LED WORLD LIGHTING QS-RD-COB3W-12V 3W LED Puck Light Recessed Mount Instruction Manual

: June 9, 2024
: LED WORLD LIGHTING

Table of Contents

IMPORTANT INSTRUCTIONS
THREE YEAR LIMITED LIGHTING WARRANTY
LED PUCK LIGHT (Recessed/Surface Mounted)
RECESSED MOUNTING:
SURFACE MOUNTING:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LED WORLD LIGHTING QS-RD-COB3W-12V 3W LED Puck Light Recessed Mount

IMPORTANT INSTRUCTIONS

CAUTION: To reduce the risk of electric shock:

Use only insulated staples or plastic ties to secure cords.
Route the low voltage wire from the light so that they will not be damaged or pinched when the cabinet is installed (pushed to the wall).
Not intended for recessed ceiling installation or soffits.

Low voltage portable cabinet light maybe installed in furniture or cabinets when:

The power supply is located outside cabinets and is not concealed (this does not apply to the wiring between the light and the power supply).
When the low voltage wire are not concealed or pass through the structure of the building (concealed behind the wall) where it may be inaccessible for examination or where damage to may go unnoticed.
Cords should be visible and examined regularly.

Installation instructions:

Must be installed by a qualified licenced electrician.
Turn power off prior to installation.
Bore a hole Ø2.36” (60mm) minimum recess depth required 5/8” (15mm).
Route the low voltage wiring through the hole.
Insert the light into the hole; fiction fit light will lock in place.
Plug the light’s low voltage wiring into the class 2 LED power supply. (#MD-012-060VTDHV2, #MD-012-030VTDHV2 – sold separately).

WARNING: Always connect the LED light to the power supply first and then connect the power supply to the mains. Failure to do so may cause damage to the existing diode.

THREE YEAR LIMITED LIGHTING WARRANTY

LED WORLD INC. warranties this product for three year (some exceptions may apply) from the date of shipping unless otherwise noted in writing. This warranty is expressly in lieu of all other warranties expressed or implied. Under this Limited Warranty, the obligation of the company is limited to replacing on a prorated basis, at its option, any component found to be defective.

This Limited Warranty does not apply to damage caused by buyer or alteration to the product or incorrect power supply. Factory warrantees are covered by the original manufacturer and claims must be submitted to them.

LED World Inc. And its providers will never be liable to you or any other person for any indirect, incidental, consequential, special, punitive or exemplary loss or damage arising from, connected with, the purchase of products, including but not limited to loss of data, business, markets, cost of labour, savings, income, profits, use, production, reputation or goodwill, anticipated or otherwise, or economic loss, under any theory of liability (whether in contract, tort, strict liability or any other theory or law or equity), regardless of any negligence or other fault or wrongdoing (including without limitation gross negligence and fundamental breach) by led world inc. Or any person for whom led world inc. Is responsible, and even if led world inc. Has been advised of the possibility of such loss or damage being incurred.

If a product is defective, we will replace the product with similar or identical product or at our option a credit towards a future purchase. To make a claim under this warranty, obtain a return authorization number.

LED PUCK LIGHT (Recessed/Surface Mounted)

For Under Cabinet lighting and Under Counter Top Lighting

Serial Connection (Max. 10 pcs in a continuous run)

RECESSED MOUNTING:

Turn off the power at breaker
Drill a Ø60mm hole through cabinet or shelf, see fig 1.
Connect light to the Class 2 driver, see fig 2.
Insert the recessed puck light into the cut hole, see fig 1a.
Turn on the power.

SURFACE MOUNTING:

Turn off the power at breaker.
Take the surface mounting ring off the fitting, see fig 1b.
Mount the ring to surface with the attached screws, pay attention to the direction of the notch for the cord, see fig 1b.
Connect light to the Class 2 driver, see fig 2.
Insert the recessed puck light back into the surface mount ring, see fig 1b.
Turn on the power.