ADEPT T6100 Thermostat Instruction Manual

: June 6, 2024
: ADEPT

Table of Contents

Thermostat Instruction
INTRODUCTION
TECHNICAL SPECIFICATIONS
INSTALLATION
THERMOSTAT SYMBOLS
FUNCTION AND OPERATION
TROUBLESHOOTING
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

ADEPT T6100 Thermostat 2 ADEPT T6100
Thermostat

ADEPT T6100 Thermostat - Thermostat

Thermostat Instruction

Easy touch Easy warm

INTRODUCTION

The T6100 series is an intuitive programmable thermostat used to control electrical ﬂoor heating systems or water heating systems. It will keep the home at a comfortable temp whilst minimizing energy use. Install the app on your smartphone to control the heating system remotely with the WiFi thermostat.

TECHNICAL SPECIFICATIONS

Supply voltage: 85-265Vac 50/60Hz
Standby power: ＜1W
Max load: 16A(electric heateng)/3A(water heateng)
IP class: IP21
Cable speciﬁcateon: ≤2.5mm²

INSTALLATION

ADEPT T6100 Thermostat - fig WIRING INSTRUCTION ADEPT T6100 Thermostat - WIRING

THERMOSTAT SYMBOLS

ADEPT T6100 Thermostat - THERMOSTAT
SYMBOLS WIFI CONNECTION

Step 1: Scan the QR code or download the Warmme from the APP store/Google browser.
ADEPT T6100 Thermostat - APP store Step 2: Register and log in with your mobile number/ email address in the APP. Attention: Please read and agree “Privacy Policy and Service agreement” before registrateon

Step 3: Click “Create a family” to enter family information and click “Done”. Attention: Please authorize locateon permissions when creating a family. ADEPT T6100 Thermostat - APP store2

Step 4: Click “Add Device” or “+” on the top-right to add a device. ADEPT
T6100 Thermostat - APP store3

Step 5: Click “Wiﬁ thermostat”, and follow the steps to operate the thermostat, when the WIFI icon ﬂash quickly, please click “Press to connect”. ADEPT T6100 Thermostat - APP store4 Step 6: Enter Wiﬁ password, and click “Conﬁrm”. ADEPT T6100 Thermostat - APP
store5

Step 7: If the device is added successfully, you can change the device name and set the region, then, click “Done”.Attention: If failed, please conﬁrm the Wiﬁ is 2.4G version and check the Wiﬁ signals, then, use the “AP mode” in the top right to connect again. ADEPT T6100 Thermostat - APP
store6

Step 8: You can check the real-time temperature onset temperature etc. at the control interface.

FUNCTION AND OPERATION

7.1 On/Oﬀ
Press to turn On/Oﬀ.
Note: When frost protection is active, the thermostat will maintain the frost protection temp when it is Oﬀ.
7.2 Temporary Override Temperature
The temporary override temp is only valid at the current event and it will not be saved. On the actual temp interface, press to set temporary override temp.
Press to conﬁrm and back to the actual temp interface.
7.3 Key-Lock
Lock all keys to prevent the settings from being changed. On the actual temp interface, press and hold for 3 seconds to lock or unlock all the keys.
7.4 Set the Time
On the actual temp interface, press then the will ﬂash.
Press to enter day seteng.
Press to set day.
Press to enter hour seteng.
Press to set hour.
Press to enter minute seteng.
Press to set the minute.
Press to conﬁrm and back to the day seteng interface.
Press twice to back to the actual temp interface.

