ESR 2C566 HaloLock 3-in-1 Watch Wireless Charging Set User Manual
- June 9, 2024
- ESR
Table of Contents
ESR 2C566 HaloLock 3-in-1 Watch Wireless Charging Set
OVERVIEW
- HaloLock™ phone charging pad
- AirPods charging pad
- Status light
- USB-C port (input)
- USB-C port (output)
- 20W PD charging adapter
- USB-C-USB-C cable
Status Light Guide
| |
---|---|---
Charger Status| Power on| Charging| Fully charged/
Standby
| Error
detected
Light| On for 5
seconds
| On| Off| Flashing
If an error is detected
- Ensure that your phone supports wireless charging and that there are no credit cards, stands, or other attachments on the back that will interfere with charging.
- After checking the above, unplug and plug in the charging cable again to resume normal charging.
Important Reminders
- Use included adapter and cable to power charger.
- The charger supports an input of 9V/2.22A. Maximum output is 7.5W for iPhone, 5W for AirPods, and 5W for the Apple Watch charger. The USB-C port has a maximum output of 5W.
- The HaloLock™ charging pad only supports magnetic attachment with a careless iPhone with MagSafe, an official MagSafe case, an ESR HaloLock™ case, or a standard case with a HaloLock™ Universal Ring. It may not attach to other magnetic cases. It will not attach to any other non-magnetic phones or cases. (Over time, the charger may leave a faint circular mark on the back of your phone that can be easily cleaned with an alcohol wipe.)
- Charger must be plugged in to power supply to charge devices.
Safety Warnings
- Do not expose the device to temperatures below 0°C (32°F) or above 60°C (140°F).
- Do not expose the device to an open flame or submerge it in water as this will damage the device.
- Always check for damage to the device, cables, or other accessories before using the device. If damaged, do not use the device.
- Do not attempt to disassemble or modify the device in any way, as it may cause serious damage and void the warranty.
- Do not expose the device to corrosive liquids, or high humidity as they will seriously damage the device and void the warranty.
FCC ID:2APEW-2C566
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &your body.
IC:24790-2C566
This device complies with Industry Canada licence-exempt RSS standard( s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 10 centimeters between the radiator and your body. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
Declaration of Conformity
This product is intended for use within Europe. Electronic Silk Road Corp. hereby declares that this product 2C566 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU,2014/35/EU,2014/30/EU. The Declaration of Conformity for the 2C566 is available from www.esrgear.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>