JETSON JMCKY-STX3 Mickey Mouse Customizable Kick Scooter User Manual

JETSON JMCKY-STX3 Mickey Mouse Customizable Kick Scooter

Product Information MickeyTM Customizable Kick Scooter

The MickeyTM Customizable Kick Scooter is a limited edition product designed in Brooklyn. It comes with a sticker pack that allows users to customize the stem of their scooter. The product is equipped with motion-activated LED light-up front and rear wheels that illuminate when in motion. The scooter also features a rear foot brake for safe and easy stopping. The handlebar height is adjustable, and the stem can be removed for easier storage and transport. The product comes with a 2-bit Phillips-head screwdriver and Allen key tool for adjustment and maintenance. Adults must assist children in the assembly and initial adjustment procedures of the product. Closed-toe, flat shoes are recommended for riding, and users should wear an ASTM F1492 approved helmet and protective gear to prevent injury in the event of an accident.

Product Usage Instructions

Getting Started

To insert or remove the stem:

1. Press the stem release button and hold it down.
2. While holding down the stem release button, pull up on the stem to remove it from the stem mount.
3. To insert the stem, align it with the stem mount and push it down until it clicks into place.
4. TO INSERT THE STEM, PLACE THE STEM OVER THE STEM MOUNT SUCH THAT THE BLACK BUTTON IS FACING THE BACK OF THE SCOOTER. PUSH IN THE BUTTON AND SLIDE THE STEM DOWN INTO THE STEM MOUNT UNTIL THE BUTTON CLICKS INTO THE HOLE IN THE SCOOTER BASE.
5. TO REMOVE STEM, PRESS IN THE BUTTON ON THE STEM MOUNT AND PULL THE STEM UP.

To adjust handlebar height:

1. Twist the knob counterclockwise to loosen the stem clamp.
2. Open the stem clamp lever.
3. Press in the stem pin and raise or lower the handlebar until the pin clicks into another stem pin hole.
4. Close the stem clamp lever and twist the knob clockwise to tighten the clamp and secure the handlebar in place.

IMPORTANT : THE STEM PIN ALONE WILL NOT KEEP THE STEM SECURE. ALWAYS MAKE SURE THE STEM CLAMP IS TIGHTENED AND CLOSED PRIOR TO RIDING.

NOTE : DO NOT OVER-TIGHTEN THE KNOB. OVER-TIGHTENING CAN PREVENT THE LEVER FROM OPENING AND CLOSING WITH EASE.

Always make sure the stem clamp is tightened and closed prior to riding. Do not over-tighten the knob as it can prevent the lever from opening and closing with ease.

Making Moves

To ride the scooter:

1. Place one foot on the front of the deck facing forward.
2. Push the other foot off the ground to propel the scooter forward. Repeat as necessary to achieve or maintain desired speed.
3. To coast, place your kicking foot on the rear of the deck, turned outward at a slight angle for stability.

Using the Brake
PRESS DOWN GENTLY WITH YOUR REAR RIDING FOOT TO SLOW DOWN. APPLY MORE PRESSURE TO COME TO A COMPLETE STOP.

Making Turns
THE SCOOTER IS A LEAN TO STEER SCOOTER. TO TURN, SLIGHTLY LEAN LEFT OR RIGHT WHILE RIDING AND THE SCOOTER WILL VEER ACCORDINGLY.

Activating the LED Lights
THE WHITE LED LIGHTS ON THE FRONT AND REAR WHEELS WILL ILLUMINATE WHENEVER THE WHEELS ARE IN MOTION.

Decorating your Scooter
DECORATE YOUR SCOOTER! JUST PEEL OFF YOUR FAVORITE STICKERS AND CUSTOMIZE THE STEM OF YOUR NEW RIDE.

NOTE : FOR SAFETY AND DURABILITY, ONLY PUT STICKERS ON THE SCOOTER’S STEM—NOT THE DECK, HANDLEBAR GRIPS, OR WHEELS.

Helmet Safety

• PROPER POSITIONING : THE FOREHEAD IS COVERED BY THE HELMET.
• IMPROPER POSITIONING : THE FOREHEAD IS EXPOSED. A FALL COULD RESULT IN SERIOUS INJURY.
• WEAR A HELMET, APPROPRIATE CLOTHING, SHOES, AND SAFETY GEAR. AVOID CLOTHING THAT CAN GET CAUGHT INTO OR UNDER THE WHEELS. CLOSED-TOE, FLAT SHOES ARE RECOMMENDED. WEAR AN ASTM F1492 APPROVED HELMET AND PROTECTIVE GEAR TO PREVENT INJURY IN THE EVENT OF AN ACCIDENT.

