MEDION E62474 MD 43474 Over Ear ANC Headphones User Manual

MEDION E62474 MD 43474 Over Ear ANC Headphones

Information about this user manual

Thank you for choosing our product. We hope you enjoy using this device.
Please read the safety instructions and the user manual carefully before using the device for the first time. Note the warnings on the device and in the user manual.

Always keep the user manual close to hand. If you sell the device or give it away, please ensure that you also pass on this user manual. It is an essential component of the product.

Explanation of symbols

If a block of text is marked with one of the warning symbols listed below, the hazard described in that text must be avoided to prevent the potential consequences described there from occurring.

• DANGER!
  Warning: risk of fatal injury!

• WARNING!
  Warning: risk of possible fatal injury and/or serious irreversible injuries!

• CAUTION!
  Warning: risk of minor and/or moderate injuries!

• WARNING!
  Warning: danger due to loud volume!

• NOTICE!
  Follow the instructions to avoid property damage!

• More detailed information about using the device!

• Follow the instructions in the user manual!

• Follow the instructions in the user manual!

• Due to the 5 GHz frequency range of the wireless LAN solution used, the device may only be used inside buildings in the EU.

• This symbol provides useful additional information for assembling or operating the device.

• Products that feature this symbol meet the requirements of the EU directives (see chapter entitled “Declaration of conformity”).

• Bullet point/information on steps during operation

• Instruction to be carried out

• Safety instructions to be observed

Proper use

The wireless headphones are designed for personal audio playback and can also be used as a Bluetooth® headset. This device is only suitable for use indoors in a dry environment.
The device is only intended for private use and not for industrial/ commercial use.
Please note that we shall not be liable in cases of improper use:

• Comply with all the information in this user manual, especially the safety instructions. Any other use is considered improper and can cause personal injury or property damage.

Safety instructions

Warning!
Risk of injury!
There is a risk of injury to children and persons with limited physical, sensory or mental abilities (for example, partially disabled people or older people with limited physical and mental abilities) or to those without experience and knowledge (such as older children).

• Keep the device and its accessories out of the reach of children.
• This device can be used by children over the age of 8 and by persons with reduced physical, sensory or mental abilities or by those without experience and/or knowledge, if they are supervised or have been instructed in the safe use of the device and have understood the dangers that result from it.
• Children must not be allowed to play with the device. Cleaning and user maintenance must not be carried out by children, unless they are aged 8 or over and are supervised.
• Children younger than 8 must be kept away from the device.

DANGER!
Risk of choking and suffocation!
There is a risk of choking and suffocation due to swallowing or inhaling small parts or plastic wrap.

• Keep all packaging materials used (bags, pieces of polystyrene etc.) out of reach of children.
• Do not allow children to play with the packaging material.
  The packaging material is not a toy.

NOTICE!
Risk of damage!
Risk of damage to the device due to improper use of the device.
Do not expose the device to extreme conditions. Avoid:

• high humidity, spray or wet conditions

• extremely high or low temperatures

• direct sunlight

• direct sources of heat (e.g. heaters).

• Do not operate the headphones below +10°C or above +35°C, and do not store them below 0°C or above +45°C.

• Prevent the device from coming into contact with moisture, water or spray.

• The device is not suitable for use in rooms with high humidity levels (e.g. bathrooms).

• Do not use the device in potentially explosive atmospheres.
  This includes petrol stations, fuel storage areas and areas where solvents are processed, for example. This device must also not be used in areas with particle-laden air (for example flour or wood dust).

• If the device has been moved from a cold room to a warm room, wait before charging the headphones.
  The resulting condensation may damage the device. The device can be operated safely as soon as it has reached room temperature.

• All devices that are connected to the headphones must comply with the requirements of the Low Voltage Directive.

WARNING!
Damage to hearing!
Excessive sound pressure when using earphones and headphones can result in damage to and/or loss of hearing.
Using headphones to listen to a device playing at high volume for an extended period can damage your hearing.

• Do not place any objects on the cables as otherwise they may be damaged.
• Do not expose plug connections to impacts/pressure, e.g. from lateral forces. This could cause internal and external damage to your device.
• Do not apply force when connecting cables and plugs and make sure that connectors are the right way round.
• Do not crush or bend the cable to avoid cable breaks and short circuit.
• Keep the device at a distance of at least one metre from sources of high-frequency or magnetic interference (televisions, speakers, mobile telephones, DECT telephones etc.) to avoid malfunctions.

Information on the integrated rechargeable battery

WARNING!
Risk of explosion!
There is a risk of explosion if the battery is replaced incorrectly.

