WOLFBOX V05 Level 2 EV Charger User Manual

WOLFBOX V05 Level 2 EV Charger User Manual

INSTALLATION INSTRUCTION

Preface

Thank you for purchasing WOLFBOX products. Our equipment is manufactured to high standards and will provide 3 years of trouble-free performance if used in accordance with these instructions andproperly maintained.

IMPORTANT

• Before operating or maintaining this equipment, please read this manual carefully and follow the instructions for installation and operation, paying special attention to safety warnings and precautions. Improper use of this product may result in product damage and personal injury and void the product warranty.
• Under no circumstances does compliance with the information in the instructions relieve the user of the responsibility to comply with all applicable codes and safety standards. This document describes the install process. If you are unable to perform the steps described below, please contact us. We are not responsible for any damages resulting from custom installations or procedures not described in this document or from failure to comply with the recommendations.

Safety Instructions

The safety messages herein cover situations WOLFBOX is aware of. WOLFBOX cannot know, evaluate or advise you as to all of the possible hazards. You must be certain that any condition or service procedure encountered does not jeopardize your personal safety.

WARNING

• This equipment should be installed by a licensed electrician only in accordance with all local codes and ordinances.
• This equipment must be grounded through the permanent wiring system or equipment grounding conductor, otherwise it may result in the risk of electric shock or fire.
• Children should be supervised when using this equipment.
• Do not insert fingers or foreign objects into the EV connector.
• Do not install or use this equipment near flammable materials, explosive, irritating or combustible substances, chemicals or vapors.
• Do not use this product if the flexible power cord or EV cable is frayed, has broken insulation, or any other signs of damage.
• Do not use this product if the enclosure or the EV connector is broken, cracked, open, or shows any other indication of damage.
• Use only 90° copper wire conductors.
• Do not operate this equipment outside operating temperature range of -30℃~50℃(-22℉~122℉).
• Please install this equipment correctly. Improper installation and testing of the equipment may result in property damage, personal injury.
• Handle the equipment carefully during transportation. Do not use force, shock or pull, twist, wrap, drag or step on the equipment to avoid damage to the equipment or equipment parts.
• For NEMA plug-in versions, use only NEMA outlets (14-50). For your own safety, do not unplug the charger during charging.
• THE SUITABILITY OF THE USE OF FLEXIBLE CORD IN ACCORDANCE WITH CE CODE, PART I.

For use with electric vehicles.
Ventilation Not Required.

CAUTION

To avoid the risk of fire or electric shock, do not use this equipment is used with extension cord.

GENERAL INTRODUCTION

Packing List

Other tools you may use and need to prepare for yourself :

1. Socket of NEMA 14-50 or power supply for installing Hardwired circuitry
2. Drill
3. Pen
4. Hammer
5. Screwdriver

CAUTION

• Connector holder and installation accessories only apply to the product model provided with this product.
• The list above does not necessarily include all tools required for installation. We recommend that you read through the installation process and gather the tools you need before installing.

Product Overview

1. Indicator Light
2. Display Screen
3. RFID Reader
4. Current Inlet Cable
5. Charging Cable (Cable Length 25ft)
6. Product Labels
7. Amperage Labels

Indicator light Description

Overall Drawing

NEMA Plug-in Version (E40)

Hardwired Version (E50)

INSTALLATION GUIDE(REFERENCE)

IMPORTANT

Please follow all applicable codes and regulations and obtain permits to complete electrical work as required.

Location

1. Mount the unit on a vertical surface that will support its weight (e.g., a finished wall). The maximum weight of this product is approx 10.5kg .
2. Keep this equipment installed in allowing wire bending tolerance within the scope of the position.
3. Place the charger in a position that is not easily damaged.

Positioning

1. A 50A or higher current fuse is recommended for installation circuits of the E40 model.
A 70A or higher current fuse is recommended for installation circuits of the E50 model.

IMPORTANT

In Canada, a NEMA plug-in installation is only allowed with a 50 amp circuit.

Higher amperage connections are also available for this product. See all applicable codes for circuit breaker and wire sizing requirements. Field terminals are rated to 105°C and accept up to 6 AWG (16 mm²) wire.

Circuit Rating| Max Load| Estimated Range per Hour| Plug- In| Hardwire
---|---|---|---|---
80 A| 50 A| 45miles/72km| no| yes
70 A| 50 A| 45miles/72km| no| yes
60 A| 48 A| 44miles/70km| no| yes
50A| 40A| 37miles/60km| yes| no

1. For NEMA plug-in installations, determine the type of plug purchased, NEMA 14-50 plug.

2. Ensure that the electrical panel supports 240V dedicated circuits and new dedicated non-GFCI bipolar disconnects in accordance with local regulations.

3. The recommended installation height is between 1100mm(43inch) and 1500mm(59inch). For NEMA plug-in installations, the NEMA should be at least 460mm (18inch) off the ground adjacent to the charger mounting location, but make sure both are positioned within the adjustable range of the wire. Within the adjustable range of the cord.

CAUTION

• The suitability of the use of flexible cord in accordance with CE code, part I, rule 4-012, is to be determined by the local inspection authority having jurisdiction.
• The input power cable length is 300mm (12 inches) (According to the National Electric Vehicle Charger Electrical Code).
  

Current Line Description

Ground Requirements

• The charger must be connected to the earthing metal permanent wiring system. Equipment grounding conductor must be run with circuit conductor, and connect to the equipment grounding terminal or lead on the charger.
• The grounding conductor shall be grounded to earth at the service equipment or, when supplied by a separately derived system, at the supply transformer.
• Ensure that a grounding conductor that complies with all applicable codes is properly grounded to earth at the service equipment, when supplied by a separate system, at the supply transformer.
• Neutral is not used to power the charger but must be properly connected to ground, at the panel transformer, to provide necessary voltage reference relative to ground.

DANGER: RISK OF SHOCK.

Disconnect the 240V power vac. Do not turn on the power until you are sure the installation is complete. Failure to following this instruction may result in electric shock or electrocution.

Hardwired Installation

For this version installation,please follow all applicable codes and regulations and obtain permits to complete electrical work as required.

NEMA Plug-in Installation

WARNING

To avoid the risk of fire or electric shock, do not use this product with an extension cord.

1. Find the ideal installation location for the device. Note: The installation position should ensure that the NEMA cable is properly bent and cannot be over-stretched.
   

2. To use the wall mount bracket, first confirm the top two holes on the wall, corresponding to points A and B. Then drill holes in points A and B, and place M10 expansion bolts and M6*50mm screws. Note: About 5mm length of M6 screws should be reserved for placing the device.

3. Place the bracket on the screws at points A and B to confirm and mark the position of point C. Then drill a hole at point C and put in the expansion bolt.

4. Use M4*6mm screws to fix the bracket on the back of the Electric Vehicle Supply Equipment.

5. When the EVSE and bracket are combined, place them on screws A and B. And use M4*40mm screwBthrough point C to fix the device on the wall.
   

6. . Install the EV connector bracket in place using M6 expansion bolts and M4*40mm screws. Note: The connector Holder should be located within the flexible range of the cable.

INSTRUCTIONS FOR USE

Charging Steps

Note : Ensure that the equipment is properly connected to the power supply.

1. Insert the connector into the vehicle power port

2. Start charging by swipe RFID card or use the App.
   CAUTION
   Do not disconnect the connector during charging. Otherwise, there is a risk of damage to the connector or Electric Vehicle Supply Equipment

3.  End of charging by swipe RFID card or use the App.
   

4. Unplug the connector and put it back in place

About Management Card

When the EV charger cannot connect to the App, you’re going to need this card.

Usage Method:
Swipe the management card in the RFID reader area and the EV charger will prompt “Reset action in progress”;After 10 seconds, EV charger will prompt “Confirm reset”.At this point, swipe the management card again. When the EV charger prompts “reset complete”, it means that the Wi-Fi function of the EV charger has been reset.

NOTE: If the fault persists, please contact us.

Fault Description

Note: When the red light flashes, it indicates a malfunction.

this fault
E2| Under-voltage alarm| Consult your local electric service to confirm that the voltage in this area is stable. If it is below 175V, this error will Appear

E3

|

Over-voltage alarm

| 1. If the voltage exceeds 265Vac for a short time, wait for the grid to return to the normal voltage range by itself
2. Consult your local electric service to confirm that the voltage in this area is stable. If it is higher than 265V, this error will Appear

E4

|

Ground fault

| 1. Immediately disconnect the power distribution box
2. Check whether the equipment input/output line grounding is normal, and whether the input L/N is connected in the normal order
3. Exclude the above problems, re-energize

E5

|

Over current protection

| 1. Immediately disconnect the power distribution box
2. Check whether there is low impedance or short circuit between the two lines of the output line of the device
3. Exclude the above problems, re-energize

E6

|

Permanent overcurrent protection

| 1. Immediately disconnect the power distribution box
2. Check whether there is low impedance or short circuit between the two lines of the output line of the device
3. Exclude the above problems, re-energize

E7

|

Leakage protection

| 1. Immediately disconnect the power distribution box
2. Check if the device output line is broken or has low impedance or short circuit to ground
3. Exclude the above problems, re-energize
E8| Over temperature protection| Check the environment in which the equipment is installed,verify that there is no other heat generating equipment next to it, and ensure that the ambient temperature is below 45°C (113°F)
E9| RFID failure| Contact the after-sales service team for this fault
E10| Relay failure| Contact the after-sales service team for this fault

