LLOYD S EA-9000 Color LED Lamp User Guide

LLOYD S EA-9000 Color LED Lamp

QUICK GUIDE

PLEASE READ THIS INSTALLATION GUIDE BEFORE OPERATING YOUR PRODUCT
This appliance is not intended for use by persons (including children) whose physical, sensory or mental capacities are different or reduced, or lack of experience or knowledge. Children should be supervised to ensure that they do not use the devices as toys.

The operation of this device is subject to two conditions:
This lamp may not cause harmful interference
This lamp must accept any interference, including interference that may be caused by undesired operation.

Safety instructions

Read and follow all safety instructions:

• The lamp is not waterproof. Avoid exposing it to splashing or dripping water.
• The operating temperature should be within -10 °C to 40 °C (14 °F to 104 °F).
• The lamp’s internal light source is unfixable. If it breaks, you must replace the entire lamp.
• Do not install the lamp with a dimming driver.
• Avoid installing the lamp near heat sources.
• Avoid installing the lamp near potentially dangerous sources (e.g., candles, liquid-filled objects).

Introduction

Control your Wi-Fi LED lamp with voice commands and explore a universe of colors that will brighten your life.

Contents
Color LED Lamp
Quick guide

Diagram

Installation

Installing steps:

1. Before installing the lamp, ensure to turn off the switch of the socket or the lamp holder.
2. Screw the lamp into the socket, and turn on the switch or the lamp holder. The device will begin to flash.
3. If the lamp does not flash, refer to #6 in the “troubleshooting” section to restore the lamp to its factory default settings.

Pairing the device with the Amazon Alexa App

What you need:
A Wi-Fi router supporting the 2.4 GHz and 802.11 b/g/n bands. 5 GHz is not supported.
A smartphone or tablet running iOS 8.0 (or above) or Android 4.3 (or above).

1. Download the Amazon Alexa app from the App Store (iOS device) or Google Play (Android devices).

2. Connect your smartphone to your home network, and ensure the smartphone’s Bluetooth is already on.

3. The lamp will rapidly flash (cold light, 6500K, 10% brightness, 2 times per second) when turning on the power supply. If the lamp does not flash, refer to #6 in the “troubleshooting” section to restore the lamp to it’s factory default settings.
   Attention: Please complete the pairing process within 5 minutes of powering on the device.

4. Open the App and click Devices . Select and then click Add Device.

5. Select Light -> Evolux, then select your corresponding device, and follow the onscreen instructions to complete pairing. If prompted by the App, scan the 2D barcode on the last page of this guide.

How to create lamps groups

You can group multiple lamps to turn them on with a single voice command via Alexa. A group, for example, might include all the lights in the bedroom or the lights in the living room. Follow these steps to create a group:

1. Click Devices .
2. Select the lamp, then click Add group.
3. Enter a name for your group or choose an option from the list. Select Next.
4. Choose the lights you want to add to the group and click Save.
5. Once set up, all you have to do is tell Alexa which group of lights you want to control. For example, say: “Alexa, turn on the living room.”

How to detect the lamp in the Amazon Alexa App

1. Ask Alexa to discover your voice. Say, “Alexa, discover my devices.”
2. Alexa will start to discover devices; this may take up a few seconds.
3. When Alexa finds your devices, the device name will show on the device list.

Use of the device with Alexa
To use your device with Alexa, say, “Alexa, turn on the lamp.”

Technical specifications

• Voltage: 120 VAC 60 Hz
• Wattage: 9 W
• Color rendering index (CRI): 80
• Power factor: 0.5
• Luminous Flux: 806 lm
• Color: RGB CCT
• Color temperature: 2 700 – 6 500 K
• Lifespan: 25 000 hours
• Base socket: E26
• Operating temperature: -10 °C to 40 °C (14 °F to 104 °F).
• Relative humidity: 80%
• Wi-Fi frequency: 2.4 GHz
• Wi-Fi protocol: IEEE 802.11b/g/n
• Dimensions (W x H x D): 60 mm x 60 mm x 116 mm

Troubleshooting

I cannot connect the lamp to Amazon Alexa.

• a. Verify that the Wi-Fi function of your smartphone is enabled. Ensure you connect to a 2.4 GHz band (the 5 GHz band is not supported).
• b. Ensure that the distance between the lamp and the modem is less than 50 ft or within the modem’s network coverage.
• c. Check that the lamp enters configuration mode by verifying that it is blinking.
• d. Make sure that the Bluetooth function on your smartphone is enabled.

The lamp lost connection.

• a. Check if the device is on.
• b. Check that your home network is stable.
• c. Go to Devices in the Amazon Alexa App and remove the lamp. Then reconnect it to the Wi-Fi network, following the on-screen instructions to complete the pairing.

Is it possible to control groups with voice commands?

• a. It is possible to group-control lamps with voice commands by creating a group from the Amazon Alexa App.

Where can I find the barcode?

• a. You can find the barcode on the last page of this guide.

What should I do if I do not have a barcode or the configuration has failed?
If you do not have a barcode or the configuration has failed, perform the following steps:

1. Select DON’T HAVE A BARCODE?
2. Turn on the device until the light starts flashing rapidly.
3. Press NEXT to continue with the configuration.

How to restore the factory default settings?

1. Start with turning off the lamp for at least 5 seconds.
2. Immediately turn it on for 2 seconds, then turn it off.
3. Immediately turn it on again for 2 seconds, and then turn it off.
4. Then turn on the lamp and wait for 5 seconds. If the reset was successful, the lamp will start to blink (6 500 K, 10% brightness, 1 minute later go to 100% brightness).

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Warning : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferen-ce to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20 cm between the radiator & your body.

IMPORTED INTO MEXICO BY:
ZUTTO TECHNOLOGIES, S. A. DE C. V.
Avenida Ejército Nacional No. 505 Interior 1602, Col. Granada Miguel Hidalgo, Ciudad de México, México C.P. 11520 Teléfono: 55 68447575
R.F.C.: ZTE161017KT6
evoluxtech.com
Errata sheet
Correct website: evolux.tech

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>