allen roth 3SMI350640 3SMI350640 Cordless Room Darkening Poly Cotton Roman Instruction Manual

3SMI350640 3SMI350640 Cordless Room
Darkening Poly Cotton Roman
Instruction Manual

Please read and understand these instructions before attempting to assemble, install, or operate this product.

Step 1: Check Package Contents

Before installing your shade, make sure all parts listed below are present. If any part is missing or damaged, please do not assemble, install, or operate. To request replacement  parts, contact customer service at 877-804-5504
Monday through Friday from 8:30 a.m. to 5:00 p.m. EST.

Contents include:

• Roman Shade
• Mounting Hardware Kit

Mounting Hardware Kit includes:

a. Mounting Bracket
b. 1 3/8-inch Screws
c. Handle for Bottom Rail| 2 (for shades up to 38 in. wide)
3 (for shades 39 in. to 56 in. wide)
4 (for shades 57 in. to 72 in. wide)
2 per bracket 1

Step 2: Gather Additional Tools Required

The following tools are not included, but will be needed to complete your
installation.

• Screwdriver
• Measuring tape
• Drill
• Pencil
• Step ladder

Tip: Use #6 plastic anchors for dry wall or plaster mounting (not included)
Tip: For screws, use a 3/32-inch drill bit; for wall anchors, use 1/4-inch drill bit.
Step 3: Install the Mounting Brackets
The shade may be installed either inside or outside the window frame. A mounting bracket should be positioned about one to six inches from each end of the head rail. For  wider shades that require three or more brackets, these should be spaced evenly between the two outermost brackets. Always position the brackets where there is no  interference with the cords and mechanisms inside the head rail. The procedure outlined below will assure proper bracket placement.
To attach the brackets position head rail where the inner front edge of head rail slides into slot at the front of mounting bracket. Push head rail upward until flexible tab at the bottom of bracket snaps in place.

For inside mounting, clip the brackets onto the head rail as described above.
Hold the shade in place and make a pencil mark at the rear of each bracket where it contacts the inside of the window frame.
Remove the brackets from the head rail and align them with the marks. Attach each bracket using the 1 3/8-inch screws, pre-drilling the screw holes using a 3/32-inch drill bit.

For outside mounting, attach the brackets to the head rail as described above.
Hold the shade level at the height desired and center it over the window opening.
Mark the exact location of each bracket with a pencil. Remove the brackets from the head rail and position the top of each bracket at the marked location and screw each  bracket into the wall or window molding using the 1 3/8-inch screws, pre-drilling the screw holes using a 3/32-inch drill bit.

Step 4. Secure the head rail
Place the head rail on the brackets as described in Step 3 above, and lock in place. Check carefully to assure that each bracket is properly secured.

To remove brackets from head rail
Use flathead screwdriver and insert into mounting bracket tab (a).
Push back tab with screw-driver to release bracket (a) from head rail.

Step 5. Attach the Handle

Attach the handle to the bottom rail as illustrated. The handle is designed to minimize contact with the shade’s fabric. Always raise and lower the shade SLOWLY to assure  that the pleated fabric stacks neatly.

• To lower the shade: grip the bottom-rail/handle and slowly pull straight down.
• To raise the shade: put your hand(s) under the bottom rail (palm facing up) and lift slowly until the desired height is reached.

Step 6. Install the Hold-Down Brackets
Hold-down brackets are provided for optional use and are typically used on doors with windows such as French doors. These brackets are intended to be used only if the shade is to be in a permanently lowered position. With the shade fully lowered, make pencil marks at the outside ends of the bottom rail. Brackets should be lined up to the  pencil marks and screwed into place using the 3/8-inch screws. Insert the pins protruding from the brackets in the holes on both ends of the bottom rail (see illustration).

REPLACEMENT PARTS

If you require replacement parts, contact customer service at 877-804-5504, Monday through Friday from 8:30 a.m. to 5:00 p.m. EST.
Please be sure to provide the following information, if possible:
The complete item number
A description of the product
The description of the part needed

ONE-YEAR LIMITED WARRANTY

For a period of one (1) year from the date of purchase, the manufacturer will replace this window covering with one of equal or superior value, if this window covering is  found to be defective in material or workmanship. To obtain warranty service, contact our customer service department at 1-844-318-6168.
This warranty does not cover damage of defects caused by or resulting from improper maintenance, negligent or improper use, abuse, misuse, neglect, accidents, act of God,  alteration, commercial use, installation, removal, or reinstallation.
This warranty is restricted to normal consumer use within the United States and Canada. MANUFACTURER WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. This warranty gives you specific legal rights, and you may also have other  rights, which vary from state to state.

QUESTIONS?
Contact customer service at 877-804-5504, Monday through Friday from
8:30 a.m. to 5:00 p.m. EST.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>