E11

|

Memory failure

| 1. Confirm that the battery of the electric vehicle is fully charged
2. The charging settings of the EV and the EV Charger do not match. You need to change the charging settings on the vehicle side
3. The EV fails to receive the current from the charging post in time. You need to plug and unplug the EV Connector again.
E12| Clock exception| Contact the after-sales service team for this fault
| | |

• If you have any q| uestions, please contact the after-sales team.|

WOLFBOX EV APP

App Download

1. Scan the QR code below to download the “WOLFBOX EV” App to your mobile device. For IOS users, you will be redirected to the App Store; For Android users, you will be redirected to the Google

Play.App Download

App Use

2. After downloading, open the “WOLFBOX EV” and register

Sign Up and Log In

Sign Up:HUI

Step 1 : Open the “WOLFBOX EV” App and select “Sign Up”.

Step 2 : Enter your cell phone number or email to get the verification code.

Step 3 : Confirm you receive a verification code from “WOLFBOX EV” and fill it out.

Step 4: Set up your login password.

Log In:

Step 1 : Open the “WOLFBOX EV” App and select “Log In”.

Step 2 : Read and check the relevant agreements, then enter your account number and password to log in.

App Connection

Note: If App can’t connect the EV charger. Please use the management card

Use of management card
Swipe the management card in the RFID reader area and the EV charger will prompt
“Reset action in progress”;After 10 seconds, EV charger will prompt “Confirm reset”.
At this point, swipe the management card again. When the EV charger prompts “reset complete”, it means that the Wi-Fi function of the EV charger has been reset.

Preparation Before Connection

1. Preparations For EV charger:Ensure that the Wi-Fi signal in the environment is 2.4GHz.Make sure the Bluetooth module is not in a dormant state (if no connection is made within 3 minutes after the EV Charger is powered on, the Bluetooth module will go into a low power mode and will need to be repowered to wake up the Bluetooth module).

Tips: For environments with poor or no network:

1. If the environment of the network is poor, you can try to open a hot spot, with a hot spot connected to the app can be realized to control the charging station, but some of the functions may not be able to enjoy.
2. If the App has been connected, you can realize the app control pile through Bluetooth. But the charging record and some functions can’t be enjoyed.
3. If there is no network in the environment, there is no way to connect the app, you can only swipe the charging card to realize.

Preparations For Mobile Device:

Ensure that the mobile device is in a network-connected environment.

Step 1: Click “Add Device” on the main page or “+” in the upper right corner to add a device.

Step 2: On the “Add Device” page, follow the prompts to confirm that “Wi- Fi” and “Bluetooth” are turned on. Including Application permissions and cell phone system Bluetooth.

Add Devices

Automatically Add Device

Step 1 : Click “Add Device” on the “Home” page or “+” in the upper right corner and then jump to the page of “Add Devices”.

Step 2 : Click “Add” and select the device “WOLFBOX EV charger”.

Step 3: Confirm the Wi-Fi information and connect.

Step 4: After successfully connecting, click “Done” and jump to “Charge” page.

Add the Device Manually

Step 1 : In the “Add Device” interface, pull down and find “Energy”, select “EV charger (BLE)”.

Step 2 : Ensure that the EV charger is in a network-connected environment. (When the charging equipment is connected to the internet, a light in pale blue color will remain illuminated.)

Step 3 : Confirm the Wi-Fi information and connect.

Step 4: After successfully connecting, click “Done” and jump to “Charge” page

App Function

Charge Page (Idle State)

1. Information: Device information, share device, FAQ and feedback, remove device, etc.
2. Charging Current: Select the output current level of EV charger. (Note: Choose the “Auto” option, and the current will automatically set to the highest acceptable level for the vehicle, but the output current level will not surpass the device’s maximum current level.)
3. Plug and Charge Mode: After enabling this mode, the EV charger can directly  charge the vehicle without requiring an unlock, which may pose certain security risks to your product. Please confirm.
4. Scheduled Charging: Set the start and end times for scheduled charging.
5. Reminder of booking charging mode and Set the start time and end time for scheduled charging.
6. Connector prompt, Sliding charge indicator, Charge mode indication.
   

Important Note:
You cannot activate both the ‘Plug & Charge’ mode and the ‘Scheduled Charging’ mode simultaneously. You can select the charging mode that best suits your needs

Charge Page (Charging Status) & Charge Settlement

1. Current Charging Duration.
2. Current charging power.
3. Current Charging Data: Voltage, Current, and Temperature of the EV charger.
4. Increased data: power and mileage (for reference only).
5. End charging.
6. The mileage increased of this charge (for reference only).
7. The duration of this charge.
8. The increased power of this charge (for reference only).
9. The electricity charge used for this charging (for reference only).

**Schedule Charging

**

1. Schedule charging start and end time.
2. Set charging current size (Defaults to AUTO).
3. Set charging date (Monday to Sunday).
4. Enable Push Notification Before Charging Starts.
5. Save or cancel the relevant settings for
6. scheduled charging

**Data

**

1. Electric: Select to view the amount of power consumed by charging (for reference only).
2. Cost: Select to view the amount of money consumed by charging (for reference only).
3. Select Time: Select the start time and end time to check the data within the time period.

**Set

**

1. Temperature Unit: Select units in ℃ or ℉
2. Cost Unit: Currency type setting
3. Vehicle Information: Whether to display vehicle  information
4. Range unit setting: Select units in km or Miles
5. Indicator Light Switch: Turn on or turn off the EV charger lights

Other Setting

Share Device

Step 1: Click the ” ” in the upper right corner of the “Set” page.

Step 2 : Click “Share Device” to enter “Add Sharing” page.

Step 3: Click “Add” to share the device by entering the other user’s WOLFBOX EV account or by other means (SMS, email, copy link, etc.).

1. Note: The maximum number of user shares is 19.
2. Shared users also need to download “WOLFBOX EV”.

Setting Shared User Privileges (Remove Sharing & Privilege Duration) 

Step 1: Follow the steps in “Sharing Device” to enter the “Add Sharing” page and click the ” ” in the upper right corner.

Step 2: Enter to view the users who have been shared.

Step 3: Select the user you want to change the privilege to cancel the sharing and the privilege duration

Remove the Device

Step 1 : Enter the “Set” page and click ” ” in the upper right corner.

Step2: Disconnect: Disconnect from EV charger. Disconnect and wipe data: The device will be restored to factory Settings and removed from the device list.

FTER-SALES INFORMATION

IMPORTANT

You are responsible for the proper installation and maintenance of the Electric Vehicle Supply Equipment.

Out of Scope Warranty

1. Improper site preparation or maintenance, improper installation, cosmetic  damage such as scratches and dents, or normal deterioration.
2. Abuse, vandalism, damage or other problems caused by accident, misuse or negligence (including, but not limited to, physical damage caused by vehicle impact), or use of the Electric Vehicle Supply Equipment in a manner other than that specified in the Applicable WOLFBOX documentation.
3. Damage to the Electric Vehicle Supply Equipment caused by software, interfaces, components, supplies or any other products not supplied by WOLFBOX.
4. Damage caused by failure to install, alter, disassemble, modify or relocate Electric Vehicle Supply Equipment in accordance with the installation guidelines.
5. Damage caused by extreme electrical surges, extreme electromagnetic fields, or other causes beyond control.

In addition: The Electric Vehicle Supply Equipment warranty will not Apply ifs the original identification markings of your Electric Vehicle Supply Equipment (e.g., serial number and logo) are damaged, altered or removed.

WOLFBOX shall not be liable for any direct, indirect, incidental, special, punitive or consequential damages, including, arising out of or in connection with your purchase or use of a Electric Vehicle Supply Equipment or inability to use Electric Vehicle Supply Equipment, under any theory of liability, whether in an action in contract, strict liability, tort (including negligence including negligence) or other legal or equitable theory, even if WOLFBOX knew or should have known of the possibility of such damages. in no event will WOLFBOX’s cumulative liability for all claims relating to the Electric Vehicle Supply Equipment exceed the price you paid for the Electric Vehicle Supply Equipment. The limitations set forth herein are intended to limit WOLFBOX’s liability and shall Apply to any failure of the essential purpose of the limited remedy.

Promise

We are committed to giving customers the best product experience and after- sale service.

WOLFBOX warrants your Electric Vehicle Supply Equipment to be free from defects in material or workmanship when used under normal operating conditions for a period of three (3) years from the date of original purchase (warranty period). If, during the warranty period, your Electric Vehicle Supply Equipment becomes defective due to a breach of warranty, WOLFBOX will repair or replace the Electric Vehicle Supply Equipment at its option during the warranty period.

NOTE: If you encounter a problem that cannot be handled, you can contact our after-service personnel or customer service staff for help

Brand Contact Details

WOLFBOX
Tel: +1 888 296 8399
Email: EV@wolfbox.com
Business time : 6AM-12AM,1PM-8PM EST(GMT-4) The final interpretation right belongs to WOLFBOX

References

• WOLFBOX® Official Site| Best Mirror Dashcam with 18-month Warranty

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>