JETSON ALIT-3 LED Strip Lights User Guide

: June 4, 2024
: Jetson

Table of Contents

Safety Warnings
Specs & Features
Get Started
Operating the Motion Sensor
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

Lit
LED Strip Lights.

A guide for your lights.
IMPORTANT: READ CAREFULLY, RETAIN FOR FUTURE REFERENCE.
MODEL: ALIT-3 | ALIT-6 | ALIT-9

Safety Warnings

Keep these instructions.
Nonuser replaceable light sources.
Uncoil the light strip before use.
Do not drop, puncture, open, cut, or disassemble this product
Do not install this product in any way other than what is outlined in this guide.
Do not place this device on hot surfaces.
Only use the adaptor supplied; using a different adaptor can damage the device.
Do not submerge the strip or the power supply unit in water.
Avoid long exposure to direct sunlight, which may cause damage
Do not use this product in small, enclosed locations that could limit the flow of air or trap excess heat.
Do not expose this product to open flames or use near fire.
Do not use the product in a strong magnetic field.
Do not use this product for emergency lighting/exits.
Do not allow small children to operate, modify, or install this device unsupervised.
Use a clean, soft cloth to clean – do not use any cleaning agents to clean.
Manage in accordance with disposal laws in your area.
Do not clean the device when it is on and connected to the power supply.
Do not connect the light strip to the power supply while it is in the packing or wound onto the reel.
Do not use the rope light when covered or recessed into a flat surface.
Not intended for illumination. Only use for ambiance.

California Proposition 65
WARNING:
This product can expose you to a chemical such as Cadmium which is known to the state of California to cause cancer or birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov/product
NOTICE OF COMPLIANCE
Changes or modifications not expressly approved by Jetson could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20 cm between the radiator & your body.
LIMITED 1-YEAR WARRANTY
Limited 1 Year Warranty only applies to the manufacturer defects. Contact Jetson Customer Care for detailed information via support. ridejetson.com
Limited 1 Year Warranty does NOT cover:

Normal wear and tear
Improper assembly
Corrosion
Improper maintenance
Installation of components, parts, or accessories not originally intended for or compatible with the product as sold
Damage or failure due to accident, misuse, abuse, or neglect
Labor charges for part replacement or changeover
Non-proprietary products (any other original part or component) covered by the original manufacturer’s warranty
Any accessories

Specs & Features

WATTS: 1.5W
BATTERY: RECHARGEABLE 1000MA/3.7V
CHARGER: DC5V MICRO USB
CHARGING TIME: UP TO 3 HOURS
SENSOR DISTANCE: UP TO 16.5FT
OPERATING TEMPERATURE: BETWEEN -4F AND 113F
LED STRIP WATER RESISTANCE RATING: IP44 SPLASHPROOF
MOTION SENSOR CONTROLLER WATER RESISTANCE

RATING: IP20 NOT WATER RESISTANT
What’s in the Box

LED STRIP LIGHTS
MOTION SENSOR CONTROLLER
USB CHARGING CORD
MOUNTING ADHESIVE

Get Started

1.1 Preinstallation

CHECK THAT YOU HAVE EVERYTHING. BOX SHOULD CONTAIN AMBER LIT STRIP, MOTION SENSOR CONTROLLER, USB CHARGING CORD, AND MOUNTING ADHESIVE.

1.2 Installing Your Lights

MAKE SURE THE MOTION SENSOR IS CHARGED USING THE USB INCLUDED.
AFTER IT IS CHARGED, PLUG THE END OF THE LIGHT STRIP INTO THE MOTION SENSOR PORT.
WIPE DOWN AND CLEAN THE SURFACE YOU’RE PLANNING TO PLACE YOUR LIGHTS ON.
THE CIRCULAR MAGNET INCLUDED WILL ATTACH TO THE BACK OF THE MOTION SENSOR CONTROLLER. SECURE THE 3M ADHESIVE INCLUDED TO THE EXPOSED SIDE OF THE MAGNET TO MOUNT TO THE WALL.
PEEL OFF THE PROTECTIVE TAPE ON THE BACK OF THE LIGHTS AND MAGNETIC MOTION SENSOR MOUNT.
PLACE LIGHTS ONTO SURFACE AND MOTION SENSOR ONTO MAGNET. PRESS DOWN TO MAKE SURE ADHESIVE IS FIRMLY SECURED TO SURFACE.

Operating the Motion Sensor

1. ‘RGB‘ KEY:

ENABLES ‘STATIC’ MODE, TOGGLE BETWEEN 21 DIFFERENT COLOR OPTIONS

2. ‘MODE’ KEY:

ENABLES ‘DYNAMIC’ MODE, CYCLES BETWEEN 8 DIFFERENT LIGHT FUNCTIONS

3. ‘+/-‘ KEY:

WHEN LIGHTS ARE STATIC, THIS CYCLES THROUGH

5 LEVELS OF BRIGHTNESS

WHEN LIGHTS ARE IN DYNAMIC MODE, THIS CYCLES THROUGH 5 LEVELS OF SPEED
PRESS AND HOLD FOR 1 SECOND TO TURN OFF

4. TIMER SWITCH:

ADJUST THE LENGTH OF TIME LIGHTS WILL POWER OFF AFTER NO MOTION IS DETECTED

5. OF:

MOVEMENT AND LIGHT SENSORS ARE OFF

6. SUN SWITCH:

MOTION SENSOR ENABLED – LIGHT WILL TURN ON WHEN IT DETECTS MOVEMENT

7. MOON SWITCH:

MOTION AND LIGHT SENSOR ENABLED: SENSOR WILL ONLY TURN ON WHEN IT DETECTS BOTH MOVEMENT AND LIGHT UP TO 2-5 LUX

*WARNING- WHEN BRIGHTNESS OF LIGHT BEGINS TO DULL IT INDICATES THE BATTERY POWER IS INSUFFICIENT, PLEASE CHARGE THE CONTROLLER IMMEDIATELY
Enjoying the ride?
Leave a review on ridejetson.com/reviews or share your photos with us online using the #RideJetson hashtag!

Follow us @ridejetson
#MakeMoves Questions? Let us know.
support.ridejetson.com
Hours of Operation:
7 Days a Week, 10 am-6 pm
Manufactured in Shenzhen, China
Imported by Jetson Electric Bikes LLC.
86 34th Street 4th Floor, Brooklyn, New York 11232
www.ridejetson.com
Designed in Brooklyn
Made in China
Date Code: 10/2021