If the thermostat is WiFi version, it will update teme automatically after connecting to WiFi.
7.5 Holiday Mode
In Holiday Mode, the thermostat will maintain the set temp until the holiday teme ends.
On the actual temp interface, press then the will ﬂash.
Press to select.HOLIDAY
Press to enter holiday days seteng.
Press to set holiday days.
Press to enter temp seteng.
Press to set temp.
Press to conﬁrm and back to the actual temp interface.
Set the holiday days to zero or double press cancel Holiday Mode.
7.6 Hold Mode
In Hold Mode, The thermostat will hold the set temp until you cancel this mode.
On the actual temp interface, press then the will ﬂash.
Press to select.HOLD
Press to enter the Hold ON/OFF setting.
Press to set Hold ON.
Press to enter temp settng.
Press to set temp.
Press to conﬁrm and back to the actual temp interface.
Set hold OFF or double press to cancel Hold Mode.
7.7 Edit Setting
Edit Seteng can set and change the parameters. If you don’t choose Holiday Mode or Hold Mode.
The thermostat runs according to the parameters of Edit.
On the actual temp interface, press then the will ﬂash.
Press to select.EDIT
Press to enter day selection of Edit Setting.
Press to select a day.
Press to enter the event selection of the day.
Press to select an event.
Press to select the event’s starting time.
Press to set the hour of starting time.
Press to enter the minute setting.
Press to set the minute of starting time.
Press to enter the temp setting.
Press to set the temp.
Press to conﬁrm and back to the event selecton of the day.
Press some times or double press to back to the actual temp interface.
Default parameters

Day	Wake	Leave	Back	Sleep
Mon-Fri	7:00	22.0°C	8:30	19.0°C
Sat/Sun	8:00	22.0°C	8:30	22.0°C

7.8 Advanced Setting
The thermostat provides advanced settings to suit various special situations. These are normally set by technicians during initial installation.
On the actual temp interface, press then the will ﬂash.
Press to select.SETUP
Press to enter advanced settings.
Each set can be accessed by pressing and parameters adjusted by pressing .

No.	Name	Default	Ranges
1	Room temp calibrate	0.0°C	-5.0°C — 5.0°C
2		0.0°C	-5.0°C — 5.0°C
3	ii. visit Wild-ion	ON	OF(OFF) ON
4	knit-frozen ten	5.0°C	5.0°C — 15.0°C
5	Sensor selection	01: Floor sensor	00: Room sensor

1:Floor sensor
2:Both sensors
6| Floor temp limit| 30.0°C| 20.0°C — 50.0°C
7| Temp unit| 00: °C| 00: °C
01: °F
8| Output delay| 00: OOs| 00: OOs
1:30s
2:60s
3:90s
9| Temp deviation| 01: 1.0°C| 00: 0.5°C ,1:1.0°C
2:2.0°C .,3:3.0°C
10| Reverse output| 00: OFF| 00: OF 01: ON
11| schedule| 01:5+1+1| 00:7
01: 5+1+1
12| Adaptive functi| 01: ON| 00: OF 01: ON
13| Reset| 00: No| 00: No 01: YES

Room temp calibration: Calibrate the temp detected by the room sensor.
Floor temp calibration: Calibrate the temp detected by ﬂoor sensor.
Anti-frozen function: This option allows you to bring warmth to your plant and pet at a lower temp display when you turn oﬀ the thermostat.
A hydronic heating system, it will keep away from freezing.
Sensor selection:
00 Room sensor: Run by room sensor.
01 Floor sensor: Run by ﬂoor sensor.
02 Both sensors: Run by room sensor with ﬂoor temp limit.
Floor temp limit: If you choose both sensors, the ﬂoor temp limit must be set to protect the ﬂoor.
Temp units: °C and °F can be selected.
Output delay : This option help you avoid inadvertent operation on heating.
Temp deviation: The deviation is 1°C. The thermostat starts to work when the actual temp is 1°C lower than a stamp and stops working when the actual temp is 1°C higher than the set temp.
Reverse output: This function works for the cooling system. When the temp is 1°C higher than the set temp, the thermostat will disconnect the cooling system. otherwise, it will connect the cooling system.
Schedule : Select a weekly schedule for the Edit. There are 2 options: 7: each day from Mon to Sun can be set individually.
5+1+1: 5 days from Mon to Fri have the same events, Sat and Sun can be set individually.
Adaptive function: After several days of installation and use, the Adaptive function ensures that the required temp has already been reached when the next event begins.
Reset: All parameters are restored to default values.

7.9 Open window detection
This function only works when room sensor or both sensors is selected. The thermostat with this function will shut oﬀ automatically for 15 min when the window opens, as it can detect that the room temp plummets.