GIPS GT-130 UWB Tag User Guide

: June 4, 2024
: GIPS

Table of Contents

INTRODUCTION
PRODUCT SPECIFICATION
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

GT-130 Reference Guide

INTRODUCTION

1.1 Main Features

Meet IEEE 802.15.4a UWB
BLE 5.0
SOS Button
Vibration, Buzz Alert
IP66
RFID (ISO14443A)
ToF/TDoA Mode Supported
Smart Rest Mode

1.2 Description
GT-130 is the UWB tag used in GIPS Real Time Location System (RTLS) solution, which supports the TOF / TDOA positioning algorithm. GIPS RTLS solution can be applied in hospitals, factories, warehouses, and other fields.
The typical deployment structure is shown as below figure, GT-130 is attached to the monitored item such as staff, equipment, etc. UWB tag emits the signal to the UWB anchors on the field side and can be positioned on the server. GT-210 could be configured or issued by the software on the server side through the UWB anchor.

1.3 Product outline
1.3.1 Product Pictures

1.3.2. Product outline

PRODUCT SPECIFICATION

General

3 months, at 1Hz, TDoA mode with smart rest
Power Dissipation| < 1W (Instant)
Indicator Light| • Three Color LED:
Red Flicker: Low Power Status / SOS alert
Green Flicker: Flash while uwb is working
Blue Flicker: Charging Status / BLE connecting mode
Blue Light: Charging Full
Temperature| • Charging: 0°C~45°C
• Operating: -20°C~60°C• Storage: -10°C~55°C
Humidity| • Operating: 0%~90% without condensation
• Storage: 0%~90% without condensation
UWB
Working Frequency| 3.25GHz~6.75GHz (Channel 2/3/5)
Physical Rate| 110 Kbps / 850 Kbps / 6.8 Mbps (Adjustable)
Output power (25ºC)| -41.3dBm/MHz
Channel Bandwidth| 500 MHz
Antenna Specification| Chip antenna, peak gain 5dbi (average)
Working Mode| ToF / TDoA
BLE
Protocols| Bluetooth v5.0 BR/EDR and BLE specification
Radio| 2.4 GHz Nordic’s proprietary 1 Mbps and 2 Mbps mode
Antenna Specification| Chip antenna, peak gain 3.77dbi (typical)
Output power (25ºC)| +2 dBm
Receiving sensitivity| -96 dBm
Others
Message Upload| SOS alert
Low battery alert
Smart rest
Alarm Issuance| Vibration
Buzzer
Red Flash
Configuration Tools| GIPS_Tag_Monitor_v1.0.0(Android APP)

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example – use only shielded interface cables when connecting to computer or peripheral devices).
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0.5 centimeters between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at least 0.5 cm from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter.
UWB systems operating under the provisions of this section shall bear the following or similar statement in a conspicuous location on the device or in the instruction manual supplied with the device: “This equipment may only be operated indoors.
Operation outdoors is in violation of 47 U.S.C. 301 and could subject the operator to serious legal penalties.”
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

GIPS Technology Co., LTD.