To use the brake, press down gently with your rear riding foot to slow down. Apply more pressure to come to a complete stop. The scooter is a lean-to-steer scooter. To turn, slightly lean left or right while riding, and the scooter will veer accordingly. To activate the LED lights, ride the scooter so that the wheels are in motion. To decorate your scooter, peel off your favorite stickers and customize the stem of your new ride. Only put stickers on the scooter’s stem and not on the deck, handlebar grips, or wheels.

Puzzle fun! Can you identify which sticker matches with each silhouette? (Hope you don’t get too stuck on this.) Best of luck!

Safety Warnings

• Before use, please read the user manual and safety warnings carefully, and make sure you understand and accept all the safety instructions. The user will be responsible for any loss or damage caused by improper use.
• Before each cycle of operation, the operator shall perform the preoperation checks specified by the manufacturer: That all guards and pads originally supplied by the manufacturer are in proper place and in serviceable condition; That the braking system is functioning properly; That any and all axle guards, chain guards, or other covers or guards supplied by the manufacturer are in place and in serviceable condition; That tires are in good condition, inflated properly, and have sufficient tread remaining; The area that the product is to be operated should be safe and suitable for safe operation.
• Components shall be maintained and repaired in accordance with the manufacturer’s specifications and using only the manufacturer’s authorized replacement parts with installation performed by dealers or other skilled persons.
• Warning against recharging non-rechargeable batteries.
• Don’t allow hands, feet, hair, body parts, clothing, or similar articles to come in contact with moving parts, wheels, or drive train, while the motor is running.
• This product should not be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction (IEC 60335-1/A2:2006).
• Unsupervised children should not play with the product (IEC 60335-1/A2:2006).
• Adult supervision is required.
• The rider should not exceed 110 lb.
• Units shall not be operated to perform racing, stunt riding, or other maneuvers, which may cause loss of control, or may cause uncontrolled operator/passenger actions or reactions.
• Never use near motor vehicles.
• Avoid sharp bumps, drainage grates, and sudden surface changes. Scooter may suddenly stop.
• Avoid streets and surfaces with water, sand, gravel, dirt, leaves, and other debris. Wet weather impairs traction, braking, and visibility.
• Avoid riding around flammable gas, steam, liquid, or dust that could cause fire.
• Operators shall adhere to all of the manufacturer’s recommendations and instructions, as well as comply with all laws and ordinances: Units without headlights shall be operated only with adequate daylight conditions of visibility, and; Owners shall be encouraged to highlight (for conspicuity) using lighting, reflectors, and for low-riding units, signal flags on flexible poles.
• Persons with the following conditions shall be cautioned not to operate: Those with heart conditions; Pregnant women; Persons with head, back, or neck ailments, or prior surgeries to those areas of the body; and persons with any mental or physical conditions that may make them susceptible to injury or impair their physical dexterity or mental capabilities to recognize, understand, and perform all of the safety instructions and to be able to assume the hazards inherent in unit use.
• Do not ride at night.
• Do not ride after drinking or taking prescription medication.
• Do not carry items when riding.
• Never operate the product barefooted.
• Always wear shoes and keep shoelaces tied.
• Make sure your feet are always placed securely on the deck.
• Operators always shall use appropriate protective clothing, including but not limited to a helmet, with appropriate certification, and any other equipment recommended by the manufacturer: Always wear protective equipment such as helmet, knee pads, and elbow pads.
• Always give way to pedestrians.
• Be alert to things in front and far away from you.
• Do not allow distractions when riding, such as answering the phone or engaging in any other activities.
• The product cannot be ridden by more than one person.
• When you ride the product along with other riders, always keep a safe distance to avoid a collision.
• When turning, be sure to maintain your balance.
• Riding with improperly adjusted brakes is dangerous and can result in serious injury or death.
• The brake may become hot while operating, do not touch the brake with your bare skin.
• Applying brakes too hard or too suddenly can lock up a wheel, which could cause you to lose control and fall. Sudden or excessive application of the brake may result in injury or death.
• If the brake loosens, please adjust with the hexagon wrench, or please contact the Jetson Care Team.
• Replace worn or broken parts immediately.
• Check whether all safety labels are in place and understood before riding.
• The owner shall allow the use and operation of the unit after a demonstration that such operators can understand and operate all components of the unit before use.
• Do not ride without proper training. Do not ride at high speeds, on uneven terrain, or on slopes. Do not perform stunts or turn abruptly.
• Recommended for indoor use.
• Prolonged exposure to UV rays, rain and the elements may damage the enclosure materials, store indoors when not in use.

WARNING:

This product can expose you to chemical Chromium, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

MODIFICATIONS
Do not attempt to disassemble, modify, repair, or replace the unit or any components of the unit without instruction from the Jetson Care Team. This will void any warranty, and can lead to malfunctions which may cause injury.