• The rechargeable battery is an integral component of the device that cannot be replaced by users themselves.
• Charge the battery regularly and as fully as possible. Do not leave the battery discharged for a long period of time.
• Keep the headphones away from heat sources such as radiators or open flames such as candles.

WARNING!
Risk of chemical burns!
There is a risk of chemical burns if the rechargeable battery is handled incorrectly.

• Do not use the headphones if the rechargeable battery is damaged in any way.
• Do not take the battery apart or deform it.
• Leaked liquids must not come into contact with the skin, eyes or mucous membranes. Do not swallow the liquid under any circumstances.
• Always wear appropriate protective gloves when handling leaking rechargeable batteries.
• If you nevertheless come into contact with the liquid, rinse the affected areas with plenty of clean water.
• Consult a doctor immediately if you notice any skin changes or feel discomfort.
• Keep rechargeable batteries away from children. Consult a doctor immediately if rechargeable batteries are swallowed.

Cleaning

• Do not immerse the headphones in water. Do not allow water to enter the headphone pads.
• Avoid contact with hot water.
• Avoid the use of chemical solutions and cleaning products because these may damage the device surface and/or markings.
• Avoid the use of sharp objects when cleaning the device.

In the event of faults

DANGER!
Risk of electric shock!
There is a risk of electric shock due to live parts.

• Do not use the headphones or accessories if they are damaged in any way.
• Never try to open and/or repair a device component yourself.
• Do not modify the device without our prior consent.
• Only use replacement parts or accessories that we have supplied or approved.
• In the event of any defects or damage to the headphones or accessories, please contact our Service Centre.

Package contents

DANGER!
Risk of choking and suffocation!
There is a risk of choking and suffocation due to swallowing or inhaling small parts or plastic wrap.

• Keep packaging away from children.
• Do not allow children to play with the packaging material.
• The packaging material is not a toy!
  • Remove the product from the packaging and remove all packaging materials.
  • Check your purchase to ensure that all items are included. If anything is missing, please contact our customer service team within 14 days of purchase.
  • Before each use, check the headphones and accessories for any damage. Contact our Service team in the event of any damage.

The following items are supplied with your product:

• Headphones
• Micro USB charging cable
• Audio cable 3.5 mm jack
• User manual and warranty documents

Device parts

1. Left ear cup

2. Headband

3. Right ear cup

4. Operating LED

5. ANC mode button

6. Multifunction button
   Switch device on/off, Bluetooth pairing, start/pause playback, accept/reject calls

7. AUX IN
   Audio input (3.5 mm jack)

8. Microphone

9. Charging socket with micro USB port

10. Charge level indicator

Getting started

• Remove all packaging materials.

Charging the battery

• To charge the integrated battery, connect the headphones to your PC/laptop using the USB charging cable provided.
  The charge level indicator (10) lights up red during charging.

• Charge the headphones for at least two hours.
  The charge level indicator lights up blue when the headphones are fully charged.

Putting the headphones on

• Adjust the headband length so that the headphones (2) fit comfortably on your head.

Switching the headphones on/off

• Press and hold the multifunction button (6) for approximately 3 seconds to switch on the headphones.
  The headphones automatically connect to the last audio device connected.
  If the headphones have not yet been paired or there is no known device within range, the headphones switch to pairing mode after 10 seconds.
  The operating LED (4) flashes blue/red and the headphones start Bluetooth pairing mode.

• Press and hold the multifunction button for approximately 5 seconds to switch off the headphones.
  The headphones automatically switch off after 5 minutes of inactivity.
  When the battery charge is running low, the charge level indicator will flash red and you will hear an acoustic signal.
  You will need to charge the battery quickly if you want to continue using the headphones.

Connecting the audio output device via Bluetooth

In Bluetooth mode, you can receive audio signals wirelessly from an external Bluetooth-enabled audio output device. Make sure the two devices are not more than 10 metres apart.
Only one audio output device can be paired with the headphones at a time.

Follow these instructions to pair a new Bluetooth-enabled audio output device with the headphones:

• Enable Bluetooth mode on your audio output device.
• Press and hold the multifunction button (6) for approximately 3 seconds until the headphones switch on.

The headphones switch automatically to Bluetooth pairing mode. The operating LED (4) flashes red and blue alternately.

The device name of the headphones MD 43474 will be displayed in the device list on your audio output device as soon as the signal is found.

If you are prompted to enter a password for pairing, enter 0000.

• Now connect your Bluetooth-enabled audio output device to the headphones.
  You will find more information about the Bluetooth function of your audio output device in its user manual.

Once the two devices are paired with each other, the operating LED will flash blue and you will hear a sound through the headphones to confirm that they are connected.
When signals are being transmitted via Bluetooth, you can control playback using your audio output device and the multifunction button.
Every time the headphones are switched on, they automatically attempt to connect to the last audio output device connected via Bluetooth.

Disconnecting a Bluetooth connection

• You can disconnect an existing Bluetooth connection by pressing and holding the multifunction button for 2 seconds.
  The headphones then disconnect from the existing connection and switch to pairing mode.

• If you press and hold the multifunction button for 2 seconds during pairing mode, the headphones will reconnect to the last audio device connected.

Deleting all Bluetooth connections

• Switch the headphones off.
• Press and hold the multifunction button for 10 seconds to delete all existing Bluetooth connection information.
  The switch-on signal will sound and after some time the acoustic confirmation that all connection information has been deleted.

Connecting your audio output device using the audio cable

You can use the audio cable provided to connect your headphones to any device with a suitable audio connection (3.5 mm jack) and enable audio playback.

To do so, proceed as follows:

• Plug the audio cable jack into the AUX IN socket (7) on your headphones and connect the cable to your audio output device.
• Start playback on the connected audio output device.
  When signals are being transmitted via a cable, it is not possible to control playback using the multifunction button. In this case, you have to rely on the controls on your audio output device.

Operation

Controlling playback

• Press the multifunction button (6) to start/resume playback.
• During playback, press the multifunction button to pause playback.
• Press the multifunction button twice to play the next track.
• Press the multifunction button three times to restart the current track.

Setting the volume

• Turn the multifunction button clockwise to increase the volume.
  A signal sounds through the headphones when the maximum volume has been reached.

• Turn the multifunction button anticlockwise to decrease the volume.

Managing calls/hands-free calls

When the headphones are connected to a mobile phone via Bluetooth®, you can manage incoming calls using the multifunction button and use the headphones as a hands-free system.

• Press the multifunction button once quickly to accept an incoming call.
• Press the multifunction button twice quickly to reject an incoming call.
• Press the multifunction button during a call to end the call.

Calling up the voice assistant

• Press the multifunction button four times to call up the voice assistant of your mobile end device.

Noise suppression (active noise cancelling)

The noise suppression function helps to strongly dampen disturbing noises from
the surroundings.
When the headphones are switched on, noise suppression is disabled.

• Press the ANC mode button (5) once to switch on the transparency mode.
  In transparency mode, the outside noises are recorded via the integrated microphone (8) and played back via the headphones.

• Press the ANC mode button a second time to enable noise suppression.
  The operating LED flashes green as soon as one of the two functions has been enabled.
  To prevent unnecessary battery discharge, disable the noise suppression function when the headphones are not in use.

• Press the ANC mode button three times to disable noise suppression. The operating LED flashes blue.

Troubleshooting

• Charge the headphone battery.

No sound.| Connection fault|

• Pair your audio output device with the headphones again.
• Check that the audio cable is plugged in properly.

Volume set too low|

• Check the volume settings on the headphones and your audio output device.

Sound inter- ference during hands-free calls| Excessive back- ground noise|

• Move to a quieter location.

Audio output de- vice out of range of headphones|

• Move closer to the audio output device.

Volume set too high|

• Turn down the volume on your audio output device.

Cleaning

• Switch the headphones off and unplug the USB cable if it is plugged in.
• Use a dry, soft cloth to clean the headphones.
• Avoid the use of chemical solutions and cleaning products because these may damage the device surface and/or markings.

Storing the device when not in use

• If you do not intend to use the headphones over a relatively long period of time, store them in a cool, dry place and make sure that they are protected from dust and extreme temperature fluctuations.

EU declaration of conformity

MEDION AG hereby declares that the radio equipment type MD 43474 complies with the directive 2014/53/EU [(RE directive) and the directive 2011/65/EU (RoHS directive)]. The complete EU declaration of conformity is available at: www.medion.com/conformity.

Trademark information

The Bluetooth® word mark and logos are registered trademarks of Bluetooth SIG, Inc. and are used by MEDION under licence.
The USB™ word mark and logos are registered trademarks of the USB Implementers Forum, Inc. and are used by MEDION under licence.
Other trademarks are the property of their respective owners.

Disposal

PACKAGING

Your device has been packaged to protect it from damage in transit. The packaging is made of materials that can be recycled in an environmentally friendly manner.

DEVICE (ONLY IN GERMANY)

All electrical or electronic devices marked with the symbol shown must not be disposed of in normal household waste. Instead, the end consumer must dispose of these devices at a collection point separately from unsorted urban waste at the end of their service life.

End consumers must separate used batteries and accumulators that are not enclosed in the waste equipment from the equipment, as well as bulbs that can be removed from the waste equipment, without causing damage before it is handed over at a collection centre and taken to a separate collection point.

