JETSON AFLOW-16 LED Strip Lights User Guide

: June 4, 2024
: Jetson

Table of Contents

Safety Warnings
Specs & Features
Get Started
How To Control Your Lights
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

Flow
LED Strip Lights.

A guide for your lights.
IMPORTANT: READ CAREFULLY, RETAIN FOR FUTURE REFERENCE.
MODEL: AFLOW-16 | AFLOW-32 | AFLOW-64

Safety Warnings

Keep these instructions.
Non-user replaceable light sources.
Uncoil the light strip before use.
Do not drop, puncture, open, cut, or disassemble this product.
Do not install this product in any way other than what is outlined in this guide.
Do not place this device on hot surfaces.
Only use the adaptor supplied; using a different adaptor can damage the device.
Do not submerge the strip or the power supply unit in water.
Avoid long exposure to direct sunlight, which may cause damage.
Do not use this product in small, enclosed locations that could limit the flow of air or trap excess heat.
Do not expose this product to open flames or use near fire.
Do not use the product in a strong magnetic field.
Do not use this product for emergency lighting/exits.
Do not allow small children to operate, modify, or install this device unsupervised.
Use a clean, soft cloth to clean – do not use any cleaning agents to clean.
Manage in accordance with disposal laws in your area.
Do not clean the device when it is on and connected to the power supply.
Do not connect the light strip to the power supply while in its packaging or wound onto its reel.
Do not use the rope light when covered or recessed into a flat surface.
Not intended for illumination; only use for ambiance.

California Proposition 65
WARNING:
This product can expose you to a chemical such as Cadmium that is known to the state of California to cause cancer or birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov/product
NOTICE OF COMPLIANCE
Changes or modifications not expressly approved by Jetson could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed nd used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in an articular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user s encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20 cm between the radiator & your body.
LIMITED 1-YEAR WARRANTY
Limited 1 Year Warranty only applies to the manufacturer defects. Contact Jetson Customer Care for detailed information via support. ridejetson.com
Limited 1 Year Warranty does NOT cover:

Normal wear and tear
Improper assembly
Corrosion
Improper maintenance
Installation of components, parts, or accessories not originally intended for or compatible with the product as sold
Damage or failure due to accident, misuse, abuse, or neglect
Labor charges for part replacement or changeover
Non-proprietary products (any other original part or component) covered by the original manufacturer’s warranty
Any accessories

Specs & Features

POWER SUPPLY: 12V AC ADAPTER
OUTPUT POWER: 16FT=12W, 32FT=24W 64FT=36W
OPERATING TEMPERATURE: BETWEEN -4F AND 113F
REMOTE CONTROL RANGE: UP TO 26FT
REMOTE CONTROL BATTERY: CR2025 OR EQUIVALENT
IP20 NON-WATER RESISTANT – FOR INDOOR USE ONLY

What’s in the Box

LED STRIP LIGHTS
REMOTE
CONTROLLER
AC ADAPTER
MOUNTING ADHESIVE

Get Started

1.1 Preinstallation

CHECK THAT YOU HAVE EVERYTHING. BOX SHOULD CONTAIN AMBER FLOW STRIP, CONTROLLER, AC ADAPTER, REMOTE CONTROL AND MOUNTING ADHESIVE.

1.2 Installing Your Lights

WIPE DOWN AND CLEAN THE SURFACE YOU’RE PLANNING TO PLACE YOUR LIGHTS ON.
PEEL OFF THE PROTECTIVE TAPE ON THE BACK OF THE LIGHTS.
PLACE LIGHTS ONTO SURFACE. PRESS DOWN TO MAKE SURE ADHESIVE IS FIRMLY SECURED TO SURFACE.
INSERT THE CONTROLLER INTO THE LIGHTS. ENSURE THAT ARROWS LINE UP CORRECTLY.
INSERT THE AC ADAPTER INTO THE CONTROLLER.
PLACE POWER ADAPTER INTO ELECTRICAL OUTLET.

How To Control Your Lights

2.1 Controlling with the Controller

2.2 Controlling with the Remote

CONTROL AND CUSTOMIZE YOUR AMBER LIGHTS USING THE INCLUDED REMOTE.

CREATING CUSTOM COLORS:

PRESS EITHER THE ‘DIY1’, ‘DIY2’, OR ‘DIY3’ BUTTONS.
PRESS THE ‘DOWN’ BUTTON IN EITHER RED, GREEN, OR BLUE TO CHANGE THE LED LIGHTS FROM THE DEFAULT COLOR (WHITE).
CONTINUE TO ADJUST EITHER RED, GREEN, OR BLUE BY PRESSING THE ‘UP’ OR ‘DOWN’ BUTTONS UNTIL YOU REACH YOUR PREFERRED COLOR.
PRESS THE SAME ‘DIY’ BUTTON THAT YOU DID IN STEP 1. YOUR COLOR IS NOW SAVED, AND CAN BE RETRIEVED BY PRESSING THE SAME ‘DIY’ BUTTON AT ANY TIME.

NOTE: YOU CAN NOW USE ADDITIONAL EFFECTS BUTTONS, SUCH AS ‘FADE’. TO RETURN YOUR PREFERRED COLOR WITHOUT THESE FUNCTIONS, PRESS THE RELEVANT ‘DIY’ BUTTON.
Enjoying the ride?
Leave a review on ridejetson.com/reviews or share your photos with us online using the #RideJetson hashtag!

Follow us @ridejetson
#MakeMoves Questions? Let us know.
support.ridejetson.com
Hours of Operation:
7 Days a Week, 10am-6pm
Manufactured in Shenzhen, China
Imported by Jetson Electric Bikes LLC.
86 34th Street 4th Floor, Brooklyn, New York 11232
www.ridejetson.com
Designed in Brooklyn
Made in China
Date Code: 10/2021