ZKTeco MTS1000 Pedestrian Turnstile User Manual
- June 13, 2024
- ZKTECO
Table of Contents
User Manual
mTS1000 Series Tripod Turnstile
Date: December 2021 Doc
Version: 1.0
MTS1000 Pedestrian Turnstile
Thank you for choosing our product. Please read the instructions carefully
before operation. Follow these instructions to ensure that the product is
functioning properly. The images shown in this manual are for illustrative
purposes only.
For further details, please visit our Company’s website
www.zkteco.com.
Copyright © 2021 ZKTECO CO., LTD. All rights reserved.
Without the prior written consent of ZKTeco, no portion of this manual can be
copied or forwarded in any way or form. All parts of this manual belong to
ZKTeco and its subsidiaries (hereinafter the “Company” or “ZKTeco”).
Trademark
is a registered trademark of ZKTeco. Other trademarks involved in
this manual are owned by their respective owners.
Disclaimer
This manual contains information on the operation and maintenance of the
ZKTeco equipment. The copyright in all the documents, drawings, etc. in
relation to the ZKTeco supplied equipment vests in and is the property of
ZKTeco. The contents hereof should not be used or shared by the receiver with
any third party without express written permission of ZKTeco.
The contents of this manual must be read as a whole before starting the
operation and maintenance of the supplied equipment. If any of the content(s)
of the manual seems unclear or incomplete, please contact ZKTeco before
starting the operation and maintenance of the said equipment.
It is an essential pre-requisite for the satisfactory operation and
maintenance that the operating and maintenance personnel are fully familiar
with the design and that the said personnel have received thorough training in
operating and maintaining the machine/unit/equipment. It is further essential
for the safe operation of the machine/unit/equipment that personnel has read,
understood and followed the safety instructions contained in the manual.
In case of any conflict between terms and conditions of this manual and the
contract specifications, drawings, instruction sheets or any other contract-
related documents, the contract conditions/documents shall prevail. The
contract specific conditions/documents shall apply in priority.
ZKTeco offers no warranty, guarantee or representation regarding the
completeness of any information contained in this manual or any of the
amendments made thereto. ZKTeco does not extend the warranty of any kind,
including, without limitation, any warranty of design, merchantability or
fitness for a particular purpose.
ZKTeco does not assume responsibility for any errors or omissions in the
information or documents which are referenced by or linked to this manual. The
entire risk as to the results and performance obtained from using the
information is assumed by the user.
ZKTeco in no event shall be liable to the user or any third party for any
incidental, consequential, indirect, special, or exemplary damages, including,
without limitation, loss of business, loss of profits, business interruption,
loss of business information or any pecuniary loss, arising out of, in
connection with, or relating to the use of the information contained in or
referenced by this manual, even if ZKTeco has been advised of the possibility
of such damages.
This manual and the information contained therein may include technical, other
inaccuracies or typographical errors. ZKTeco periodically changes the
information herein which will be incorporated into new additions/amendments to
the manual. ZKTeco reserves the right to add, delete, amend, or modify the
information contained in the manual from time to time in the form of
circulars, letters, notes, etc. for better operation and safety of the
machine/unit/equipment. The said additions or amendments are meant for
improvement /better operations of the machine/unit/equipment and such
amendments shall not give any right to claim any compensation or damages under
any circumstances.
ZKTeco shall in no way be responsible (I) in case the machine/unit/equipment
malfunctions due to any non-compliance of the instructions contained in this
manual (ii) in case of operation of the machine/unit/equipment beyond the rate
limits (iii) in case of operation of the machine and equipment in conditions
different from the prescribed conditions of the manual.
The product will be updated from time to time without prior notice. The latest
operation procedures and relevant documents are available on
http://www.zkteco.com
If there is any issue related to the product, please contact us.
ZKTeco Headquarters
Address| ZKTeco Industrial Park, No. 32, Industrial Road,
Tangxia Town, Dongguan, China.
---|---
Phone| +86 769 – 82109991
Fax| +86 755 – 89602394
For business-related queries, please write to us at:
sales@zkteco.com.
To know more about our global branches, visit
www.zkteco.com.
About the Company
ZKTeco is one of the world’s largest manufacturers of RFID and Biometric
(Fingerprint, Facial, Finger-vein) readers. Product offerings include Access
Control readers and panels, Near & Far-range Facial Recognition Cameras,
Elevator/floor access controllers, Turnstiles, License Plate Recognition (LPR)
gate controllers and Consumer products including battery-operated fingerprint
and face-reader Door Locks. Our security solutions are multi-lingual and
localized in over 18 different languages. At the ZKTeco state-of-the-art
700,000 square foot ISO9001-certified manufacturing facility, we control
manufacturing, product design, component assembly, and logistics/shipping, all
under one roof.
The founders of ZKTeco have been determined for independent research and
development of biometric verification procedures and the productization of
biometric verification SDK, which was initially widely applied in PC security
and identity authentication fields. With the continuous enhancement of the
development and plenty of market applications, the team has gradually
constructed an identity authentication ecosystem and smart security ecosystem,
which are based on biometric verification techniques. With years of experience
in the industrialization of biometric verifications, ZKTeco was officially
established in 2007 and now has been one of the globally leading enterprises
in the biometric verification industry owning various patents and being
selected as the National High-tech Enterprise for 6 consecutive years. Its
products are protected by intellectual property rights.
About the Manual
This manual introduces the operations of mTS1000 Series of Tripod Turnstiles.
All figures displayed are for illustration purposes only. Figures in this
manual may not be exactly consistent with the actual products.
Features and parameters with ★ are not available in all devices.
Document Conventions
Conventions used in this manual are listed below:
GUI Conventions
For Software
Convention| Description
Bold font| Used to identify software interface names e.g., OK, Confirm,
Cancel.
| Multi-level menus are separated by these brackets. For example, File > Create >
< >| Button or key names for devices. For example, press
Folder.
For Device
Convention| Description. [ ]| Window names, menu items, data table, and field names are inside square brackets. For example, pop up the [New User] window. /| Multi-level menus are separated by forwarding slashes. For example, [File/Create/Folder].
Symbols
| Convention | Description |
|---|---|
| This represents a note that needs to pay more attention to. | |
| The general information which helps in performing the operations faster. | |
| The information which is significant. | |
| Care taken to avoid danger or mistakes. | |
| The statement or event that warns of something or that serves as a |
cautionary example.
Overview
The mTS1000 Series is one kind of ZKTeco’s innovative semi-automatic tripod
turnstile series, it is made of SUS304 Stainless Steel, with the acrylic panel
on the top, which is beautiful in appearance and clean and is anti-rust. The
top cover panel of the mTS1000 Series integrated general access control is
customizable according to different verification modes. The mTS1000 Series
runs smoothly and quietly and consumes little power thanks to its small and
compact body design.
The mTS1000 Series tripod arms are normally held in a locked position, it
grants legal access to the authorized persons and restricts illegal access.
When a valid Card/Fingerprint ★ is detected, arms unlock and automatically
rotate at a slight push. During emergencies and power outages the tripod arms
completely collapse, the lock will release to allow fast evacuation and
egress, thereby ensuring users FAST unencumbered exit to safety. When the
power is on, the arm will automatically lift up to form a secure lane.
1.1 Features
Design: Compact body, the device run smoothly, silently and consumes
little power.
Count Statistics: Support the count of the number of people Inbound and
Outbound.
Verification Modes: Multiple authentication methods, convenient and
secure.
Gate Function: Supports anti-passback and fire mode.
1.2 Appearance and System Components
1.2.1 Appearance
The appearance and dimensions of the mTS1000 Series are shown in the figure
below:
1.2.2 System Components
The system components of the mTS1000 Series are shown below:
| 1. Direction Indicator | 2. Arm |
|---|---|
| 3. Verification Units | 4. Disk Wheel |
1.3 Mechanical System
The mechanical system of the tripod turnstile includes the chassis and the
core component. The chassis is a carrier where the Direction indicator,
Reader, Fingerprint sensor★ and the Door lock are installed. The core
component mainly consists of the Frame, Bearing, and Arm.
1.4 Electronic Control System
The electronic control system of a tripod turnstile is mainly composed of the
Card Reader/Fingerprint sensor★, Turnstile control board and Direction
Indicator.
Reader: The reader reads the data in the card and sends it to the Access
Controller.
Fingerprint sensor ★: The device compares the fingerprint that is being
pressed onto the fingerprint sensor with all the fingerprint data and sends it
to the Access Controller.
Turnstile control board: The turnstile control board is the system’s
control center that receives signals from the reader and the photoelectric
switch performs logical calculation and processing of these signals and sends
executive commands to the Direction indicator and arm.
Direction Indicator: This indicator displays the pedestrian passage path
and directs them to pass through the lane in a safe and orderly manner.
1.5 Working Principle
- After powering on to the device, the system performs the Power-On Self-Test.
- When a valid Card/Fingerprint★ is detected, the buzzer will give a positive audible prompt to the pedestrian, indicating that, it is successfully verified. And then, the reader sends signals to the Access Controller to request permission to pass through the passage. The Access Controller will send the signal to the master control panel.
- After receiving the signal from the Access Controller, the turnstile control board sends valid control signals to the direction indicator and the arm. At last, the direction arrow turns green.
- Pedestrians according to the directional signs, gently pushes the unlocked arm and then the arm will automatically rotate until the pedestrian pass through the channel.
- If the pedestrian enters the passage but forgets to verify identification, or if the card held/fingerprint★ by the pedestrian is invalid, the system does not allow pass. The pedestrian can pass through the passage only after a valid card/fingerprint★ is successfully verified.
1.6 Working Modes of the System
To make the product more versatile, this system provides 2 working modes for
the user, including
Normally Open Mode and Normally Close Mode.
Normal Open Mode: In this working mode, the arm falls.
Normal Close Mode: In this working mode, the arm is locked.
1.7 Technical Specifications
| Feature | Specification |
|---|---|
| Communication | TCP/IP, RS485 |
| Input Voltage | AC110V/220V, 50/60Hz |
| Input Control Signal | Switching Signal |
| Output Voltage | DC 24V |
| Protection Level | IPX3 |
| Time of Gate Opening/Closing | Minimum 0.6 Second |
| Operating Humidity | ＜93% (Non-condensing) |
| Operating Temperature | -20°C to 70°C |
| Flow Rate | Maximum 25/minute |
| Proximity Switch | Three pairs |
| Working Environment | Indoor/Outdoor (if sheltered) |
| MCBF | 2 million |
| Working Power | 40W |
| Standby Power | 10W |
| Dimension (mm) (LWH) | 798750950 |
| Noise | ＜60dB |
| Certifications | CE and FCC |
Function Introduction
2.1 Fingerprint Verification★
In this verification mode, the device compares the fingerprint that is being
pressed onto the fingerprint reader with all the fingerprint data sends it to
the Access Controller.
The device enters the fingerprint authentication mode when a user presses
his/her finger onto the fingerprint scanner.
Recommended fingers: It is recommended to use index,
middle, or ring finger for registration and avoid using the thumb or little
finger, as they are difficult to accurately press onto the fingerprint
reader.
Note: Please use the correct
method when pressing your fingers onto the fingerprint reader for registration
and identification. Our company will assume no liability for recognition
issues that may result from incorrect usage of the product. We reserve the
right of final interpretation and modification concerning this point.
2.2 Card Verification
The Card Verification mode compares the card number in the card induction area
with all the card number data registered in the device and sends it to the
Access Controller.
The device enters the card authentication mode when a user presses his/her
card to the card reading area.
2.3 Wired Remote Control★
The wired remote control has five buttons, which are the Left button, Right
button, Down button, Lock button, and Reset button. These five independent
buttons have individual functions as well as combined functions. Pressing two
buttons within the specified time interval can call up a predefined
mode.
- Independent functions:
| Press the button once to open the tripod turnstile and can pass by identity verification from the inbound.
---|---
| Press the button once to open the tripod turnstile and can pass by identity verification from the outbound.
| In emergency mode, press the button once to fall the arm lever. Then the inbound and outbound sides get open and can pass freely without identity verification.
| Press the button once to raise the arm lever. Then the inbound and outbound sides are controlled by the tripod turnstile. The identity verification becomes invalid, and no pass is allowed.
| Press a button once to restore the default inbound and outbound identity verification pass mode of the arm. - Combined functions:**
Status| Description**
---|---
Inbound free, Outbound control| Press “ ” twice to open the tripod turnstile on both sides. The inbound side is free to allow people without identity verification and can pass by identity verification from the outbound.
Inbound control, Outbound free| Press “ ” twice to open the tripod turnstile on both sides. The outbound side is free to allow people without identity verification and can pass by identity verification from the inbound.
Inbound free, Outbound free| Press “ ” and “ ” at the same time to open the tripod turnstile on both sides and both inbound and outbound sides can pass freely without identity verification.
Inbound forbidden, Outbound free| First press “ ” once, and then press “ ” once, then the inbound side is forbidden to go through, and the outbound side is free for all to pass without identity verification.
Inbound free, Outbound forbidden| First press “ ” once, and then press “ ” once, then the outbound side is forbidden to pass, and the inbound side is free for all to pass without identity verification.
Inbound control, Outbound forbidden| First press “ ” once, and then press “ ” once, then the outbound side is forbidden to pass, and the inbound side needs for identity verification to pass.
Inbound forbidden, Outbound control| First press “ ” once, and then press “ ” once, then the inbound side is forbidden to pass, and the outbound side needs for identity verification to pass.
The wired remote control is connected to the controller, then set the controller’s code pairing mode to complete the wired remote control’s setup.
Dial code description:
The DIP switch is divided in eight dial codes from KE-1 to KE-8. Move the
switch up to turn ON and down to turn OFF.
Description of Function Setting:
- Dial 0 to turn OFF.
- Dial 1 to turn ON.
Dial code function item:
-
Unmanned passage time (KE-1, KE-2, KE-3):
Switch Status| Time Period
---|---
000 (OFF OFF OFF)| 5s (Default)
001 (OFF OFF ON)| 10s
010 (OFF ON OFF)| 15s
011 (OFF ON ON)| 20s
100 (ON OFF OFF)| 30s
101 (ON OFF ON)| 40s
110 (ON OFF ON)| 50s
111 (ON ON ON)| 60s -
Memory Swipe Mode (KE-6):
Dial 1 (ON) to turn on.
Dial 0 (OFF) to turn off. -
Turn on Alarm Mode (KE-8):
Dial 1 (ON) to turn on.
Dial 0 (OFF) to turn off.
2.4 Wireless Remote Control★
The wireless remote control of the tripod turnstile is an intelligent device
that remote controls the entrance and exit. It is designed for manual control
of the tripod turnstile by the administrator. The wireless remote control has
four buttons A, B, C, and D, corresponding to the options open entrance gate,
open exit gate, emergency mode open-bar pass, and alarm lock.
| Buttons | Description |
|---|---|
| A | Press the button once to open the tripod turnstile on the inbound and can |
allow people to pass through after identity verification from the inbound.
B| Press the button once to open the tripod turnstile on the outbound and can
allow people to pass after their identity verification from the outbound.
C| In emergency mode, press the button once to fall the arm lever. Then the
inbound and outbound sides get open and people can pass freely without
identity verification.
D| Press the button once to raise the arm lever. Then the inbound and outbound
sides are controlled by the tripod turnstile. The identity verification
becomes invalid, and no pass is allowed.
When the controller is powered on, the wireless remote control is not in
communication with the controller. Press and hold the DIP switch of the
controller to enter the code pairing mode and operate the remote control
according to the eight DIP switch codes of the controller.
To code:
- First, power the controller of the tripod turnstile.
- Short press the learning button on the controller, and a light corresponding to the button will flash slowly. Then press any switch on the remote control for acquiring the information. After the successful operation, the light turns off.
Clear code:
Long press the learning button on the three-roller gate controller for 3
seconds. The learning light stays on for a while then turns off indicating the
code is cleared successfully. The original learning remote control cannot be
used again and can only be remote-controlled by the code again.
Wiring Diagram
Packing List
The package consists of the following items:
| mTS1000| 1
---|---|---
| Power cable| 1
| Card| 1
| Expansion Screw M12*100| 4
| Stainless Steel Maintenance Wipes| 1
| Hex wrench| 1
| Allen Screw| 3
| Key| 2
| Washer| 3
www.zkteco.eu
Copyright©2021 ZKTECO CO., LTD. All Rights Reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>