Distributors with a sales area for electrical and electronic devices of at least 400 square metres and distributors of foodstuffs with a total sales area of at least 800 square meters, who offer electrical and electronic devices several times a calendar year or on a permanent basis and make them available on the market, are obliged to take back waste equipment free of charge if the end consumer buys a new piece of electrical or electronic equipment of the same type and functionality at the point of supply or in the immediate vicinity and of up to three items of waste equipment per device type that are less than 25 cm in length on their longest side at the request of the end consumer in the retail store or in the immediate vicinity.

In case of distribution by means of remote communication, all storage and shipping areas for electrical and electronic devices of the distributors are considered to be the sales area and all storage and shipping areas as the total sales area. In addition, the collection of waste equipment in categories 1, 2 and 4 of Annex 1 as defined in Section 2 Para. 1 (heat exchangers, screens, monitors and devices containing screens with a surface area of more than 100 cubic centimetres, large devices), free of charge is also applicable to distribution through remote communication when new electrical or electronic devices are purchased by and delivered to a private household.

Free collection centres and, if applicable, additional collection points for the recycling of waste equipment are available to take back waste equipment in your area. You can obtain the relevant addresses from your local authority.

If the waste equipment contains data storage, all data must be backed up externally and then permanently, irretrievably deleted from the waste equipment. End consumers are solely responsible for ensuring that all personal data is deleted from the waste equipment to be disposed of.

The rechargeable battery is an integral component of the device, which means that users cannot simply replace it themselves.

DEVICE
The device is fitted with an integrated rechargeable battery. At the end of its service life, do not dispose of the device in the normal household rubbish. Instead, contact your local authority to find out how to dispose of it in an environmentally friendly manner at collection points for electrical and electronic scrap.

RECHARGEABLE BATTERIES
Do not dispose of used rechargeable batteries with household rubbish.
Rechargeable batteries must be disposed of correctly. For this purpose, retailers that sell batteries and local collection points provide containers in which you can dispose of them. Contact your local waste disposal company or your local authority for more information.

In connection with the sale of rechargeable batteries or the supply of equipment containing batteries, we are obliged to draw your attention to the following:
As the end user, you are legally required to return used rechargeable batteries.
The crossed-out wheelie bin symbol means that the rechargeable batteries must not be disposed of with household rubbish.

Technical specifications

General data

Weight:| 270 g
Dimensions (WxHxD):| 175 x 200 x 45 mm
Frequency response:| 20 Hz–20 kHz
Impedance:| 32 ohms
Broadband voltage detection:| 94.6 mV
Power supply
USB port (DC IN):| 5 V __ 1000 mA
Rechargeable battery (integrated)
Battery type:| Lithium polymer, 3.7 V, 1000 mAh, 3.7 Wh
Battery life:| Up to 50 hours
Battery charging time:| Approx. 3.5 to 4 hours
The charging time may vary depending on the charging method.
Connections
AUX IN:| 3.5 mm jack
Ambient temperatures
In operation:| +10°C to +35°C at a relative humidity of (non-condensing) max. 80%
Not in operation:| 0°C to +45°C at a relative humidity of (non-condensing) max. 80%
Bluetooth®
Bluetooth version:| 5.0
Bluetooth profile:| A2DP, AVRCP
Frequency range:| 2402–2480 MHz
Max. transmission power:| 8.2 dBm
Range:| Up to 10 metres (depending on environmental conditions)

Service information

Please contact our customer service team if your device ever stops working in the
way you want or expect it to. There are several ways for you to contact us:

• In our Service Community, you can meet other users as well as our staff, and you can also share your experiences and pass on your knowledge.
  You will find our Service Community at community.medion.com.

• Alternatively, use our contact form at www.medion.com/contact.

• You can also contact our customer service team via our hotline or by post.
  Opening times| Hotline number UK
  ---|---
  Mon–Fri: 08:00–20:00

Sat: 10:00–16:00

| )        0333 3213106
Hotline number Ireland
)        1 800 992508
Service address
MEDION Electronics Ltd.

120 Faraday Park, Faraday Road, Dorcan Swindon SN3 5JF, Wiltshire

United Kingdom

You can download this user manual and many other user manuals from our service portal at www.medionservice.com.
You can scan the QR code shown to download the user manual onto your mobile device from the service portal.

References

• ce.com
• Home - MEDION Community
• MEDION Service
• Aktuelles | LDI - Landesbeauftragte für Datenschutz und Informationsfreiheit Nordrhein-Westfalen
• medion.com/
• MEDION AG - MEDION Konformitätserklärungen
• MEDION Service
• MEDION Service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>