LED World Lighting LW-2812WI Multi Zone LED Controller Installation Guide

July 18, 2024
LED WORLD LIGHTING

LED World Lighting LW-2812WI Multi Zone LED Controller

Specifications

  • Manufacturer: HHUEDDAATMTM
  • Product: MultiZone LED Controller
  • Power Supply: Regulated constant voltage Class 2 power supply (12-24V DC Max)
  • Warranty: 3 Years Limited Manufacturer Warranty
  • Wire Gauge: 24 to 18 AWG for output terminals

Product Usage Instructions

Safety & Installation Warnings

  • Before installation, read all warnings and instructions provided.
  • Use only a regulated constant voltage Class 2 power supply within the specified voltage range to avoid damage and ensure safety.
  • Do not use dimmable or magnetic dimmable power sources with this product.
  • Install wires properly to prevent overheating and potential fire hazards.
  • Consult a qualified electrician for installation to comply with electrical codes.

Operation Overview

  • RGBW Control: Press to turn ON/OFF Red, Green, Blue, and White colors. Long press to adjust the brightness of individual colors.
  • Power: Press to turn ON/OFF the device.
  • Color Wheel: Scroll through to find specific colors.
  • Three Choices of White: Press to cycle through the choices of white.
  • Brightness Control: Long press to increase/decrease brightness.
  • Zone Control: Press to select/deselect zones 1-3.
  • Dynamic Modes: The long press adjusts the speed of the dynamic color-changing mode.

Installation Overview

  • Install by NEC and local regulations.
  • Select a suitable location for accessories like DMX decoders, fixtures, etc., ensuring proper wire installation between components.
  • Mount the controller switch box in the wall using a compatible 120-volt shallow Junction Box (Plastic).

Setting the DMX Address

  • Refer to DMX Receiver instructions for setting the DMX address.

Wiring Connections

  • Do not connect directly to 120VAC. Follow the system diagram for correct wiring connections.

Mounting

  1. Use a compatible 120 Volt Shallow Junction Box (Plastic) to wall mount the touch controller.
  2. Pop off the faceplate with a flathead screwdriver for access.

FAQ

Q: Can I use this product with a dimmable power source?

A: No, using a dimmable power source with this product may void the warranty and cause potential hazards.

Q: What wire gauge should be used for the output terminals?

A: Use 24 to 18 AWG gauge wire for the output terminals to ensure proper functionality and safety.

SAFETY & WARNINGS

  • Securely mount the Hueda™ Controller
  • This product is intended to be installed and serviced by a qualified licensed electrician. Install by the National Electric Code and local regulations. Only power with a regulated (listed) constant voltage Class 2 power supply (12-24V DC Max).
  • Failure to use a Class 2 power supply may cause fire or serious injury and will void the limited warranty. Never use this product with a dimmable or magnetic dimmable power source(driver)
  • Ensure the applicable wire is installed between the driver, fixture, and any controls in between. When choosing wire, factor in voltage drop, amperage rating, and type (in-wall rated, Plenum rated, wet location rated, etc.).
  • Inadequate wire installation could overheat wires and cause fire.
  • This product is rated for indoor installation and only for dry locations. Do not install in washrooms or areas near water (or the possibility of in the future).
  • Do not modify this product beyond the instructions in this guide or the limited warranty will be voided.
  • Wiring diagrams in this installation guide for basic installations. Please carefully review your installation before proceeding with a qualified electrician familiar with low-voltage wiring.
  • Never install the HUEDA™ Controller with other high voltage Junction Box as there is a risk of shock hazard! National
  • Electric Code requires electrical conductors to be separated by a barrier within the box or in a separate box! Install only in the provided Junction box.

IMPORTANT NOTE

  • Install the Hueda DMX controller in a separate box rated for Low-voltage use. NEC codes require conductors shall not be placed in any raceway, compartment, outlet box, junction box, or similar fitting with conductors of electric light or power.

WIRE ENDS

WIRE 6-8MM (0.25-0.30″)

  • Exposed wire should not be more than 6- 8 mm long & solder tip (tinned). Do not allow Wires to cross and insure all exposed wire is fully inserted into the screw terminals. Hand-tighten screw terminals. Use 24 to 18 AWG gauge wire for output terminals.

INCLUDED ITEMS IN BOX

  • CAT5 Wire
  • Instructions

REMOTE OPERATION

  • The DMX controller can also be controlled remotely via wi-fi with a compatible(iOS version> 8.0) iOS tablet or mobile device using our application “HUEDA”.
  • Please see our HUEDA™ web page for application instructions.

OPERATION OVERVIEW

INSTALLATION OVERVIEW

  • Install in accordance with the NEC and local regulations.
  • Turn power OFF at the main circuit breaker and verify the power is off.
  • Determine an accessible location for a compatible low-voltage driver to be installed between the main breaker and the DMX controller.
  • Determine a location to install additional accessories such as DMX decoders, fixtures, etc. Ensure the applicable wire is installed between all components.
  • When choosing wire, factor in voltage drop, amp rating, and type to prevent fire or electric shock.
  • Remove the existing wall plate and switch. Pull the switch from identify wires and disconnect from the switch.
  • Remove the existing switch box from the wall and install the included DMX controller switch box. Additional tools may be required to fit the DMX controller switch box in the wall.
  • Make wiring connections. See ‘Wiring Connections’ and ‘Mounting Diagram’ for additional information.
  • Replace the wiring back into the switch box. Mount and align DMX decoders/fixtures. See ‘Setting the DMX Address’.

SETTING THE DMX ADDRESS

  • Please refer to DMX Receiver instructions for setting the DMX address

WIRING CONNECTIONS

  • DO NOT connect directly to 120VAC.
  • See ‘System Diagram for a general system design.

MOUNTING

  • Pop off the faceplate with a flathead screwdriver
  • Use a compatible 120 Volt Shallow Junction Box (Plastic) to wall mount the touch controller.

WARNING!

  • Never install the HUEDA™ Controller with other high voltage Junction Box as there is a risk of shock hazard!
  • National Electric Code requires electrical conductors to be separated by a barrier within the box or in a separate box! Install only in the provided Junction box

PINOUT CONNECTION GUIDE

  • The following diagrams/tables indicate the appropriate connections for patching your own CAT5/RJ45, and XLR-3 splice cables. These diagrams are for general reference and may slightly differ between different cable manufacturers.

RJ45 568B Connection Pinout

RJ45 568B Pinout Table

Pin No. Wire Color Function
1 White/Orange Data +
2 Orange Data –
3 White/Green None
4 Blue None
5 White/Blue None
6 Green None
7 White/Brown May be used as 2nd ground
8 Brown Ground

XLR-3 Connection Pinout

XLR-3 Pinout Table

Pin No. Function
1 Ground
2 Data –
3 Data +

DYNAMIC MODE CHART

  • The Dynamic Mode tool plays factory-programmed scenes.
  • Choose up to 10 different scenes. Short press switches/pauses the mode. The long press adjusts the speed of the dynamic mode.
Mode Description
1 Full Color Fade #1
2 Reverse Rainbow Fade
3 Random Full Color Fade
4 7 Color Jump
5 RGB Fade In / Fade Out
6 RGB Fade Into Off
7 RGB On to Fade Out
8 RGB Jump
9 Full Color Fade #2
10 Pastel Color Fade In / Fade Out

TROUBLESHOOTING

For thorough troubleshooting of LED strip lights and fixtures, see LED fixture installation guides.

LED fixtures not responding to touch

  • Ensure the blue indicator light is on by pressing the ‘Power Button’.
  • Ensure the appropriate zone number is pressed before controlling the DMX decoder/fixture. For example, if you know the fixture is addressed to zone 1, press 1 before controlling.
  • Ensure the individual zone has not been turned off. Pressing zones 1-3 will turn the specific zone ON/OFF. Additionally, long pressing R, G, and B, will increase/decrease individual brightness, and tapping will turn R, G, B, W ON/OFF.
  • Ensure the DMX decoder/fixture is addressed properly. For example, address ‘001’ will respond to zone 1 of the controller.
  • See ‘Setting the DMX Address for additional addressing information.

LED fixture responding incorrectly

  • Ensure all wiring connections are correct. Reversing the Data + and Data – will cause lights to flicker and not respond to the controller.
  • Power connections of all components (drivers, DMX decoders/fixtures, DMX controller).
  • DMX Data connections -see ‘Pinout Connection Guide’ and ‘System Diagram’ for Rj45 hard-wiring connections.
  • DMX decoder PWM output connections -see ‘System Wiring Diagram for CH 1-4 connections

SCAN OR CODE TO DOWNLOAD HUEDA ™ APPLICATION

FCC STATEMENT

FEDERAL COMMUNICATIONS COMMISSION

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interterence received, including interterence that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications will void the user’s authority to operate the equipment and warranty.

SYSTEM WIRING DIAGRAM

The following wiring diagram is an example of system connectivity. CAT5 (RJ45 connections) cables are the most effective solution for transmitting DMX-512 signals. XLR-3 cables may also be installed but require an additional adapter for connecting to DMX decoders. With DMX decoders it is possible to transmit signal wireless with the use of LC-51 2X wireless sticks. Always review each component’s installation guide for detailed and up-to-date wiring instructions.
Install in accordance with NEC and local regulations.

LT-995 DMX Decoder

HUEDA APP WIFI CONNECTIVITY INSTRUCTIONS

  1. Step 1: Turn on the HUEDA™ Master Controller. A blue light in the middle of the color circle indicates that the HUEDA™* controller is turned on.
  2. Step 2: On your iOS device go to wifi settings. From the available wifi networks look for Easy Lighting or Hueda. Select Easy Lighting or Hueda as the wifi network. Enter the password 0123456789.
  3. Step 3: Open the HUEDA” App on your iOS device. Use Color Circle on the app to change the color to make sure that the HUEDA™™ app is connected to HUEDA’™’s Master Controller device wifi. It will not change the color of the HUEDA™™ app is not connected to Mater Controller wifi. Follow the above steps to make sure that the app is connected to Mater Controller wifi.
  4. Step 4: To connect to the Home Wifi network while changing color with the HUEDA’™ app, go to the settings tab on HUEDA”™. Select the Master Controller MAC address.
    • It will bring you to the network settings page. From the available settings select the Connect to Home Network and follow the instructions to connect to the Home wifi network.
  • LED World Inc. #130 10615 48 ST SE  CALGARY, AB T2C 2B7  CANADA  Version 4.3 03/06/24
  • Copyright © 2024 LED WORLD INC™. All Rights Reserved.
  • We are not responsible for errors or omissions.
  • Product and specifications are subject to change without notice.
  • Registered trademarks are owned by their respective registers, or licensee(s).
  • ledworldlighting.com
  • ledworld.ca
  • 1-800-387-4081

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals