IMMERGAS 3.024176 Magnetic Cyclone Filter Kit Instruction Manual
- June 9, 2024
- IMMERGAS
Table of Contents
IMMERGAS 3.024176 Magnetic Cyclone Filter Kit
FOR MODELS
- VICTRIX HYBRID / PLUS
- MAGIS VICTRIX
- VICTRIX TT SERIES
- VICRIX EXA
- VICTRIX TERA / 24 PLUS / V2
- VICTRIX OMNIA
- VICTRIX SUPERIOR
- VICTRIX ZEUS SUPERIOR
- VICTRIX ZEUS
GENERAL WARNINGS
- All products are protected with suitable transport packaging.
- The material must be stored in dry environments and protected against weathering.
- This instruction manual provides technical information for installing the kit. As for the other issues related to kit installation (e.g. safety in the work site, environment protection, injury prevention), it is necessary to comply with the provisions specified in the regulations in force and principles of good practice.
- Improper installation or assembly of the appliance and/or components, accessories, kit and devices can cause unexpected problems to people, animals and objects. Read the instructions provided with the product carefully to ensure a proper installation.
- Installation and maintenance must be performed in compliance with the regulations in force, according to the manufacturer’s instructions and by authorised professionally qualified staff, intending staff with specific technical skills in the plant sector, as envisioned by the Law.
DESCRIPTION OF THE PRODUCT
The magnetic cyclone filter is able to detect the ferrous residues present in the system’s water. Thanks to the two cocks in the kit, it facilitates maintenance by cleaning the filter without having to empty the circuit.
WARNINGS.
The magnets can withstand a maximum temperature of 100 °C, so it is
recommended not to exceed a temperature between 90 – 95 °C.
Magnetic fields:
- Keep the magnet at a safe distance from all objects and equipment that could be damaged by the magnetic fields.
- The magnetic field can affect the operation of pacemakers and internal defibrillators, therefore keep the magnet at a safe distance.
INSTRUCTIONS FOR THE INSTALLER
Install the cyclone filter on the system return connection using the pipes suitable for your boiler model as shown in the figures below (fig. 2); if necessary, adapt the bottom protective grid of the boiler.
CLEANING THE FILTER.
-
Disconnect the boiler from the power supply, close the cock upstream of the filter, partially discharge the hydraulic circuit pressure (see the appliance instruction manual) and then close the second shut-off cock.
Attention: check that the temperature of the system return water is not too hot otherwise take precautions to avoid burns. -
Place a container under the filter to collect the water contained in it.
-
Remove the clip and pull out the magnetic cartridge by pulling it downwards.
-
Clean the cartridge with a clean cloth and under running water.
-
Put the magnetic cartridge back in place, making sure that the centring pins match and that the sealing O-ring is not damaged. If necessary, replace it with a new one.
-
Lock the magnetic cartridge in place with the clip.
-
Open the two shut-off cocks and restore power to the boiler to bring it back to normal operating conditions; at the same time check the operating pressure of the appliance and, if necessary, restore it to a correct value.
KIT COMPOSITION
| Ref | Description | Q.ty |
|---|---|---|
| 1 | Cyclone filter | 1 |
| 2 | Interception cock | 2 |
| 3 | 24 x 16 x 2 flat gasket | 5 |
| 4 | Wall connection pipe | 1 |
| 5 | Victrix Zeus Superior connection pipe | 1 |
| 6 | Magis Victrix connection pipe | 1 |
| 7 | Victrix Superior connection pipe | 1 |
8
| Victrix TT Series – Victrix Zeus – Victrix Exa – Victrix Tera/24plus – Victrix Tera V2 – Victrix Hybrid/Plus – Victrix Omnia connection pipe| ****
1
HEAD LOSS CHART
The head loss of the cyclone filter must be considered when sizing of the plant. Figure 3 shows the head loss curve.
