MEMPHIS MXALEDFOB LED Accent kit Instruction Manual
- June 9, 2024
- MEMPHIS
Table of Contents
MXALEDFOB LED Accent kit
Instruction Manual
MXALEDFOB LED Accent kit
LED Accent kit Installation Guide
Prior to Installation Upon receiving your new light kit, please test the
kit first by temporarily connecting the red power wire to a 12 volt source and
the black ground wire to an unpainted exposed metal engine ground. Once the
wires are secured, power on the kit to ensure all led strips function prior to
installing. If all lights appear to be in working order, power down the kit in
preparation for installation.
Installation
Step l Begin by first laying the LED light strips in a manner similar to
the way you will install them. Take time to make certain the wires will be
able to be easily routed to their desired destination without being pinched,
cut or exposed to heat. CAUTION: Be sure to keep the wires and strips away
from all moving parts Take special caution to avoid steering components.
Step 2 Locate a dry accessible location to mount the control box. NOTE:
the control box is not waterproof, take caution to shelter it from the
elements. If the control box is exposed to water the device will fail. If any
water damage and /or corrosion occurs to the control box it will VOID all
warranties.
Step 3 Clean the proposed mounting surface with an alcohol prep pad or
equivalent cleaning solution. NOTE: The surface must be free of any oils,
moisture,dirt and wax in order for adhesive to properly bond. The mounting
surface must be between 45 to 85 Fahrenheit to achieve the best bond from the
double sided adhesive.
Step 4 Temporarily place lighting strips in the intended mounting
position and loosely route the wires to the planned control box mounting area.
Secure the wires to the desired mounting location using zip ties [ not
included ].
Step 5 Once wires are secured and you confirm the surface is clean and
dry, secure each strip by using the supplied double sided 3M adhesive tape.
Use wire ties at each end of the strip to act as a secondary anchor and
mounting point for each strip. NOTE: The wire ties are a very important step
and should not be skipped, they ensure the strips stay adhered and in place
while the vehicle is in use and during seasonal temperature changes. Once
these steps are complete and the strips are secure, allow ample time for
adhesive to settle and cure.
Step 6 Route the red power wire from the control box to a positive (+)12
volt source. Route the black ground wire to a well-known ground [-]location.
If the wires need to be extended to fit use automotive grade 14-16 GA wire for
the red and black power wires. Once everything is properly installed connect
the power supply lines. NOTE: Failure to properly mount all components prior
to connecting the power supply may cause the inline fuse on the red power wire
to blow.
Step 7 The kit was designed using a modular locking plug system for
connecting the LED lighting strips to the control box and vice versa. The
wires are not to be cut in an attempt to shorten or lengthen them. If the
wires or connectors are found to be cut or modified in any way, the
manufacturer warranty is null and void ANY alteration of the control box,
lighting strips or wires may impact kit functionality and void warranties
expressed or implied
Step 8 The LED Strips were designed to be cut to size if necessary. Use
caution and only cut along the predefined cut lines as indicated on the LED
strips Cutting outside of these lines will void warranty.
Step 9 See the included users guide for instructions on downloading the
required app to your device and for additional information on how to control
your new LED kit .
Optional Wired Remote Button The optional wired remote button can be
installed to control your unit without a Blue tooth device. To install the
remote attached the included remote button to the open connection in the led
harness. Run the wire to a convenient mounting location and mount the button
into Place.
Troubleshooting
If the kit or lights do not appear ta operate as intended first check the
installed inline mini fuse. If the fuse is blown, check the wires on the
entire kit to make sure that they are not cut, pinched or burned. Fix any
problem with the wires and retest. If there is no damage to any to the wires
and there is no water damage visible to the control box, replace the fuse and
test again. If the situation is not resolved, clean the battery terminals and
[+] and [-] connection points. Test kit again. If situation is not improved
please contact customer service at
800-489-2300.
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: 1. This device may not cause harmful
interference, and 2. This device must accept any interference received,
including interference that may cause undesired operation
CAUTION Any changes or modifications not expressly approved by the
manufacturer could void the user,s authority to operate this device
NOTE This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate
the receiving antenna.Increase the separation between the equipment and the
receiver. Consult the dealer or an experienced radio/TV technician for help.
SQLXILEDKITS
Tested To Comply With FCC Standards
FOR AFTERMARKET USE
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>