DENALI LAH.24.10000 LED Headlight Mount Instruction Manual

June 9, 2024
DENALI

DENALI logo LED Headlight Mount
Husqvarna TE & FE Enduros
LAH.24.10000
Instruction Manual

LAH.24.10000 LED Headlight Mount

Thank you for choosing DENALI
We know you would rather be riding your bike than wrenching on it, so we go the extra mile to make sure our instructions are clear and as easy to understand as possible. If
you have any questions, comments, or suggestions don’t hesitate to give our gear experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM
Please Read Before Installing
DENALI products should always be installed by a qualified motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. DENALI takes no responsibility for damages caused by improper installation. Caution: When installing electronics it is extremely important to pay close attention to how wires are routed, especially when mounting products to the front fender, front forks, or fairing of your motorcycle. Always be sure to turn the handlebars fully left, fully right, and fully compress the suspension to ensure the wires will not bind and have enough slack for your motorcycle to operate properly.
Installation Tips
We strongly recommend using medium strength liquid thread locker on all screws, nuts, and bolts. It is also important to ensure that all hardware is tightened to the proper torque specifications as listed in your owner’s manual. For included accessory hardware please refer to the default torque specifications provided below. Inspect all hardware after the first 30 miles to ensure proper torque specifications are maintained.

Bolt Size in-lbs ft-lbs Nm
M3 10.0 in-lbs 1.0 Nm
M4 23.0 in-lbs 2.5 Nm
M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm
M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm
M8 13.5 ft-lbs 18.0 Nm
M10 30.0 ft-lbs 41.0 Nm
M12 52.0 ft-lbs 71.0 Nm

Hardware Sizing Guide
Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc. Remember, the length of a screw or bolt is measured from the start of the “mounting
surface” to the end of the screw, so only include the screw head when measuring countersunk screws. DENALI LAH.24.10000 LED Headlight Mount - fig
1

What’s In The Box?

DENALI LAH.24.10000 LED Headlight Mount

Kit Contents

(a) D7 Face Plate……..(LAH.24.002)……………………….Qty 1
(b) D4 Face Plate……..(LAH.24.003)………………………..Qty 1
(c) Mounting Bracket………(LAH.24.001)………………….Qty 1
(d) M5x14 ISO 7380……………………………………….Qty 5
(e) M5 Washer DIN 125………………………………………Qty 10
(f) M5 Nut DIN 985………………………………………………..Qty 5
(g) Husqvarna Wiring Adapter…….(DNL.WHS.097)………Qty 1
(h) DataDim™ Controller……..(DNL.WHS.11000)…………….Qty 1

Installing The Enduro Headlight

DENALI LAH.24.10000 LED Headlight Mount - fig 2

1.1 – Assembling The Mounting Bracket
This Enduro Headlight Mounting Kit is a designed to replace the OEM headlight of Husqvarna TE & FE models. The LED headlight will plug directly into the OEM harness and will be controlled from the original headlight light switch.
Step One: Begin by installing the aluminum face plate to the mounting bracket (c) using the M5 hardware (d,e,f). If installing the round D7 LED light use face place (a), if installing the square D4 LED light use face plate (b).DENALI LAH.24.10000 LED Headlight Mount - fig 3 **Note* Your headlight mask may differ in shape &/or color than the illustration.
1.2 – Installing The Mounting Bracket
Step Two: Remove the headlight mask from the motorcycle and uninstall the factory sealed beam headlight. Keep the factory self tapping screw from the lower headlight
mounting tab as it will be re-used during the installation of the LED headlight.
Step Three: Use the M5 hardware (d,e,f) to attach the mounting bracket to the upper headlight mounting tabs.
Step Four: Re-use the factory self tapping screw to attach the mounting bracket to the lower headlight mounting tab. The screw should be threaded into the hole closest to the front of the headlight mask.DENALI LAH.24.10000 LED
Headlight Mount - fig 4 1.3 – Installing The D4/D7 LED Light
Step Five: Remove the hinge from the D4/D7 LED light pod by removing the M8 bolts on either side of the pod. Be sure to keep the bolts, flat washers, lock washers and
rubber grommets. They will be re-used to install the light pod into the headlight mask.
Step Six: Insert the D4/D7 light pod into the mask from the front side, then re-use the M8 bolts, flat washers, lock washers and rubber grommets to attach the light pod to the mounting bracket.
Note: For maximum downwards adjustably, pull the light pod to the top of the slotted mounting points before tightening the M8 hardware.DENALI
LAH.24.10000 LED Headlight Mount - fig 5 1.4 – Wiring The Enduro Headlight
Step Seven: Plug the red 4-pin connector of the Husqvarna wiring adapter (g) into the factory headlight connector.
Step Eight: Plug the black 6-pin connector of the Husqvarna wiring adapter (g) into the DataDim Controller (h).
Step Nine:** Plug the black 3-pin connector of the Husqvarna wiring adapter (g) into the D4/D7 pod.

DENALI logoDENALIELECTRONICS.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

DENALI User Manuals

Related Manuals