WOLFANG GA300 Action Camera User Manual

June 9, 2024
WOLFANG

WOLFANG Logo GA300 Action Camera
User Manual

GA300 Action Camera

Using the Dust-Proof Cover

WOLFANG GA300 Action Camera - Figure 1

Charging the Battery
The battery charging steps are as below:

WOLFANG GA300 Action Camera - Charging the Battery

Note: The outlet battery charger is not included.

TF Card Installation & Format

TF Card Installation

  1. WOLFANG GA300 Action Camera - TF Card Installation The camera ONLY supports a U3 TF Card with a capacity of 32-128GB, otherwise, the camera may become unusable.
  2. After installing the TF card correctly, format it from the setting menu before first use.

TF Card Formatting

WOLFANG GA300 Action Camera - TF Card Formatting

Product Introduction

Product Diagrams

WOLFANG GA300 Action Camera - Product Diagrams

① OK Button/Shoot Button
② Wi-Fi Indicator
③ Touch Screen
④ Working Indicator (Red)
⑤ Charging Indicator (Blue)
⑥ Power Button/Mode Button
⑦ Lens
⑧ Up Button| ⑨ Down Button
⑩ Speaker
⑪ USB Port
⑫ HDMI Port
⑬ TF Card Slot
⑭ Battery Cover
⑮ Tripod Screw Hole
---|---

Specifications

Model GA300
Lens 170 HD wide-angle lens
LCD 2.0″ LCD
APP iSmart DV2
Picture Format JPEG
Video Format MOV
Video Compression Format H.264
Data Connection Micro USB2.0, HDMI
Extended Memory MAX to 128G, Micro SDHC
Power 5V/1A
Microspeaker Support
Speaker Built-In
Battery 1350mAH
Video Time 4K/About 60min
Charge Time About 3-4 hours
Operating System Windows XP/7/8 SP3/Vista and Mac 10.5 or above
Working Temperature -10 ℃~ +55 ℃
Storage Temperature -20 ℃~ +70 ℃

Note: Product design specifications are based on the latest information at the time of writing, subject to change without notice, please refer to the actual camera while in use.

Attention

  • Avoid dropping the camera.
  • Keep the camera at a distance from any objects with strong magnetic interference, such as electric appliances and/or objects that send out strong radio waves.
  • Keep the camera away from water and liquids (unless equipped with waterproof case). They may cause the camera to malfunction.
  • Keep the camera away from children while charging. It takes 3 hours to fully charge the battery. You are advised to remove the battery after you finish using the camera to extend battery life.
  • We recommend you use a high quality U3 TF Card (32-128 GB) for the best results. Please format the TF card on the camera before using and restart the camera after formatting.
  • Do not expose the camera directly to high temperatures over 55°C.
  • Do not place heavy objects on the camera.
  • Do not place your TF card near strong magnetic objects to avoid data error or loss.
  • Do not use the camera when the battery is low.
  • Do not use the camera while charging.
  • Do not attempt to open the case of the camera or dissemble it in any way.
  • Please remove the battery if you intend to use the camera as a dash camera.
  • When the camera is overheating or is emitting smoke or an unpleasant smell, unplug it immediately from the power outlet to prevent fire.
  • Please store the device in a cool, dry and dust free location.

Indicator light

Working Indicator| 1. While recording a video, the LED continuously flashes.
2. When taking a photo, the LED quickly flashes 3 times.
3. When powered, the LED is off.
---|---
Charging Indicator| 1. While charging, the LED is bright (blue).
2. When fully charged, the LED is off.
Wi-Fi Indicator| 1. When camera is on, the LED is a solid red light.
2. When recording a video, the LED continuously flashes.
3. When the Wi-Fi is turned on, the LED continuously flashes.

Button instruction

Power/Mode Button| 1. Long press the Power key to the camera, short press to turn on/off the Wi-Fi.
2. Short press to switch setting option when in settings.
---|---
Down Button| 1. Single press to turn on/off voice recording when shooting a video.
2. Single press to switch to the next photo in photo playback.
Up Button| 1. Single press up button turns on the Wi-Fi.
2. Return to the former interface.
OK Button| 1. Shutter function while in Video/Photo mode.
2. Long press to bring up the video menu, touch screen to select, or short press to confirm the current option. Long press when in photo mode to bring up photo menu use the up/down key to select, short press to confirm.
3. Long press in File playback to access the preview list while in the playback interface, and use the up/down key to select, short press to confirm.
4. While in Video playback, press to Pause/Play.

