AENO GS2 Garment Steamer User Manual

AENO GS2 Garment Steamer

Technical Specifications

• Supply voltage: 220–240 V~;
• Frequency: 50/60 Hz.
• Power: 1000.0–1190.0 W.
• Dimensions (L x W x H): 96 mm × 95 mm × 408 mm.
• Water tank capacity: 0,105 l.
• Steam supply: 24 g/min.
• Steam temperature: up to +150 °C.
• Steam pressure: 0.4 bar.
• Continuous operation time: 7–12 min.
• Operating conditions:
  • temperature -20–70 °C,
  • humidity 0–93 %.

Scope of supply (figure A)

AENO steamer (1), measuring cup (3), glove (4), case (5), quick start guide, warranty card.

Limitations and Warnings

WARNING! The unit connected to the mains is live even after it has been switched off via the power button (6) (figure B). Unplug it immediately after
use, before cleaning, filling and emptying the water tank. Do not allow the device to come into contact with water. Never leave the appliance unattended while it is plugged in. Do not allow children to use or play with the device. Do not operate a damaged steamer. Use the device indoors only. Unplug the unit using the power plug, not the cord. Do not use an extension cord. Use only drinking water, preferably distilled water. Do not switch on the device with an empty tank. Do not add vinegar, detergents, chemicals or fragrances to the water. The steaming head gets hot during operation, do not touch it. Do not point the steaming head against people. Never steam clothes on a person. Check care label before steaming. To avoid burns, wear a glove (4) on the hand holding the garment while steaming.

Before you begin

Unpack the device. Do not plug the unit in until you have filled the water tank (2) according to figure C.

Operation (figure D)

Connect the device to the mains by inserting the power plug into the power outlet. Move the switch (7) to the “ON” position. The button indicator (6) will light up and flash. Wait about 40 seconds for the steam to build up. Quiet crackling during heating is allowed. The device is ready for operation when the button indicator (6) lights steadily. Place the item to be steamed vertically or horizontally. Point the nozzle away from yourself and those present, press the steam button (6). Let out the first portion of steam on an inconspicuous area of the product, as a few drops of water may come out. Then point the nozzle at the surface to be steamed. When finished, press the steam button (6) again. Turn the switch (7) to the OFF position to turn the unit off. Unplug the unit and drain the remaining water from the water tank.

WARNING! When using it for the first time, check the operation of the device on old clothing: it is possible that dust accumulated in the device during transport and production may get in.
Note: For more efficient steaming in an upright position, it is recommended to pull the garment lightly with your free hand and glove on (4) and slowly move the steamer from top to bottom. When steaming horizontally, it is recommended to move the steamer forward and backward.

Maintenance and cleaning

To clean the steamer wipe with a soft damp cloth. Do not use any detergents or cleaning agents. Do not attempt to use any descaling agent, this will damage the device. If you are in very hard water area, use distilled or bottled water.

Troubleshooting possible malfunctions

• The device does not heat up. Possible reason: the device is not switched on or not connected to the power supply. Solution: Make sure the unit is turned on, the power plug is connected to the outlet, and the outlet is in good condition.
• The device does not generate steam. Possible causes: low water level in the tank; the unit is not turned on or not connected to the mains. Solution: unplug the unit and fill the reservoir with water; make sure the unit is turned on, the plug is plugged into the outlet, and the outlet is in good condition.
• Water drips from the steaming head or leaks out of the tank. Possible causes: device is not heated to the desired temperature; water tank lid (2) is not properly closed. Solution: wait until the button indicator (6) lights up continuously (about 40 seconds); close the water tank lid (2) according to the instructions in figure C.

WARNING! If none of the possible solutions solves your problem, contact your supplier or service center. Do not disassemble or attempt to repair the unit yourself.

Recycling information

These symbols indicate that you must follow the Waste Electrical and Electronic Equipment (WEEE) and Waste Battery and Battery Regulations when disposing of the device, its batteries and accumulators, and its electrical and electronic accessories. According to the rules, this equipment must be disposed of separately at the end of its service life. Do not dispose of the device, its batteries and accumulators, or its electrical and electronic accessories together with unsorted municipal waste, as this will harm the environment. To dispose of this equipment, it must be returned to the point of sale or turned in to a local recycling facility.
You should contact your local household waste disposal service for details.
ASBISc reserves the right to modify the device and to make edits and changes to this document without prior notice to users.
The warranty period and service life shall be 2 years as from the date of purchase of the device. Manufacturer: ASBISc Enterprises PLC, Lapetou, 1, Agios Athanasios, 4101 Limassol, Cyprus. Made in China. For current information and details on the device description and specification, as well as connection process, certificates, warranty, and quality issues, see relevant Installation and
Operation Manuals available for downloading at aeno.com/documents. All trademarks and names herein are the property of their respective owners.

www.aeno.com/documents

aeno.com

References

• Documents | AENO in Europe
• Documents | AENO in Europe

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>