JETSON TBH Volt LED Strip Lights User Guide

JETSON TBH Volt LED Strip Lights

Safety Warnings

• Keep these instructions.
• Non-user replaceable light sources.
• Uncoil the light strip before use.
• Do not drop, puncture, open, cut, or disassemble this product.
• Do not install this product in any way other than what is outlined in this guide.
• Do not place this device on hot surfaces.
• Only use the adaptor supplied; using a different adaptor can damage the device.
• Do not submerge the strip or the power supply unit in water.
• Avoid long exposure to direct sunlight, which may cause damage.
• Do not use this product in small, enclosed locations that could limit the flow of air or trap excess heat.
• Do not expose this product to open flames or use near fire.
• Do not use the product in a strong magnetic field.
• Do not use this product for emergency lighting/exits.
• Do not allow small children to operate, modify, or install this device unsupervised.
• Use a clean, soft cloth to clean – do not use any cleaning agents to clean.
• Manage in accordance with disposal laws in your area.
• Do not clean the device when it is on and connected to the power supply.
• Do not connect the light strip to the power supply while in its packaging or wound onto its reel.
• Do not use the rope light when covered or recessed into a flat surface.
• Not intended for illumination; only use for ambience.

WARNING: This product can expose you to a chemical such as Cadmium that is known to the state of California to cause cancer or birth defects or other reproductive harm. For more information go to
www.p65warnings.ca.gov/product

NOTICE OF COMPLIANCE

Changes or modifications not expressly approved by Jetson could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit  from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

LIMITED 1 YEAR WARRANTY

Limited 1 Year Warranty only applies to the manufacturer defects. Contact Jetson Customer Care for detailed information via support. ridejetson.com
Limited 1 Year Warranty does NOT cover:

• Normal wear and tear
• Improper assembly
• Corrosion
• Improper maintenance
• Installation of components, parts, or accessories not originally intended for or compatible with the product as sold
• Damage or failure due to accident, misuse, abuse, or neglect
• Labor charges for part replacement or changeover
• Non-proprietary products (any other original part or component) covered by the original manufacturer’s warranty
•  Any accessories

Specs & Features

• POWER SUPPLY: 12V AC ADAPTER
• OUTPUT POWER: 16FT=12W, 32FT=24W 64FT=36W
• OPERATING TEMPERATURE: BETWEEN -4F AND 113F
• REMOTE CONTROL RANGE: UP TO 26FT
• REMOTE CONTROL BATTERY: CR2025 OR EQUIVALENT
• IP20 NON WATER RESISTANT – FOR INDOOR USE ONLY

What’s in the Box

1. LED STRIP LIGHTS
2. REMOTE
3. CONTROLLER
4. AC ADAPTER
5. MOUNTING ADHESIVE

Get Started

Preinstallation

CHECK THAT YOU HAVE EVERYTHING. BOX SHOULD CONTAIN AMBER VOLT STRIP, CONTROLLER, AC ADAPTER, REMOTE CONTROL AND MOUNTING ADHESIVE.

Installing Your Lights

• WIPE DOWN AND CLEAN THE SURFACE YOU’RE PLANNING TO PLACE YOUR LIGHTS ON.
• PEEL OFF THE PROTECTIVE TAPE ON THE BACK OF THE LIGHTS.
• PLACE LIGHTS ONTO SURFACE. PRESS DOWN TO MAKE SURE ADHESIVE IS FIRMLY SECURED TO SURFACE.
• INSERT THE CONTROLLER INTO THE LIGHTS. ENSURE THAT ARROWS LINE UP CORRECTLY.
• INSERT THE AC ADAPTER INTO THE CONTROLLER.
• PLACE POWER ADAPTER INTO ELECTRICAL OUTLET.

How To Control Your Lights

Controlling with the Controller

Controlling with the Remote

•  CONTROL AND CUSTOMIZE YOUR AMBER LIGHTS USING THE INCLUDED REMOTE.

CREATING CUSTOM COLORS:

1. PRESS EITHER THE ‘DIY1’, ‘DIY2’, OR ‘DIY3’ BUTTONS.
2. PRESS THE ‘DOWN’ BUTTON IN EITHER RED, GREEN, OR BLUE TO CHANGE THE LED LIGHTS FROM THE DEFAULT COLOR (WHITE).
3. CONTINUE TO ADJUST EITHER RED, GREEN, OR BLUE BY PRESSING THE ‘UP’ OR ‘DOWN’ BUTTONS UNTIL YOU REACH YOUR PREFERRED COLOR.
4. PRESS THE SAME ‘DIY’ BUTTON THAT YOU DID IN STEP 1. YOUR COLOR IS NOW SAVED, AND CAN BE RETRIEVED BY PRESSING THE SAME ‘DIY’ BUTTON AT ANY TIME.

NOTE: YOU CAN NOW USE ADDITIONAL EFFECTS BUTTONS, SUCH AS ‘FADE’. TO RETURN YOUR PREFERRED COLOR WITHOUT THESE FUNCTIONS, PRESS THE RELEVANT
‘DIY’ BUTTON.

Controlling with the App

•  CONTROL YOUR AMBER VOLT RIGHT FROM YOUR PHONE. JUST SCAN THE QR CODE TO DOWNLOAD THE APP THROUGH THE APP STORE.

References

• Electric Bikes, Scooters, Hoverboards and More - Jetson
• Product Reviews
• p65warnings.ca.gov/product
• Electric Bikes, Scooters, Hoverboards and More

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>