Mode Operation Instructions

Video Mode
The camera will automatically display video mode when powered on.

① Video Mode
② Recorded Video Time
③ Available Record Time
④ Microphone| ⑤ Battery Life
⑥ Video Playback
⑦ Resolution/fps
⑧ Menu Setting
---|---

Press the bottom middle of the screen or long press the OK button to choose different modes for video.

WOLFANG GA300 Action Camera - different modes

Press to enter video setting mode

WOLFANG GA300 Action Camera - ideo setting mode

Photo Mode
Open the camera and it will automatically display video mode. Then right or left swipe to change it to photo mode.

  1. Photo Mode
  2. Photo Quantity/Available Photo Shoot Quantity
  3. Battery Life
  4. Photo Playback/Photo Files
  5. Photo Resolution
  6. Photo Setting

Press the bottom middle of the screen or long press the OK button to choose different modes for photo.

WOLFANG GA300 Action Camera - different modes for
photo

Press to enter photo setting mode

WOLFANG GA300 Action Camera - Figure 2

System Setting

  • Power Frequency: 50Hz/60Hz
  • Sounds: Shutter, Boot-Up, Beep, Volume
  • White Light Balance: Auto, Daylight, Shade, Tungsten Light, White Fluorescent, Underwater. (By adjusting this setting, the camera can correct the color of photos taken under different lighting conditions.)
  • Effect: Normal, BW, Natural, Negative, Warm, Brightness Contrast
  • Distortion Calibration: On/Off. (To adjust for the fish eye effect)
  • Date & Time: Set Date and Time for the camera
  • Screen Saver: Off, 1min, 3min, 5min. (After a set period of time, if there is no operation on the camera ,the screen will automatically turn off. At this point the camera does not turn off, you can press any button to light up the screen.)
  • Auto Power Off: Off, 1Min, 3Min, 5Min. (After a set period of time, If there is no operation on the camera, the camera will automatically shut down.)
  • Power On Auto Record: On/Off (When you open the camera it will automatically starts to record video.)
  • USB: MSDC/PCCAM(UVCMJPG)
  • Language: English/Français/Deutsch/Italiano/Espanol/
  • Format Card: Format the memory card in the camera. Once this operation is implemented, all data will be deleted
  • Factory Reset: Reset all camera settings to default settings
  • System Info: Firmware version
  • Card Info: Card capacity and remaining memory

Wi-Fi/PC/TV Connection

Wi-Fi Connection
The Wi-Fi Application allows you to control your camera remotely on a smart phone or a tablet. You can view the videos and pictures shot on your phone, download them directly to your phone.
The connecting steps are as follows:
A: Download the iSmart DV2 App on your smart phone or tablet in Google Play or Apple App Store.
B: Short press the up button to turn on Wi-Fi, short press again to Exit. The status light (RED)on the top of the camera remains flashing while the camera is waiting for Wi-Fi connection and the light stays on when the Wi-Fi is connected.
C: Find and connect the Wi-Fi in the Wi-Fi list on your phone with the Wi-Fi name and password displayed on the camera.

WOLFANG GA300 Action Camera - Figure 3

D: Open the iSmart DV2 App on your smart phone or tablet after the Wi-Fi is connected, you’ll find the camera is controlled by your phone.

Connecting to a Computer
When you use the included micro-USB cable to connect to a computer, you can access to the files which are stored in camera’s micro SD card to copy or view them on a computer. This function can also achieve by a micro SD card reader.
Connecting to a TV
With an HDMI output, you can display the movies and images recorded by this camera on a TV, projector, etc.

  1. Turn off the camera.
  2. Connect the camera and TV with a commercially available Micro HDMI cable (Not Included).
  3. Turn on the camera and turn on the HDMI setting on the device which you intended to input.

Tips:

  1. The HDMI input device should support 1080P.
  2. When outputting HDMI ,the display of the camera turns back. The screen is displayed on the HDMI input device, but you will use the camera for basic operation (e.g. selecting the video/pictures to view)

WOLFANG Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals