tala the Muse Portable Lamp on Battery User Guide
- June 9, 2024
- TALA
Table of Contents
Muse Portable Lamp on Battery
User Guide
the Muse Portable Lamp on Battery
Thoughtful lighting, responsibly designed in London.
Thank you for making the switch to Tala.
Discover the full Tala family at tala.co.uk
PREPARATION
Please read instructions thoroughly before installation and keep them for
future reference.
Improper assembly can undermine the safety and longevity of the product.
IMPORTANT
All packaging must be removed and bulb carefully screwed in before turning
on.
The product is designed to work with the Tala 12V LED bulb provided. Do not
use alternative bulb as product will not work effectively. For replacements,
visit the Tala website or contact us for assistance.
Avoid turning on product in hot temperatures above 35ºC.
Doing so will reduce lumen output and bulb lifespan.
To reduce risk of scratches or marking, ensure bulb is fully housed in the
glass case unless changing the bulb.
WARNING
The Muse is not suitable for recessed or enclosed fixtures or environments,
and should be displayed as instructed.
Do not leave the product under direct sunlight while switched on.
Ensure all fixings are tightly sealed and do not allow internal components and
surfaces to be exposed to water.
The Muse – Provided Components
A x1 The Muse luminaire
B x1 The Muse LED bulb in box
C x1 Flat-head screwdriver
D x1 USB Type-C Charging cable
- Handle
- Lid
- 12V LED bulb
- Lampholder coil
- Dimmer dial
- Base
- Battery charge level button
- USB Type-C power input
- Battery charge level
- Indicator lights
INITIAL SET UP STEP 1
Release the two screws 1a on the lid with the provided screwdriver B
and remove the handle 1.
STEP 2
Lift off the lid 2 and carefully remove all packing material from
inside including the bulb box.
STEP 3
Remove bulb from box and carefully screw into the lampholder coil by turning
the bulb clockwise.
Be careful to align the bulb properly and do not over-tighten.
The glass can be removed again after initial installation for better access to
bulb and lampholder coil. STEP 4
Ensure the bulb is screwed in fully and contact is made between the base of
the bulb and the housing, without overtightening.
The bulb and housing are both safe to touch.
IMPORTANT
Over-tightening or under-tightening of the bulb will cause misaligment.
If this occurs, make small adjustments until straight and just touching the
contact point. STEP 5
Return the lid and handle to the original position and tighten screws to
secure handle in place. STEP 6
To turn on, rotate the dial on the front of the lamp clockwise until the bulb
lights up.
Adjust the dimmer for your desired light output.
Dial the dimmer up for a cool white light, and dial down for a warm, ambient
colour temperature.
CHARGING THE MUSE
OPTION 1: WIRED CHARGING
Insert the provided USB Type-C charging cable into the input at the back of
the luminaire base and plug into a USB Type-A adapter.
For optimum charging, use the 0.5m charging cable provided and a 2-Amp USB
Type-A adapter.
OPTION 2: WIRELESS CHARGING
Place assembled product flat on a compatible wireless charging pad and ensure
it is placed on the centre of the pad for effective charging.
When charging correctly, the battery charge level indicator lights 8 will
start blinking.
Total charging time is 8 hours wired or 10 hours wireless.
BATTERY LEVEL INDICATOR
Press the button on the back of the lamp to display the battery level indicators on the front of the lamp. Press the button twice to turn the indicator lights off.
IMPORTANT
The Muse uses a Lithium-ion battery pack rated for 1000 full charge/discharge
cycles.
After this, the battery capacity may begin to noticeably degrade.
Tips to prolong the battery life are:
- Once fully charged, please remove from charger
- Avoid allowing the battery to reach 0%. Recharge when the low-battery indicator begins to blink
- When not in use, store The Muse with 25-50% battery (indicators 1-2)
- During charge, make sure The Muse is uncovered to avoid over-heating
- Depending on the charger power output, The Muse may not always charge to 100% if the bulb is on at the same time
The battery, bulb, and glass can all be easily replaced. For replacement parts, please visit our website or contact us at customerservice@tala.co.uk
CARE AND CLEANING
We recommend cleaning with a soft dry cloth. If required, further cleaning can
be achieved with warm, soapy water. Do not use abrasive materials as these
will damage the lacquer. Do not use alcohol or other solvents.
Extended use in wet or humid locations can cause condensation to form inside
the glass tube.
Please follow ‘Initial Set-Up’ steps to open the lid and allow condensation to
evaporate. To avoid condensation, it is recommended that the lamp is not
exposed to wet weather for long periods, such as left out in the rain
overnight.
WARRANTY AND AFTER-CARE
This product has a two-year warranty. If there appears to be a functional
defect with the product during this time, please contact our team at
customerservice@tala.co.uk.
THE MUSE
Ø12.5×33.8cm / Ø5×13.3in
IP44 | Suitable for Wet locations
5V/2A USB Type-C | 5W wireless
Battery: Li-ion 13.2Ah 3.7V 48.8Wh
Ta max. 35ºC
Only use with Tala The Muse 12V bulbs
BULB
12V | 6W | 400lm | E27
35W replacement | 0.5A
CRI 97, R9 95 | 2000-2800K
Ø6 x 11cm | Flicker <1%
This symbol indicates that electrical and electronic equipment (WEEE) should
not be mixed with general household waste.
For recovery and recycling, please take this product to a designated
collection point where it will be accepted free of charge.
Many retailers offer this instore.
Disposing of this product correctly will help save valuable resources and
prevent any potential negative effects on human health and the environment.
Join the Community
Instagram: @tala | Facebook: talaHQ | Pinterest: TalaLED | Tag: lighttoliveby
Tala Energy Ltd, 25B Vyner Street, London, UK, E2 9DG |
hello@tala.co.uk
Tala Europe B.V, Bertus Aafjeshove 40, Nieuwegein 3437JN, Netherlands
Tala North America, Inc. P.O. Box 89 1051, Port Washington Blvd. Port
Washington, NY 11050, USA
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Caution; changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
https://qrco.de/bc8STmSKU – MUSE-PBL-SB-01
Documents / Resources
| tala
the Muse Portable Lamp on
Battery
[pdf] User Guide
the Muse Portable Lamp on Battery, the Muse, Portable Lamp on Battery, Lamp on
Battery
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>