WOLFANG GA400 Action Camera User Manual

WOLFANG GA400 Action Camera

Installation Guide

Note : The outlet battery charger is not included in this camera package.

TF Card Installation & Format

1. The camera ONLY supports U3 TF Card with a capacity of 32-128G, otherwise, it may cause the camera unusable.
2. After installing the TF card correctly, format it from setting menu before the first use.

TF Card Formatting

Introduction of host

Product Diagrams

1. Lens
2. Mode Button
3. OK/ Shoot Button
4. WiFi / Power Button
5. Touch Screen
6. Charging Indicator (Red)
7. WIFI Indicator (Blue)
8. USB / HDMI Port
9. Speaker
10. Tripod Mount
11. Battery Cover

Specifications

Battery

Charge Time

| 1350mAH

About 3-4hours

Operating System

| Windows XP/7/8 SP3Nista and Mac

10.5 or above

Working Temperature| -10’C-+55’C
Storage Temperature| -20’C-+70’C

Note : The product specifications are formulated in accordance with the latest information at the time of writing of this specification. If any changes are subject to prior notice, please follow the actual camera.

Attention

• Avoid crushing and dropping.
• Keep the camera away from any strong magnetic interference objects like electrical machine to avoid strong radio waves that might damage the product and affect the sound or image quality.
• Keep the camera away from water and liquids (unless equipped with waterproof case). This may cause the camera to malfunction.
• Keep it away from children while on charging. It takes 3 hours to fully charge the battery. You are advised to remove the battery after you finish using the camera to extend battery life.
• We recommend you use high quality U3 TF Card (32-128 GB) for the best results. Please format the TF card on the camera before using and restart the camera after formatting.
• Do not expose the camera directly to high temperatures over 55°C.
• Do not place heavy objects onto the camera.
• Do not place your TF card near strong magnetic objects to avoid data error or loss.
• Do not use the camera when the battery is low.
• Do not use the camera while charging.
• Do not attempt to open the case of the camera or dissemble it in any way.
• Please remove the battery if you intend to use the camera as a dash camera.
• When you find the camera overheats, unwanted smoke or unpleasant smell, unplug it immediately from the power outlet to prevent hazardous fire.
• Please store the device in a cool, dry and dust free location.

Indicator light

Working

Indicator

| 1. While recording a video, LED continuously flashes.

2. When taking a photo, LED quickly flash 3 times.

3. Power off, LED is off.

---|---
Charging Indicator| 1. While charging, LED is bright(Red).

2. Charge fully, LED is off.

Wi-Fi Indicator| 1. When the Wi-Fi opens, LED continuously flashes.

2. When WiFi connected, LED is bright(Blue).

Button Instruction

Power/WiFi Button| 1. Long press Power key to open the camera.

2. short press to open/off the WIFI.

3. While in boot state, long press power key to shut down

---|---
OK Button| 1. Shutter function while Video/Photo mode.

2. Long press into menu setting while video/photo interface, touch screen to select, or short press to confirm for the current option.

3. Video playback status, press to Pause/Play.

Mode Button

| 1. Short press to switch setting option when in setting interface.

2. Short press to change mode from photo or video.

Mode Operation Instructions

Video Mode
The camera will automatically display video mode when power on.

1. Video Mode
2. Recorded Video Time
3. Available Record Time
4. Microphone
5. Battery Life
6. Video Playback
7. Resolution/fps
8. Menu Setting

Press 12100,30 1 or long press OK button to choose different modes for video.

Press VOICE RECORD to enter video setting mode

Photo Mode
Open the camera and it will automatically display video mode. Then right slide or left slide to change it to photo mode.

1. Photo Mode
2. Photo quantity/Available Photo Shoot Quantity
3. Battery Life
4. Photo Playback/Photo Files
5. Photo Resolution
6. Photo Setting

System Setting

• Power Frequency: 50Hz/60Hz

• Sounds: Shutter, Boot-up, Beep, Volume

• White Balance: Auto, Daylight, Shade, Tungsten Light, White Fluorescent, Underwater. (By adjusting this setting ,the camera can correct the color of photos taken under different lighting conditions.)

• Effect: Normal, BW, Natural, Negative, Warm, Brightness Contrast

• Distortion Calibration: On/Off. (To adjust for the fish eye effect)

• Date & Time: Set Date and Time for the camera

• Screen Saver: Off, 1 min, 3min, Smin.
  (After a set period of time, if there is no operation on the camera ,the screen will automatically go black. At this point the camera does not turn off, you can press any button to light up the screen.)

• Auto Power Off: Off, 1 Min, 3M in, SM in.( After a set period of time, If there is no operation on the camera.the camera will automatically shut down.)

• Power On Auto Record: On/Off.
  (When you open the camera it will automatically starts to record video.)

• USB: MSDC/PCCAM(UVCMJPG)

• Language: English / Frani;ais /Deutsch / Italiano/ Espanol /B :zls:? / fri;j{.$:q:,y

• Format Card: Format the memory card in the camera. Once this operation is implemented, all data will be deleted.

• Factory Reset: Reset all camera settings to default settings

• System Info: Firmware version

• Card Info: Card capacity and remaining memory.

WIFI/PC/TV Connection

Wi-Fi Connection
The Wi-Fi Application allows you to control your camera remotely on a smart phone or a tablet. You can view the videos and pictures shot on your phone, as well as downloading them to your phone.

The connecting steps are as following:

• Download the iSmart DV2 App on your smart phone or tablet in Google Play or Apple App Store.
• Short press the “Power Button” on the front to turn on WI Fl, short press again to Exit. The status light (RED)on the top of the camera remains flashing while the camera is waiting for Wi-Fi connection and the light stays on when the Wi-Fi is connected
• Find and connect the Wi-Fi in the Wi-Fi list on your phone with the Wi-Fi name and password displayed on the camera.
• Open the iSmart DV2 App on your smart phone or tablet after the Wi-Fi is connected, you’ll find the camera is controlled by your phone.

Computer Connection
When you use the included micro-USB cable to connect to a computer, you can access to the files which stored in camera’s micro SD card to copy or view them on a computer. This function can also achieve by a micro SD card reader.

TV Connection
With HDMI output, you can display the movies and images recorded by this camera on large screens of T\/, projector, etc.

1. Turn off the camera.
2. Connect the camera and 1V with a commercially available Micro HDMI cable (Not Included).
3. Turn on the camera and turn on the HDMI setting on the device which you intended to input.

Tips:

1. The HDMI input device should support 1080P.
2. When outputting HDMI, the display of the camera turns back. The screen is displayed on the HDMI input device, but the operation is operated with the camera.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>