LED WORLD LIGHTING LS2 RGB-W LED Receiver User Manual

June 9, 2024
LED WORLD LIGHTING

LED WORLD LIGHTING LS2 RGB-W LED Receiver User Manual

LED WORLD LIGHTING LS2 RGB-W LED Receiver User Manual

BEFORE YOU BEGIN, READ ALL WARNINGS AND INSTALLATION INSTRUCTIONS (AS THEY MAY HAVE BEEN UPDATED FROM PREVIOUS VERSIONS ).
IMPROPER INSTALLATION(S) PRESENT HAZARDS, WHICH CAN RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE.

SAFETY & WARNINGS

Securely mount the LS2 using the two mounting points at each end.

This product is intended to be installed and serviced by a qualified licensed electrician. Install in accordance with the National Electric Code, and local regulations.
Only power with a regulated (listed) constant voltage Class 2 power supply (12-24V DC).

Ensure applicable wire is installed between driver, fixture, and any controls in between. When choosing wire, factor in voltage drop, amperage rating and type (in-wall rated, wet location rated, etc.). Inadequate wire installation could overheat wires and cause fire.

This product is rated for indoor installation and only for dry locations. Do not install in washrooms or areas near water (or the possibility of in the future).

Do not modify this product beyond the instructions in this guide or the warranty will be voided.
Wiring diagrams in this installation guide for basic installations. Please carefully review your installation before proceeding with a qualified electrician familiar with low voltage wiring techniques.

INTRODUCTION

5 in 1 (RGB, RGBW, CCT, RGB+CCT and single color) controller is the wireless controller works with wireless remote FUT089. The LS2 controller features mesh network and auto-synchronizing function with brightness, CCT, RGB, RGBW and RGB+CCT output mode. LS2 controller uses 2.4GHz wireless technology. It consumes less power, transmits signal over a long distance and it is anti- interference.

LS2 OPERATION OVERVIEW

LED WORLD LIGHTING LS2 RGB-W LED Receiver - LS2 OPERATION
OVERVIEW

LS2 TECHNICAL SPECIFICATIONS

LED WORLD LIGHTING LS2 RGB-W LED Receiver - LS2 TECHNICAL
SPECIFICATIONS

MESH NETWORK

LED WORLD LIGHTING LS2 RGB-W LED Receiver - MESH
NETWORK

Controllers can send signals to another controller within 75ft (22.8m) distance creating a mesh network.

WIRING DIAGRAM

Warning: Input voltage must be identical to output voltage of the LED Fixture!

WIRE 6-8MM (0.25-0.30”)

Exposed wire should not be more than 6- 8 mm long & solder tip (tinned). Do not allow Wires to cross and insure all exposed wire is fully inserted into the screw terminals. Hand tighten screw terminals. Use 22 to 16 AWG gauge wire for output terminals.

LED WORLD LIGHTING LS2 RGB-W LED Receiver - Diagram-1

LED WORLD LIGHTING LS2 RGB-W LED Receiver - Diagram-2

RGB FIXTURE WIRING DIAGRAM

LED WORLD LIGHTING LS2 RGB-W LED Receiver - RGB FIXTURE WIRING
DIAGRAM

RGBW FIXTURE WIRING DIAGRAM

LED WORLD LIGHTING LS2 RGB-W LED Receiver - RGBW FIXTURE WIRING
DIAGRAM

SINGLE COLOR FIXTURE WIRING DIAGRAM

LED WORLD LIGHTING LS2 RGB-W LED Receiver - SINGLE COLOR FIXTURE WIRING
DIAGRAM

CCT ADJUSTABLE FIXTURE WIRING DIAGRAM

LED WORLD LIGHTING LS2 RGB-W LED Receiver - CCT ADJUSTABLE FIXTURE WIRING
DIAGRAM

RGB+CCT FIXTURE WIRING DIAGRAM

LED WORLD LIGHTING LS2 RGB-W LED Receiver - RGB+CCT FIXTURE WIRING
DIAGRAM

PAIRING/UNPAIRING WITH FUT089 REMOTE CONTROLLER

Pairing:

  • Turn OFF LS2 receiver by disconnecting the power, then turn ON by reconnecting the power after about 5 seconds.
  • Before pressing anything on the FUT089 remote controller, press “I” button on the desired zone 3 times quickly. Connected LED fixture light will blink 3 times when the pairing is done.
  • Check the indicator light on LS2 receiver according to connected LED fixture. (eg. For RGB mode indicator light should be red). Touch the color
    wheel to make sure that device is paired and changes the color.

Note: If you have to control multiple receivers synchronously, each receiver should be paired according to the above steps.

Unpairing:

  • Turn OFF LS2 receiver by disconnecting the power, then turn ON by reconnecting the power after about 5 seconds.
  • Before pressing anything on the FUT089 remote controller, press “I” button on desired zone you wish to unpair 5 times quickly. Connected LED
    fixture light will blink 10 times when the receiver is unpaired.

Note: Changing a receiver to a different zone can be done using the above steps. Unpair it first from current zone, then pair it to new zone number.

LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 2.1 09/29
Copyright © 2022 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specifications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals