top bracket to cabinet. Be sure to align the paper gasket beneath the two attachment holes in bracket.
6. Replace the plastic hinge cover over the top hinge bracket.
7. Check that the door is aligned horizontally and vertically with the the perimeter of the cabinet opening before finally tightening the top hinge. Alter tightening, adjust the leveling feet if necessary to to align the door evenly with the floor.
   CAUTION: If the refrigerator has been placed in a horizontal or tilted position for ease of door reversal, wait 24 hours before plugging it in. Plugging in sooner may result in permanent damage to cooling system.

FEATURES AND USE

Holder Bars

The inside of the refrigerator door is equipped with holder bars to keep food packages, bottles and pop cans securely in place on the door shelves.

Initial Use
To reach the set coldness level when operating the refrigerator for the first time, run it without food load until you hear the compressor stop.
This usually takes 2 to 3 hours. Once the set temperature is reached, load food into the refrigerator.
Note: If the refrigerator has been placed in a horizontal or tilted position for any period of time, wait 24 hours before plugging it in.

Temperature Control
The first time you turn the unit on, adjust the temperature control knob to Recommended setting (dot) and give your refrigerator time to cool down completely before adding food. Alter it is fully cooled, test it and adjust towards COLD to make less cool or towards COLDEST to cool more to best suit your needs.
Note: Turning the temperature control knob to the OFF position will stop the cooling cycle but does not shut off power to the unit.

Defrosting the Freezer

WARNING:

• When being defrosted the appliance must be unplugged to avoid the risk of electrical shock.
• DO NOT use a sharp or metallic instrument to remove frost from the refrigerator interior, as damage to refrigerant tubing may occur. Tubing damage may allow flammable refrigerant gas leakage , which can result in injury to persons.

For maximum energy efficiency , defrost the freezer section whenever frost accumulates to a thickness ol 1/ 8″ or more on freezer walls.

• Note that frost tends to accumulate more during the summer months.
• To defrost freezer section, open refrigerator door and door of freezer compartment.
• Remove all food from refrigerator and food and ice cube tray from freezer compartment.
• Place the drip tray on the shelf under the freezer compartment.
• Turn the refrigerator temperature control dial to the OFF position.
• Defrosting may take several hours, so store food in another refrigerator in the meantime.
• To speed up defrost time, keep the door open and place a bowl of warm water in the refrigerator.
• During the defrost cycle, water will accumulate in the drip tray .
• The drip tray may also need to be emptied during the defrost process.
• After defrosting, empty and wipe down the drip tray, as well as the interior of the refrigerator.
• You may now reset your refrigerator to the desired temperature and return food.

CAUTION: DO NOT use boiling water to melt frost accumulation on freezer walls, as it may damage plastic parts.
Normal Operating Sounds You May Hear Gurgling sounds or slight vibrations that are the result of the refrigerant circulating through the
cooling coils.
The thermostat control will click when it cycles on and off.

CARE AND CLEANING

Cleaning and Maintenance

WARNING: To avoid electric shock, always unplug your refrigerator before cleaning. Ignoring this warning may result in injury or death.
CAUTION: Before using cleaning products, always read and understand the cleaning processes explained in this manual. Follow cleaning product manufacturers’ instructions and warnings to avoid personal injury or product damage.

General Cleaning

Prepare a cleaning solution of 1 to 2 tablespoons of baking soda mixed with warm water. Use a sponge or soft cloth, dampened with the cleaning solution, to wipe down your refrigerator.
Rinse sponge or cloth with clean water, and wipe surfaces clear of any cleaning solution residue. Wipe all surfaces and racks dry with a soft cloth before resuming operation.
Do not use harsh chemicals, abrasives , ammonia, chlorine bleach, concentrated detergents, solvents or metal scouring pads. Some of these chemicals may dissolve, damage and/or discolor your refrigerator.

Door Gaskets
Clean door gaskets every three months according to the instructions described above in General Cleaning.
Gaskets must be kept clean and pliable to ensure a proper seal.
Petroleum jelly applied lightly on the hinge side of gaskets will keep the gaskets pliable and ensure a good seal.

Power Interruptions

Occasionally there may be power interruptions due to thunderstorms or other causes.
Remove the power cord plug from the AC outlet when a power outage occurs.
When power has been restored after a prolonged outage, inspect all food for spoilage.
Clean the inside of the refrigerator and freezer compartment before reuse.

Vacation and Moving Care

For long vacations or absences, unplug the unit, empty food from both compartments, move the temperature dial to the OFF position and clean the door gaskets according to the General Cleaning section. Prop door open, so air can circulate inside. When moving, always move the refrigerator vertically. Do not move unit when in a horizontal position, as possible damage to the sealed system could occur.
WARNING: When handling, moving, using or cleaning this refrigerator, be careful to avoid damaging refrigerant tubing. Tubing damage may allow flammable refrigerant gas leakage, which can result in personal injury.

TROUBLESHOOTING

1. No power to unit
2. Power cord is unplugged
3. Wrong voltage is being used

|

1. Check connection of power cord to power source
2. Plug in the unit
3. Use proper voltage

Refrigerator runs continuously|

1. Temperature set too low (too cold)
2. Door is not closed
3. Hot food inserted
4. Door opened too long or too often
5. Close proximity to heat source or direct sunlight

|

1. Set temperature higher (warmer)
2. Close door securely
3. Be sure food is at room tem­perature before inserting
4. Minimize door openings/du­ ration
5. Do not place unit close to heat sources or direct sun­ light

Internal temperature not cold enough|

1. No power to unit
2. Power cord is unplugged
3. Temperature control set too high (too warm)
4. Door is not closed
5. Hot food inserted
6. Door opened too long or too often
7. Airflow obstruction
8. Wrong voltage is being used
9. Close proximity to heat source or direct sunlight

|

1. Check connection of power cord to power source
2. Plug in unit
3. Check setting and change as needed
4. Close door securely
5. Be sure that food is at room temperature
6. Minimize door openings/du­ ration
7. Allow room for air to circulate around the unit
8. Use proper voltage
9. Do not place unit close to heat sources or direct sun­ light

KENMORE LIMITED WARRANTY

FOR ONE YEAR from the date of sale this appliance is warranted against defects in material or workmanship when it is correctly installed, operated and maintained according to all supplied instructions. WITH PROOF OF SALEa defective appliance will be replaced free of charge.
For warranty coverage details to obtain free replacement, visit the web page: www.kenmore.com/warranty
This warranty is void if this appliance is ever used for other than private household purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears Brands Management Corporation, Hoffman Estates, IL 60179

Sears Brands Management Corporation
Hoffman Estates, lL 60179 U.S.A.
www.kenmore.com
www.sears.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>