ADDITIONAL OPERATION PRECAUTIONS
Do not lift the product off the ground while it is on and the wheels are in motion. This can result in freely spinning wheels, which may cause injury to yourself or others nearby. Do not jump on or off the product, and do not jump while using it. Always keep your feet firmly planted on the foot rest while in operation.

Product Overview

1. HANDLEBAR
2. STEM CLAMP
3. STEM
4. STEM MOUNT
5. STEM RELEASE BUTTON
6. FRONT WHEEL (MOTION-ACTIVATED LED LIGHT-UP)
7. DECK
8. REAR FOOT BRAKE
9. REAR WHEEL (MOTION-ACTIVATED LED LIGHT-UP)
10. STICKER PACKS

TOOL INCLUDED (FOR ADJUSTMENT AND MAINTENANCE):

2-BIT PHILLIPS-HEAD SCREWDRIVER AND ALLEN KEY TOOL ADULTS MUST ASSIST CHILDREN IN THE ASSEMBLY AND INITIAL ADJUSTMENT PROCEDURES OF THE PRODUCT.

NOTE : IMAGES MAY NOT REFLECT EXACT APPEARANCE OF ACTUAL PRODUCT.

Specs & Features

SPECS

• WHEEL SIZES : 4.7” (FRONT), 3.5” (REAR)
• PRODUCT DIMS : 23.4” (L) × 11.3” (W) × 25.9” (H)
• DECK SIZE : 23” (L) × 5.6” (W)
• HANDLEBAR HEIGHT : 25.9” – 30.7”
• WEIGHT LIMIT : 110 LBS
• PRODUCT WEIGHT : 5.5 LBS
• RECOMMENDED AGE : 3+

FEATURES

• REAR FOOT BRAKE
• LED LIGHT-UP WHEELS
• REMOVABLE STEM
• STICKERS FOR CUSTOMIZATION

Online Resources

Scan for our most updated scooter onboarding materials and support resources.

WARNING:
FAILURE TO COMPLY WITH THE FOLLOWING INSTRUCTIONS MAY RESULT IN INJURY TO THE CHILD OR OTHERS.

• KEEP SMALL PARTS AWAY FROM CHILDREN DURING ASSEMBLY.
• ACCESSORY MUST BE ASSEMBLED AND REMOVED BY AN ADULT.
• FREQUENTLY INSPECT THE PRODUCT FOR DAMAGE.

ADULTS MUST ASSIST CHILDREN IN THE ASSEMBLY AND INITIAL ADJUSTMENT PROCEDURES OF THE PRODUCT.

Care & Maintenance

CLEANING YOUR SCOOTER

• TO CLEAN YOUR SCOOTER, CAREFULLY WIPE WITH IT A DAMP CLOTH AND THEN WITH A DRY CLOTH.
• DO NOT APPLY WATER DIRECTLY TO THE SCOOTER. WATER CAN DAMAGE THE FRAME, WHICH CAN RESULT IN A MALFUNCTION THAT PUTS RIDER SAFETY AT RISK.

MAINTAINING YOUR SCOOTER

• KEEP AWAY FROM FIRE AND EXCESSIVE HEAT.
• AVOID INTENSE PHYSICAL IMPACT AND/OR SEVERE VIBRATION.
• RIDE THE SCOOTER ON A SMOOTH, FLAT SURFACE.
• PROTECT FROM WATER OR MOISTURE.
• CONTACT THE JETSON CARE TEAM IF THERE ARE ANY ISSUES WITH YOUR SCOOTER.

STORING YOUR SCOOTER

• STORE YOUR SCOOTER INDOORS AND IN A DRY PLACE.
• COVER YOUR SCOOTER TO PROTECT IT AGAINST DUST.

Warranty

ONE-YEAR GENERAL LIMITED WARRANTY
All new Jetson products are warranted against defects in materials and workmanship for a period of one year from the date of original retail purchase when used in accordance with Jetson’s user manuals (refer to ridejetson.com/support). Under this warranty, you will be able to direct your claims to Jetson even in situations where you purchased the Jetson Product from one of our authorized retailers. To read the full terms of our warranty, visit ridejetson.com/warranty.

Stay connected. Be sure to follow @ridejetson on social media to learn about fantastic offers, giveaways, and all the latest Jetson news.

Loving your ride?
Then be sure to leave a review at ridejetson.com/reviews. We can’t wait to hear from you!

Questions? Let us know.
ridejetson.com/support
ridejetson.com/chat

To exercise your product’s 1-year limited warranty or inquire about warranty coverage, contact us directly.

• US/CANADA : 1-888-976-9904
• MEX: +001 888 976 9904
• UK : +44 (0)33 0838 2551

Manufactured in Yongkang, China Imported by Jetson Electric Bikes LLC. P.O. Box 320149, 775 4th Ave #2, Brooklyn, NY 11232 www.ridejetson.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>