GOLDEN LIGHTING 3509-9 BLK Landon 9 Light Matte Black Chandelier Ceiling Light Instruction Manual
- June 13, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 3509-9 BLK Landon 9 Light Matte Black Chandelier Ceiling
Light
Product Information
The product is a lighting fixture manufactured by Golden Lighting. It is available in various models and styles, including pendants, linear pendants, chandeliers, sconces, and flush mounts. The fixture is designed to provide both task and ambient lighting in residential spaces.
Features:
- Various models and styles are available
- Designed for residential use
- Provides task and ambient lighting
- Coordinating fixtures available for layered lighting
- Dimmers compatible with controlling light output
Specifications:
- Fixture Height: Varies depending on model
- Fixture Width: Varies depending on the model
- Minimum Hanging Height: 30″ above countertop or table
- Minimum Clearance from Floor: 7.5 feet
Product Usage Instructions
Pendants & Linear Pendants Above a Kitchen Island:
- Center a linear pendant over the kitchen island.
- If using hanging pendants, use one pendant for every 24″ of island width.
- Fixtures should hang at least 30″ above the countertop.
Pendants & Chandeliers Above a Dining Room Table:
- Fixtures should hang at least 30″ above the table.
- Use a fixture that is 12″ narrower than the width of the table.
Pendants and Chandeliers in Open Areas:
- The bottom of the fixture should hang at least 7.5 feet from the floor.
- Allow clearance for any opening doors.
Installation:
- Follow the assembly instructions provided with the specific model of the fixture.
- Identify the fixture’s wires: Hot, Neutral, and Ground.
- Connect the fixture’s wires to the power supply wires from the junction box:
- Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire).
- Connect Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire).
- Connect Ground to Ground (transparent wire with copper, bare metal, green, or transparent inner thread).
- Have an assistant support the fixture’s weight while completing the wiring.
- Once the wiring is complete, finish the installation according to the provided instructions.
Note:
For further assistance or replacement parts, contact the place of purchase or
visit the Golden Lighting website.
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by an accredited professional.
- Shut off the power supply at the fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove the old fixture from the wall, including the
old mounting strap.
-
From the parts, bag remove the mounting strap (D) assembly. One end of the nipple (A) should be attached to the mounting strap (D) with a washer (C) and hex nut (B) in place. Attach the mounting strap (D) to the junction box using mounting screws (F) and a screwdriver. Tighten securely. Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over the mounted canopy loop (H) to test the height. Approximately half of the canopy loop’s exterior threads should be exposed, and the canopy loop collar (I) should fit snugly onto the canopy loop (H). Remove the canopy (G) and adjust the height of the nipple (A) and canopy loop (H) until the desired height is reached.
ASSEMBLING THE FIXTURE -
Place the fixture’s frame onto a flat surface. Turn the fixture frame upside down so that the bottom cap (O3) is facing up. Unscrew hex nut (O1) and remove the bottom cap (O3) from the nipple (O). Inside the fixture base, carefully pull the wires (O2) inside the base to help guide fixture arms (W) into the supports (Y). Place bottom cap (O3) back over nipple (O) and secure with hex nut (O1) and finial (P). Turn the fixture frame back over to the original position. Once arms (W) are in place, secure to the fixture using small screws (X).
-
Thread long nipple (L) into post (N) and secure with hex nut (Z4). Feed the fixture’s wires from the post (N) through the long nipple (L). Pull the wires until taut. Assemble decorative column (M) and slide over long nipple (L), then carefully push the wires through long nipple (L), decorative cap (Z3), washer (Z2), and into the hole in the top loop (Z1). Thread the top loop (Z1), washer (Z2), and decorative cap (Z3) onto the decorative column (M) to secure the top loop (Z1) to the fixture. Pull the wires until taut.
-
Measure to determine the correct length of chain needed for proper hanging height. If necessary, use a pair of pliers to open and remove any excess chain. Attach each of the chain connectors (J) to each end of the chain (K) before attaching one end of the chain connector/chain to the top loop (Z1). Connect the other chain connector (J) to the canopy loop (H). Close the chain connectors (J) to secure.
-
Feed the fixture’s wires up through the chain (K) (every three links or so), pulling the wires until taut. Gently slide canopy loop collar (I) and canopy (G) down onto the chain/wires. Trim excess wires leaving about 8 to 10 inches for later.
CONNECTING THE WIRES -
Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of the ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
How to Identify the Fixture’s Wires -
Hot: Smooth, Black, or Transparent with Black Inner Thread
-
Neutral: Ribbed, White, or Transparent with White Inner Thread
-
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
FINISHING THE INSTALLATION -
Push the canopy (G) up to the ceiling and slide the canopy loop collar (I) up beneath the canopy (G). Tightly thread the canopy loop collar (I) onto the canopy loop (H) to secure the canopy in place until snug against the ceiling. 8. Slide candle sleeves (U) over sockets on cups (V). Tighten decorative finials (S & Q) onto the threads (R1 and R2) at the bottom of the fixture arms. Install light bulbs (not included) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is now complete. Turn on the power and test the fixture.
Dimension
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of the island. Fixtures should hang at least 30″ above the
countertop.
Pendants and chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style!
Browse our site for coordinating lights and expert lighting advice. To help
create the perfect look, visit
www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
- Facebook: @GoldenLighting
- Instagram: @GLFixtures
- Twitter: @GoldenLighting1
- Pinterest: @GoldenLighting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>